Shimano
Shimano Deore XT M737 Series NOS Classic Quick Release Rear Skewer
£35.00
✓ Original skewer - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Shimano Deore XT rear wheel skewer (or hub spindle if you prefer), hailing from Japan and in production during the 1990s (yet still new & unused after all this time!). Made from steel/aluminium/plastic and weighing in at 61 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Production Era - 1990s
Country - Japanese
Material - Steel / Aluminium / Plastic
Weight - 61 g
Stock Code - D-SKW-R45C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Skewer Type - Quick Release
Spacing* - 146 mm
Threaded Section - 23 mm
End Nut Length - 17 mm
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
Shimano Deore XT Oversized NOS Vintage MTB Brake Cable Inners
£15.00
✓ Original cables - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Shimano Deore XT set of 2 inner cables (or wires if you prefer), hailing from Japan and in production during the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
OVERVIEW
Production Era - 1980s
Country - Japanese
Stock Code - D-CAB-P6V
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Bike Suitability - MTB
Cable Type - Brake
Length (F/R) - 170 cm / 170 cm
Wire Diameter - 2.0 mm
End Nipple Type - Barrel
End Diameter - 6 mm (8 mm With Cover)
Barrell End Thickness - 9 mm
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Cable Type - brake and gear cables have different specifications and are not interchangeable.
Length (F/R) - it's important to check the cables are long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.
End Nipple Type - only relevant for brake cables. 'Pear' type cable ends step down in size to allow them to be used with drop bar levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.
End Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.
Shimano Dura-Ace (855 9003-2) Vintage Top Tube Brake Cable Guides / Housing Clips Set
£35.00
✓ Original parts - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping
Shimano Dura-Ace top tube cable guides, hailing from Japan and in production during the 1970s. Made from steel and weighing in at 9 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guides!
The cable guides have been cleaned, checked and graded as mint condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - 855 9003-2
Production Era - 1970s
Country - Japanese
Material - Steel
Weight - 9 g
Stock Code - U-CGT5V
TECHNICAL INFO
Tube Diameter - 25.4 mm (Standard Steel Frame)
Number of Cables - Single
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Tube Diameter - most steel frames will have a top tube with an outside diameter of 25.4 mm, this was standard for a long time but there are 'oversized' tubes that have a diameter of 28.6 mm. Most aluminium frames will have larger 31.8 mm tubes, the exception being earlier ones with lugged construction that have 25.4 mm tubes.
Number of Cables - the number of cables the guides are designed to accept.
-
-
-
Shimano Dura-Ace (855 9003-2) Vintage Top Tube Brake Cable Guides / Housing Clips Set
£35.00
✓ Original parts - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping
Shimano Dura-Ace top tube cable guides, hailing from Japan and in production during the 1970s. Made from steel and weighing in at 9 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guides!
The cable guides have been cleaned, checked and graded as mint condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - 855 9003-2
Production Era - 1970s
Country - Japanese
Material - Steel
Weight - 9 g
Stock Code - U-CGT7V
TECHNICAL INFO
Tube Diameter - 25.4 mm (Standard Steel Frame)
Number of Cables - Single
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Tube Diameter - most steel frames will have a top tube with an outside diameter of 25.4 mm, this was standard for a long time but there are 'oversized' tubes that have a diameter of 28.6 mm. Most aluminium frames will have larger 31.8 mm tubes, the exception being earlier ones with lugged construction that have 25.4 mm tubes.
Number of Cables - the number of cables the guides are designed to accept.
-
-
-
Shimano Dura-Ace (855 9003-2) Vintage Top Tube Brake Cable Guides / Housing Clips Set
£35.00
✓ Original parts - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping
Shimano Dura-Ace top tube cable guides, hailing from Japan and in production during the 1970s. Made from steel and weighing in at 9 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guides!
The cable guides have been cleaned, checked and graded as mint condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - 855 9003-2
Production Era - 1970s
Country - Japanese
Material - Steel
Weight - 9 g
Stock Code - U-CGT6V
TECHNICAL INFO
Tube Diameter - 25.4 mm (Standard Steel Frame)
Number of Cables - Single
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Tube Diameter - most steel frames will have a top tube with an outside diameter of 25.4 mm, this was standard for a long time but there are 'oversized' tubes that have a diameter of 28.6 mm. Most aluminium frames will have larger 31.8 mm tubes, the exception being earlier ones with lugged construction that have 25.4 mm tubes.
