All Items 10% Off

Campagnolo Nuovo/Super Record (1034/P) Small Flange c.1976 Vintage 36h Rear Hub

£71.25 £95.00

✓ Original hub - in production from the 1960s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked, cleaned & serviced
✓ Worldwide shipping

Campagnolo Nuovo/Super Record rear hub, hailing from Italy and dating back to 1976. The skewer design is of the ’pre-CPSC’ era produced until around 1978. Made from aluminium/steel and weighing in at 291 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong hub!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Spoke Drilling - the number of holes for the spokes, your wheel rim needs to match the hub exactly.

Spacing (O.L.D.) - the width of the hub measured at its widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. This measurement needs to match the inside of your frame's dropouts. Steel frames can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon frames should never be stretched.

Speed - the number of cogs the hub was designed to be used with.

Sprocket Fitting - for cassette hubs this refers to the spline pattern (the shape of the cogs where they slide on to the hub) and this must match the cassette you intend to use. With freewheel hubs it refers to the thread, ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Freewheel hubs with a French thread must be used with a French threaded freewheel.

Strongy Small Flange Vintage 36h Rear Hub

£18.75 £25.00

✓ Original hub - in production from the 1970s to the 1980s
✓ Super lightweight for the era - only 224 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked, cleaned & serviced
✓ Worldwide shipping

Strongy rear hub, hailing from France and in production from the 1970s to the 1980s. Made from aluminium/steel and weighing in at 224 grams - incredibly lightweight for a rear hub at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong hub!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Spoke Drilling - the number of holes for the spokes, your wheel rim needs to match the hub exactly.

Spacing (O.L.D.) - the width of the hub measured at its widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. This measurement needs to match the inside of your frame's dropouts. Steel frames can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon frames should never be stretched.

Speed - the number of cogs the hub was designed to be used with.

Sprocket Fitting - for cassette hubs this refers to the spline pattern (the shape of the cogs where they slide on to the hub) and this must match the cassette you intend to use. With freewheel hubs it refers to the thread, ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Freewheel hubs with a French thread must be used with a French threaded freewheel.

Le Tour Large Flange Vintage 32h Front Hub

£18.75 £25.00

✓ Original hub - produced in the 1970s
✓ Super lightweight for the era - only 169 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked, cleaned & serviced
✓ Worldwide shipping

Le Tour front hub, hailing from France and in production during the 1970s. Made from aluminium/steel and weighing in at 169 grams - incredibly lightweight for a front hub at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong hub!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Spoke Drilling - the number of holes for the spokes, your wheel rim needs to match the hub exactly.

Spacing (O.L.D.) - the width of the hub measured at its widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. This measurement needs to match the inside of your fork's dropouts. Steel forks can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon forks should never be stretched.

Campagnolo Veloce (HB-00VL) Classic 36h Front Hub

£26.25 £35.00

✓ Original hub - produced in the 1990s
✓ Super lightweight for the era - only 157 grams!
✓ Professionally checked, cleaned & serviced
✓ Worldwide shipping

Campagnolo Veloce front hub, hailing from Italy and in production during the 1990s. Made from aluminium/steel and weighing in at 157 grams - incredibly lightweight for a front hub at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Spoke Drilling - the number of holes for the spokes, your wheel rim needs to match the hub exactly.

Spacing (O.L.D.) - the width of the hub measured at its widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. This measurement needs to match the inside of your fork's dropouts. Steel forks can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon forks should never be stretched.

Resilion Continental Vintage 32h Front Hub

£56.25 £75.00

✓ Original hub - in production from the 1950s to the 1960s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked, cleaned & serviced
✓ Worldwide shipping

Resilion Continental front hub, hailing from Great Britain and in production from the 1950s to the 1960s. Made from steel and weighing in at 292 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong hub!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Spoke Drilling - the number of holes for the spokes, your wheel rim needs to match the hub exactly.

Spacing (O.L.D.) - the width of the hub measured at its widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. This measurement needs to match the inside of your fork's dropouts. Steel forks can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon forks should never be stretched.

Maillard Large Flange c.1982 Vintage 36h Front Hub

£22.50 £30.00

✓ Original hub - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked, cleaned & serviced
✓ Worldwide shipping

Maillard front hub, hailing from France and dating back to 1982. Made from aluminium/steel and weighing in at 249 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong hub!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Spoke Drilling - the number of holes for the spokes, your wheel rim needs to match the hub exactly.

Spacing (O.L.D.) - the width of the hub measured at its widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. This measurement needs to match the inside of your fork's dropouts. Steel forks can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon forks should never be stretched.

Campagnolo Gran Sport / Cambio Corsa (1001/1) FB Made 'Open C' Vintage 36h Front Hub

£131.25 £175.00

✓ Original hub - in production from the 1940s to the 1950s
✓ Lightweight for the era - just 205 grams
✓ Professionally checked, cleaned & serviced
✓ Worldwide shipping

Campagnolo Gran Sport / Cambio Corsa front hub, hailing from Italy and in production from the 1940s to the 1950s. Made from aluminium/steel and weighing in at 205 grams - pretty lightweight for a front hub at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Spoke Drilling - the number of holes for the spokes, your wheel rim needs to match the hub exactly.

Spacing (O.L.D.) - the width of the hub measured at its widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. This measurement needs to match the inside of your fork's dropouts. Steel forks can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon forks should never be stretched.

Campagnolo Nuovo Tipo / Gran Sport (1264) Small Flange c.1976 Vintage 36h Front Hub

£52.50 £70.00

✓ Original hub - in production from the 1960s to the 1980s
✓ Lightweight for the era - just 217 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked, cleaned & serviced
✓ Worldwide shipping

Campagnolo Nuovo Tipo / Gran Sport front hub, hailing from Italy and dating back to 1976. The skewer design is of the ’pre-CPSC’ era produced until around 1978. Made from aluminium/steel and weighing in at 217 grams - pretty lightweight for a front hub at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong hub!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Spoke Drilling - the number of holes for the spokes, your wheel rim needs to match the hub exactly.

Spacing (O.L.D.) - the width of the hub measured at its widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. This measurement needs to match the inside of your fork's dropouts. Steel forks can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon forks should never be stretched.

Brooks Professional Pre-Softened Vintage Brown Leather Saddle

£82.50 £110.00

✓ Original saddle - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping

Brooks Professional saddle, hailing from Great Britain and in production during the 1980s. Made from leather/steel and weighing in at 572 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Gallet Sprung Vintage Brown Saddle

£30.00 £40.00

✓ Original saddle - in production from the 1940s to the 1950s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping

Gallet saddle, hailing from France and in production from the 1940s to the 1950s. Made from synthetic/steel and weighing in at 956 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Unbranded Swallow Style Laced Vintage Dark Brown Leather Saddle

£131.25 £175.00

✓ Original saddle - produced in the 1950s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping

Unbranded vintage saddle, most likely in production during the 1950s. Made from leather/steel and weighing in at 476 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Selle Italia Turbo c.1987 Vintage Black Leather Saddle

£56.25 £75.00

✓ Original saddle - in production from the 1980s to the 1990s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping

Selle Italia Turbo saddle, hailing from Italy and dating back to 1987. Made from leather/steel/plastic and weighing in at 349 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Selle Italia Turbo Matic 2 Two-Tone c.1996 Classic Black / Grey / Yellow Leather Saddle

£41.25 £55.00

✓ Original saddle - produced in the 1990s
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping

Selle Italia Turbo Matic 2 saddle, hailing from Italy and dating back to 1996. Made from leather/steel and weighing in at 307 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Unbranded Vintage Black Plastic Saddle

£22.50 £30.00

✓ Original saddle - in production from the 1960s to the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping

Unbranded vintage saddle, most likely in production from the 1960s to the 1970s. Made from plastic/steel and weighing in at 548 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Cinelli Unicanitor (Mod. 55) Road Perforated Vintage Black Plastic Saddle

£123.75 £165.00

✓ Original saddle - in production from the 1960s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping

Cinelli Unicanitor saddle, hailing from Italy and in production from the 1960s to the 1980s. Made from plastic/steel and weighing in at 295 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Cinelli Unicanitor (Mod. 65/N) Buffalo Silver Logo Vintage Dark Brown Leather Saddle