Number of Cables - the number of cables the guides are designed to accept.
-
-
-
Shimano Dura-Ace (SM-CG10) Vintage Single Rear Tunnel Down Tube Gear Cable Guide / Clip
£30.00
✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping
Shimano Dura-Ace down tube gear cable guide, hailing from Japan and in production from the 1970s to the 1980s. Made from steel and weighing in at 37 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guide!
The cable guide has been cleaned, checked and graded as mint condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - SM-CG10
Production Era - 1970s & 1980s
Country - Japanese
Material - Steel
Weight - 37 g
Stock Code - U-CGG14V
NB - Modified from double to single guide.
TECHNICAL INFO
Number of Cables - Single
Guide Type - Rear Tunnel
Tube Diameter - 28.0 mm - 28.6 mm
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Number of Cables - the number of cables the guide is designed to accept.
Guide Type - some setups require specific guides for the derailleurs to operate correctly. Tunnels simply act as a channel to guide the cable whereas stops create an end point for the cable housing, giving the cable the leverage it needs. Bar control stops are required when using handlebar shifters if your frame doesn't have any guides or braze-ons.
Tube Diameter - most steel (and early lugged aluminium) frames will have a down tube of 28.0 mm - 28.6 mm, this was standard for a long time but there are 'oversized' steel and aluminium tubes that have a diameter of 31.8, 34.9 and even 38.1 mm.
Shimano Dura-Ace (SM-ST74) Classic Down Tube Gear Cable Stops / Barrel Adjusters
£20.00
✓ Original parts - in production from the 1990s to the 2000s
✓ Checked & cleaned
✓ Worldwide shipping
Shimano Dura-Ace down tube cable stops / adjusters, hailing from Japan and in production from the 1990s to the 2000s. Made from aluminium and weighing in at 31 grams (for the pair). A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.
The stops have been cleaned, checked and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - SM-ST74
Production Era - 1990s & 2000s
Country - Japanese
Material - Aluminium
Weight - 31 kg
Stock Code - U-CGG-A8C
TECHNICAL INFO
Back Shape - Curved
Boss Thread Size - M5 / 5 mm (Standard)
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Back Shape - most adjustable stops have curved backs, designed to fit steel frames with standard braze-ons and a down tube diameter of around 28.6 mm (1 1/8"). Some oversized frames have flat plates at the base, these require stops with flat backs.
Boss Thread Size - most frames will have M5 (5mm) threads on the shifter bosses as this has been standard for a long time. However, if you're converting an older frame with Shimano bosses (M4.5 / 4.5 mm threads) or French bosses (5 x 1 mm threads) you'll need to use different bolts to fix the adjusters to your frame.
Shimano Dura-Ace / 600 (L-600) Fingertip Control Vintage 5/6 Speed Bar-End Shifters
£65.00
✓ Original shifters - produced in the 1970s
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping
Shimano Dura-Ace / 600 shifters, hailing from Japan and in production during the 1970s. Made from aluminium/steel/rubber and weighing in at 165 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The shifters have been checked over by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - L-600
Production Era - 1970s
Country - Japanese
Material - Aluminium / Steel / Rubber
Weight - 165 g
Stock Code - U-G3-S-H17V
TECHNICAL INFO
Speed* - 5 Speed, 6 Speed
Shift System - Friction
Shifter Type - Bar-End
Chainset Compatibility - 2/3x (Double/Triple)
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼SAFETY & COMPLIANCE
- This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.
Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland
-
▼HELP SECTION
-
Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction shifters you can in theory run any shifters with any speed setup.
Shift System - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting. For this to work correctly you must use the same shift system as your rear derailleur, if you're using friction levers you can mix and match.
Shifter Type - most have obvious names other than ‘brifters’ and ‘trigger’ shifters. These are brake levers and gear levers combined, brifters are for road drop handlebars and trigger shifters are designed to be used on flat bars, usually for mountain bikes.
Chainset Compatibility - the number of rings on the chainset the left shifter is capable of working with (providing the front derailleur is capable of the same).