£41.25 £55.00

✓ Original saddle - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping

Cinelli Unicanitor saddle, hailing from Italy and in production from the 1970s to the 1980s. Made from leather/plastic/steel and weighing in at 328 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Shimano Dura-Ace (855 9003-2) Vintage Top Tube Brake Cable Guides / Housing Clips Set

£29.75 £35.00

✓ Original parts - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Shimano Dura-Ace top tube cable guides, hailing from Japan and in production during the 1970s. Made from steel and weighing in at 9 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guides!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Tube Diameter - most steel frames will have a top tube with an outside diameter of 25.4 mm, this was standard for a long time but there are 'oversized' tubes that have a diameter of 28.6 mm. Most aluminium frames will have larger 31.8 mm tubes, the exception being earlier ones with lugged construction that have 25.4 mm tubes.

Number of Cables - the number of cables the guides are designed to accept.

Shimano Dura-Ace (855 9003-2) Vintage Top Tube Brake Cable Guides / Housing Clips Set

£29.75 £35.00

✓ Original parts - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Shimano Dura-Ace top tube cable guides, hailing from Japan and in production during the 1970s. Made from steel and weighing in at 9 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guides!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Tube Diameter - most steel frames will have a top tube with an outside diameter of 25.4 mm, this was standard for a long time but there are 'oversized' tubes that have a diameter of 28.6 mm. Most aluminium frames will have larger 31.8 mm tubes, the exception being earlier ones with lugged construction that have 25.4 mm tubes.

Number of Cables - the number of cables the guides are designed to accept.

Charger Vintage Tunnel & Stop Down Tube Gear Cable Guide / Clip

£17.00 £20.00

✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Charger down tube gear cable guide, in production from the 1970s to the 1980s. Made from steel and weighing in at 24 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guide!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Number of Cables - the number of cables the guide is designed to accept.

Guide Type - some setups require specific guides for the derailleurs to operate correctly. Tunnels simply act as a channel to guide the cable whereas stops create an end point for the cable housing, giving the cable the leverage it needs. Bar control stops are required when using handlebar shifters if your frame doesn't have any guides or braze-ons.

Tube Diameter - most steel (and early lugged aluminium) frames will have a down tube of 28.0 mm - 28.6 mm, this was standard for a long time but there are 'oversized' steel and aluminium tubes that have a diameter of 31.8, 34.9 and even 38.1 mm.

Shimano 600 (SM-CG11) Vintage Tunnel & Stop Down Tube Gear Cable Guide / Clip

£17.00 £20.00

✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Shimano 600 down tube gear cable guide, hailing from Japan and in production from the 1970s to the 1980s. Made from steel and weighing in at 25 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guide!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Number of Cables - the number of cables the guide is designed to accept.

Guide Type - some setups require specific guides for the derailleurs to operate correctly. Tunnels simply act as a channel to guide the cable whereas stops create an end point for the cable housing, giving the cable the leverage it needs. Bar control stops are required when using handlebar shifters if your frame doesn't have any guides or braze-ons.

Tube Diameter - most steel (and early lugged aluminium) frames will have a down tube of 28.0 mm - 28.6 mm, this was standard for a long time but there are 'oversized' steel and aluminium tubes that have a diameter of 31.8, 34.9 and even 38.1 mm.

Unbranded Vintage Umbrella Holder Clamp-On Pump Clip

£8.50 £10.00

✓ Original pump clip - in production from the 1960s to the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Unbranded vintage pump clip, most likely in production from the 1960s to the 1970s. Made from steel and weighing in at 24 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump clip

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Pump Securing - umbrella holders provide a base to help secure the pump at one end, traditionally clamped to the seat tube. Peg holders secure the pump by the holes at the ends, these are a bit more versatile as they can be used on top tubes as well, often in pairs if your pump has holes at both ends.

Frame Fixing Type - most pump holders are designed to clamp-on to steel frames. 25.4 mm is the standard top tube size, 28.6 mm (28.0 mm for French frames) is the standard for seat and down tubes. Some holders are available as adjustable clips that fit a large range of tube sizes.