Shimano Dura-Ace / 600 (SM-CS30) NOS Vintage Chain Stay Gear Cable Guide / Clip
£10.00
✓ Original part - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping
Shimano Dura-Ace / 600 chain stay gear cable guide, hailing from Japan and in production during the 1970s (yet still new & unused after all this time!). Made from steel and weighing in at 10 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guide!
OVERVIEW
Model ID - SM-CS30
Production Era - 1970s
Country - Japanese
Material - Steel
Weight - 10 g
Stock Code - D-CGG-C2V
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Cable Opening Diameter - 6 mm
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Cable Opening Diameter - this will normally be around 4 mm which is the modern standard for gear cable housing, although some older bikes used larger diameter 5 mm housing (the same as brake cable outer). If using an end ferrule, measure that rather than the cable outer diameter.
Shimano Dura-Ace / 600 (SM-CS30) NOS Vintage Chain Stay Gear Cable Guide / Clip
£10.00
✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping
Shimano Dura-Ace / 600 chain stay gear cable guide, hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 10 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guide!
OVERVIEW
Model ID - SM-CS30
Production Era - 1970s & 1980s
Country - Japanese
Material - Steel
Weight - 10 g
Stock Code - D-CGG-C1V
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Cable Opening Diameter - 6 mm
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Cable Opening Diameter - this will normally be around 4 mm which is the modern standard for gear cable housing, although some older bikes used larger diameter 5 mm housing (the same as brake cable outer). If using an end ferrule, measure that rather than the cable outer diameter.
Shimano Dura-Ace / Deore XT / 600 (134 0300 / 0400) NOS Vintage Crank Arm Bolts Set
£10.00
✓ Original parts - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping
Shimano Dura-Ace / Deore XT / 600 crankset fixing bolts (or bottom bracket screws if you prefer), hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 31 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank bolts!
OVERVIEW
Model ID - 134 0300 / 0400
Production Era - 1970s & 1980s
Country - Japanese
Material - Steel
Weight - 31 g
Stock Code - D-G5-CB49V
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Crank Bolt Type - 14 mm Hex
Crank Bolt Thread - M8 x 1 mm (Standard)
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼SAFETY & COMPLIANCE
- This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.
Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland
-
▼HELP SECTION
-
Crank Bolt Type - 15 mm hex bolts used to be standard but some older TA, Stronglight and Zeus cranks used a larger 16 mm bolt, plus a few Japanese makers used a smaller 14 mm hex head. Allen key types were introduced in the 1980s and some are self-extracting, which means the crank removes itself when you undo the bolts.
Crank Bolt Thread - All square taper bottom brackets have a standard M8 x 1 mm thread, the only different thread types you’ll find on crank bolts are the much larger M12 & M15 bolts that are specifically for Octalink and ISIS bottom brackets.
Shimano Exage (CS-HG50) NOS Classic 7 Speed Hyperglide 14-32 Cassette
£50.00
✓ Original cassette - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Shimano Exage cassette (or cog set, or sprockets if you prefer), hailing from Japan and in production during the 1990s (yet still new & unused after all this time). Made from steel and weighing in at 403 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Condition Notes - Rust and tarnishing to some sprockets as seen in photos
Model ID - CS-HG50
Production Era - 1990s
Country - Japanese
Material - Steel
Weight - 403 g
Stock Code - D-G3-CAS61C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Speed - 7 Speed
Spline Pattern - Shimano Hyperglide
Range - 14-32
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼SAFETY & COMPLIANCE
- This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.
Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland
-
▼HELP SECTION
-
Speed - the number of cogs on the cassette.
Spline Pattern - the shape of the cogs where they slide on to the freehub body, this must match the spline pattern of your hub to able to fit. In the 1980s Shimano introduced Uniglide cassettes that share the same spline pattern as their now standard Hyperglide, but the smallest sprocket threads on to the hub to secure it rather than using a conventional lockring, these will only fit hubs with a threaded section on the outside of the freehub body.
Range - the number of teeth on the smalles and largest cogs, this gives you an indication of how hard or easy the gearing will be, the lower the number the harder the gears. The tooth count of the cogs inbetween are usually evenly spaced, ie: a 6 speed 14-24 freewheel would likely have cog sizes 14, 16, 18, 20, 22 & 24.