AFA 1 Vintage Umbrella Holder Clamp-On Pump Clip

£10.63 £13.00

✓ Original pump clip - in production from the 1960s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

AFA 1 pump clip, hailing from France and in production from the 1960s to the 1980s. Made from steel and weighing in at 16 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump clip

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Pump Securing - umbrella holders provide a base to help secure the pump at one end, traditionally clamped to the seat tube. Peg holders secure the pump by the holes at the ends, these are a bit more versatile as they can be used on top tubes as well, often in pairs if your pump has holes at both ends.

Frame Fixing Type - most pump holders are designed to clamp-on to steel frames. 25.4 mm is the standard top tube size, 28.6 mm (28.0 mm for French frames) is the standard for seat and down tubes. Some holders are available as adjustable clips that fit a large range of tube sizes.

Sachs Ergo Power Classic 8 Speed ErgoPower Brifter Shift/Brake Levers

£116.25 £155.00

✓ Original shifters - produced in the 1990s
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping

Sachs Ergo Power shift/brake levers, hailing from Germany and in production during the 1990s. Made from aluminium/rubber and weighing in at 522 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction setups you can in theory run any shifters with any speed setup.

Shift System - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting, for this to work correctly you must use the same shift system as your rear derailleur.

Shifter Type - brifters' are designed to be used on road drop type handlebars and 'trigger' shifters are designed to be used on flat bars, usually for mountain bikes.

Chainset Compatibility - the number of rings on the chainset the left shifter is capable of working with (providing the front derailleur is capable of the same).

Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible shift/brake levers. For traditional side pull calipers, cantilevers and mini V-brakes you’ll need shift/brake levers designed to be used with these as the cable pull is different.

Shimano 600 (MF-6151) c.1978 Vintage 5 Speed 13-17 Freewheel

£33.75 £45.00

✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & carefully cleaned
✓ Worldwide shipping

Shimano 600 freewheel, hailing from Japan and dating back to 1978. Made from steel and weighing in at 266 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong freewheel!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Speed - the number of cogs on the freewheel.

Range - the number of teeth on the smalles and largest cogs, this gives you an indication of how hard or easy the gearing will be, the lower the number the harder the gears. The tooth count of the cogs inbetween are usually evenly spaced, ie: a 6 speed 14-24 freewheel would likely have cog sizes 14, 16, 18, 20, 22 & 24.

Threading - this needs to match the thread of your rear hub. ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Hubs with a French thread must be used with a French threaded freewheel.

Stack Height - the total height (or width if you're looking at it when installed) of the freewheel, this is measured from the base (back of the largest cog) to the top (front of the smallest cog).

Chain width - this is mainly relevant for singlespeed and some older 3 or 4 speed freewheels - if this is ⅛” then you must use a ⅛” chain, but most freewheels (especially multiple speed ones) will use a standard 3/32” chain.

Regina Corsa c.1980 Vintage 5 Speed 14-20 Freewheel

£41.25 £55.00

✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & carefully cleaned
✓ Worldwide shipping

Regina Corsa freewheel, hailing from Italy and dating back to 1980. Made from steel and weighing in at 298 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong freewheel!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Speed - the number of cogs on the freewheel.

Range - the number of teeth on the smalles and largest cogs, this gives you an indication of how hard or easy the gearing will be, the lower the number the harder the gears. The tooth count of the cogs inbetween are usually evenly spaced, ie: a 6 speed 14-24 freewheel would likely have cog sizes 14, 16, 18, 20, 22 & 24.

Threading - this needs to match the thread of your rear hub. ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Hubs with a French thread must be used with a French threaded freewheel.

Stack Height - the total height (or width if you're looking at it when installed) of the freewheel, this is measured from the base (back of the largest cog) to the top (front of the smallest cog).

Chain width - this is mainly relevant for singlespeed and some older 3 or 4 speed freewheels - if this is ⅛” then you must use a ⅛” chain, but most freewheels (especially multiple speed ones) will use a standard 3/32” chain.

Shimano c.1996 Classic 6 Speed 14-24 Freewheel

£18.75 £25.00

✓ Original part - produced in the 1990s
✓ Professionally checked & carefully cleaned
✓ Worldwide shipping

Shimano freewheel, hailing from Japan and dating back to 1996. Made from steel and weighing in at 418 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Speed - the number of cogs on the freewheel.