Shimano Exage Sport (FC-A450) c.1988 Vintage 130 BCD 170 mm Right Crank Arm / Spider
£30.00
✓ Original part - produced in the 1980s
✓ Professionally checked & cleaned
✓ Worldwide shipping
Shimano Exage Sport right crank arm/spider, hailing from Japan and dating back to 1988. Made from aluminium and weighing in at 338 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
The crank arm has been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - FC-A450
Production Era - 1980s
Country - Japanese
Material - Aluminium
Weight - 338 g
Stock Code - U-CA-SR14V
TECHNICAL INFO
Chainring Count - Double
BCD - 130 BCD
Crank Arm Length - 170 mm
Pedal Threads - Standard (9/16" x 20 TPI)
Bottom Bracket Type - Square Taper
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Chainring Count - the number of chainrings the crank was designed to fit. Fixed gear track bikes, single-speeds and some geared bikes use a single chainring, road bikes commonly use a double (two rings) and most touring bikes and mountain bikes will use a triple chainset (three rings).
BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter), and this needs to match the BCD of your chainring(s). To calculate this, measure the distance in millimeters from the centre of any chainring bolt hole to the centre of an adjacent one and multiply it by 1.709 (you’ll likely need to round the resulting number up or down a little to get your BCD measurement).
Crank Arm Length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.
Pedal Threads - the pattern of the thread that your pedals screw into, this is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).
Bottom Bracket Type - ‘square taper’, as the name suggests have a square shaped axle that slots into the crank and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a crank that matches.
Shimano MF-Z012 c.1990 Vintage 6 Speed 13-24 Freewheel
£40.00
✓ Original part - in production from the 1980s to the 1990s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & carefully cleaned
✓ Worldwide shipping
Shimano MF-Z012 freewheel, hailing from Japan and dating back to 1990. Made from steel and weighing in at 386 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong freewheel!
The freewheel's been carefully cleaned, thoroughly checked by one of our mechanics and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy, and please consider that freewheels wear with chains, so used freewheels can occasionally skip when partnered with new (and some used) chains. This can usually be avoided by using a compatible used chain of similar age, but there is no way for us to confirm which chain will work with which freewheel.OVERVIEW
Model ID - MF-Z012
Production Era - 1980s & 1990s
Country - Japanese
Material - Steel
Weight - 386 g
Stock Code - U-FW192V
TECHNICAL INFO
Speed (No of Cogs) - 6 Speed
Range - 13-24
Threading - English/ISO: 1.375 x 24 TPI
Stack Height - 32.5 mm
Cog Width - 3/32" (Standard)
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Speed - the number of cogs on the freewheel.
Range - the number of teeth on the smalles and largest cogs, this gives you an indication of how hard or easy the gearing will be, the lower the number the harder the gears. The tooth count of the cogs inbetween are usually evenly spaced, ie: a 6 speed 14-24 freewheel would likely have cog sizes 14, 16, 18, 20, 22 & 24.
Threading - this needs to match the thread of your rear hub. ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Hubs with a French thread must be used with a French threaded freewheel.
Stack Height - the total height (or width if you're looking at it when installed) of the freewheel, this is measured from the base (back of the largest cog) to the top (front of the smallest cog).
Cog width - this is mainly relevant for singlespeed and some older 3 or 4 speed freewheels - if this is ⅛” then you must use a ⅛” chain, but most freewheels (especially multiple speed ones) will use a standard 3/32” chain.
Shimano Mountain LX / Exage BB-M450 68-T NOS Vintage 118 mm Bottom Bracket Axle
£25.00
✓ Original part - in production from the 1980s to the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Shimano Mountain LX / Exage bottom bracket axle (or BB spindle if you prefer), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time). Made from steel and weighing in at 212 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
Exage Mountain & Exage Trail also used these axles, so they are compatible with those too.
OVERVIEW
Production Era - 1980s & 1990s
Country - Japanese
Material - Steel
Weight - 212 g
Stock Code - D-G3-BB-AS25V
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Axle Type - Square Taper
Axle Markings - 68-T (3A)
Axle Length (D) - 118 mm
Axle Centre (B) - 52 mm
Axle Drive Side (C) - 37 mm
Axle Non-Drive Side (A) - 36 mm
Shell Width - 68 mm
NB: Check the help section to see how we take these measurements.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼SAFETY & COMPLIANCE
- This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.
Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland
-
▼HELP SECTION
- We've provided reference below to illustrate how we take the measurements.
Axle Type - for square tapers, the ISO introduced a standard for European makers in the early 90s, JIS then did the same in Asia. Before then it was not so simple, and although there is a degree of interchangeability, the best way to make sure you have the right axle is to stick to the same brand from the same era, ideally the proprietary model.
Axle Length (D) - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing an axle that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.
Centre (B) - measured from the outside of the 'shoulders' of the bearing races, as seen in the diagram.
Drive Side (C) - the right side (with any logos etc on the axle facing you), your right crank and chainrings will mount to this side.
Non-Drive Side (A) - the left side, where the left crank arm will be mounted.
Shell Width - the width of the bottom bracket shell the axle was designed to fit, measured at its widest point.
Shimano NOS Classic Quick Release Front Skewer
£12.50
✓ Original skewer - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Shimano front wheel skewer (or hub spindle if you prefer), hailing from Japan and in production during the 1990s (yet still new & unused after all this time!). Made from steel/plastic and weighing in at 87 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Production Era - 1990s
Country - Japanese
Material - Steel / Plastic
Weight - 87 g
Stock Code - D-SKW-F26C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Skewer Type - Quick Release
Spacing* - 113 mm
Threaded Section - 20 mm
End Nut Length - 15 mm
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
Shimano NOS Classic Quick Release Front Skewer
£10.00
✓ Original skewer - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Shimano front wheel skewer (or hub spindle if you prefer), hailing from Japan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium/steel/plastic and weighing in at 58 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Production Era - 1990s
Country - Japanese
Material - Aluminium / Steel / Plastic
Weight - 58 g
Stock Code - D-SKW-F29C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Skewer Type - Quick Release
Spacing* - 112 mm
Threaded Section - 22 mm
End Nut Length - 16 mm
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
Shimano NOS Classic Quick Release Front Skewer
£15.00
✓ Original skewer - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Shimano front wheel skewer (or hub spindle if you prefer), hailing from Japan and in production during the 1990s (yet still new & unused after all this time!). Made from steel/plastic and weighing in at 93 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Production Era - 1990s
Country - Japanese
Material - Steel / Plastic
Weight - 93 g
Stock Code - D-SKW-F30C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Skewer Type - Quick Release
Spacing* - 109 mm
Threaded Section - 22 mm
End Nut Length - 16 mm
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
Shimano NOS Vintage Top Tube Brake Cable Guides / Housing Clips Set
£17.50
✓ Original parts - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping
Shimano top tube cable guides, hailing from Japan and in production during the 1970s (yet still new & unused after all this time!). Made from steel and weighing in at 10 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guides!
OVERVIEW
Condition - New Old Stock*
Production Era - 1970s
Country - Japanese
Material - Steel
Weight - 10 g
Stock Code - D-CGT26V
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Tube Diameter - 25.4 mm (Standard Steel Frame)
Number of Cables - Single
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Tube Diameter - most steel frames will have a top tube with an outside diameter of 25.4 mm, this was standard for a long time but there are 'oversized' tubes that have a diameter of 28.6 mm. Most aluminium frames will have larger 31.8 mm tubes, the exception being earlier ones with lugged construction that have 25.4 mm tubes.
Number of Cables - the number of cables the guides are designed to accept.
-
-
-
Shimano Positron (LC-410) Vintage Positron Right Stem Shifter
£20.00
✓ Original shifter - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping
Shimano Positron right stem shifter, hailing from Japan and in production during the 1970s. Made from plastic/steel and weighing in at 64 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifter!
The shifter's been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - LC-410
Production Era - 1970s
Country - Japanese
Material - Plastic / Steel
Weight - 64 g
Stock Code - U-S-SR2V
TECHNICAL INFO
Shift Type - Positron (No Friction Setting)
Speed* - 5 Speed
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
Shimano STX RC (8CF 9810) BR-MC40 NOS/NIB Classic V-Brake Pads
£30.00
✓ Original brake pads - in production from the 1990s to the 2000s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping
Shimano STX RC set of 4 rim brake pads (or blocks, or shoes if you prefer), hailing from Japan and in production from the 1990s to the 2000s (yet still new & unused after all this time). Weighing in at 150 grams (the weight and price displayed is for 4 pads). A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Model ID - 8CF 9810
Production Era - 1990s & 2000s
Weight - 150 g
Country - Japanese
Stock Code - D-BP-S16C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Brake Fit - V-Brake
Pad Type - One Piece
Length - 70 mm
Height - 15 mm
Rim Type - Alloy
NB: Modern production brake pads will normally offer the best performance, but if you wish to keep everything period correct original ones are still a great option. As with all classic parts though, they must be installed correctly and ridden with care.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Brake Fit - brake pads are specific to the type of brake so you need to use the correct ones.
Pad Type - replaceable (also known as cartridge) brake pads have inserts that can be replaced once they wear out. With one piece pads you do not have this option.
Rim Type - some wheel rims such as ceramic or carbon ones require brake pads to be made of specific compounds. If you have steel rims you can use pads designed for alloy rims but you will get much better performance when using the correct pads.
Shimano Tiagra (HB-4500) NOS/NIB Classic 32h Front Hub
£45.00
✓ Original hub - produced in the 2000s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping
Shimano Tiagra front hub, hailing from Japan and in production during the 2000s. Made from aluminium/steel and weighing in at 208 grams - pretty lightweight for a front hub at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Bearing / Race Condition - New Old Stock*
Model ID - HB-4500
Production Era - 2000s
Country - Japanese
Material - Aluminium / Steel
Weight - 208 g
Stock Code - D-G3-HU-F57C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Spoke Drilling - 32 Hole
Spacing (O.L.D.) - 100 mm
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼SAFETY & COMPLIANCE
- This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.
Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland
-
▼HELP SECTION
-
Spoke Drilling - the number of holes for the spokes, your wheel rim needs to match the hub exactly.
Spacing (O.L.D.) - the width of the hub measured at its widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. This measurement needs to match the inside of your fork's dropouts. Steel forks can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon forks should never be stretched.
Shimano Tourney (FD-TY30) NOS Classic Clamp-On 28.6 mm Front Derailleur
£20.00
✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Shimano Tourney front derailleur, hailing from Japan and in production during the 1990s (yet still new & unused after all this time!). Made from steel/plastic and weighing in at 169 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Model ID - FD-TY30
Production Era - 1990s
Country - Japanese
Material - Steel / Plastic
Weight - 169 g
Stock Code - D-FM176C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Chainset Type - Double / Triple
Frame Fixing - Clamp-On 28.6 mm
Pull Type - Bottom Pull
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.
Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.
Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.
Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.
Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.
Shimano Tourney (Y563 98100) NOS/NIB Classic 10T Jockey Wheels
£10.00
✓ Original jockey wheels - in production from the 1990s to the 2000s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping
Shimano Tourney jockey wheels (or derailleur pulleys if you prefer), hailing from Japan and in production from the 1990s to the 2000s (yet still new & unused after all this time). Made from plastic and weighing in at 27 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Model ID - Y563 98100
Production Era - 1990s & 2000s
Country - Japanese
Material - Plastic
Weight - 27 g
Stock Code - D-JCK17C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Teeth - 10
Compatible Speed* - 5 Speed, 6 Speed, 7 Speed
Diameter (OD) - 38 mm
Thickness - 10.4 mm
Centre Hole (ID) - 5.3 mm
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Teeth - the tooth count has increased with the introduction of more gears, but this happened very gradually so 10 tooth jockey wheels were standard for a very long time.
*Compatible Speed - the number of cogs the jockey wheels were designed to be used with. When using derailleurs for indexed shifting it's important to stick to this, but friction shifting is much more forgiving so you're unlikely to have any problems using the next speed up or down, providing all the measurements are correct.
Diameter (OD) - the diameter of the jockey wheels, from the outside edge of the teeth. It’s important to stay close to the ones you're replacing to ensure they fit.
Thickness - measured at the widest point, by the centre hole. The spacing has generally become narrower over the years to accommodate more gears.
Centre Hole (ID) - the inside diameter (usually inside the bushing/spacer if present). This rarely presents a problem, but some older jockey wheels have a different diameter so it's worth double checking.