Range - the number of teeth on the smalles and largest cogs, this gives you an indication of how hard or easy the gearing will be, the lower the number the harder the gears. The tooth count of the cogs inbetween are usually evenly spaced, ie: a 6 speed 14-24 freewheel would likely have cog sizes 14, 16, 18, 20, 22 & 24.

Threading - this needs to match the thread of your rear hub. ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Hubs with a French thread must be used with a French threaded freewheel.

Stack Height - the total height (or width if you're looking at it when installed) of the freewheel, this is measured from the base (back of the largest cog) to the top (front of the smallest cog).

Chain width - this is mainly relevant for singlespeed and some older 3 or 4 speed freewheels - if this is ⅛” then you must use a ⅛” chain, but most freewheels (especially multiple speed ones) will use a standard 3/32” chain.

Miche Vintage Quick Release Front Skewer

£17.00 £20.00

✓ Original skewer - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Miche front skewer, hailing from Italy and in production during the 1980s. Made from steel and weighing in at 82 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.

*Spacing - this should be within a few milimetres of your fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.

Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.

End nut length - the total length of the nut from end to end.

Shimano 600 6100 Series Vintage Quick Release Front Skewer

£14.88 £18.00

✓ Original skewer - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Shimano 600 front skewer, hailing from Japan and in production during the 1970s. Made from steel and weighing in at 100 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.

*Spacing - this should be within a few milimetres of your fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.

Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.

End nut length - the total length of the nut from end to end.

Campagnolo Nuovo Tipo/Gran Sport (1311) Vintage Quick Release Rear Skewer

£25.50 £30.00

✓ Original skewer - in production from the 1960s to the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Campagnolo Nuovo Tipo/Gran Sport rear skewer, hailing from Italy and in production from the 1960s to the 1970s. The design is of the ’pre-CPSC’ era produced until around 1978. Made from steel and weighing in at 78 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.

*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.

Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.

End nut length - the total length of the nut from end to end.

Campagnolo Nuovo Tipo/Gran Sport (1311) Vintage Quick Release Rear Skewer

£34.00 £40.00

✓ Original skewer - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Campagnolo Nuovo Tipo/Gran Sport rear skewer, hailing from Italy and in production during the 1980s. The design is of the ’post-CPSC’ era produced from around 1978 onwards. Made from steel and weighing in at 84 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.

*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.

Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.

End nut length - the total length of the nut from end to end.

Campagnolo Nuovo Tipo/Gran Sport (1311) Vintage Quick Release Rear Skewer

£25.50 £30.00

✓ Original skewer - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Campagnolo Nuovo Tipo/Gran Sport rear skewer, hailing from Italy and in production during the 1980s. The design is of the ’post-CPSC’ era produced from around 1978 onwards. Made from steel and weighing in at 84 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.

*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.

Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.

End nut length - the total length of the nut from end to end.

Miche Vintage Quick Release Rear Skewer

£17.00 £20.00

✓ Original skewer - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Miche rear skewer, hailing from Italy and in production during the 1980s. Made from steel and weighing in at 86 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.

*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.

Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.

End nut length - the total length of the nut from end to end.

Campagnolo Croce d' Aune (B500) Delta 1st Gen Vintage Centre Pull Brake Calipers

£296.25 £395.00

✓ Original parts - produced in the 1980s
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Croce d' Aune brake calipers, hailing from Italy and in production during the 1980s. Made from aluminium/steel and weighing in at 502 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

The brakes have been cleaned, thoroughly checked by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Condition - Very Good
Model ID - B500
Production Era - 1980s
Country - Italian
Material - Aluminium/Steel
Weight - 502 g
Stock Code - U-CP76V

TECHNICAL INFO

Caliper Type - Centre Pull
Front Brake Drop - 39 mm - 49 mm
Rear Brake Drop - 39 mm - 49 mm
Brake Fixing - Recessed Allen Key

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Caliper Type - side pull calipers (single or dual pivot) require nothing more than a brake hole to fix them to as the cable feeds straight into one of the arms, whereas centre pull calipers require a brazed-on or fitted cable hanger to allow the cable to be pulled from the centre.

Brake Drop - measured from the centre of the brake mounting hole to the centre of the wheel rim, measured in a straight line. Your measurement must be within the range of the caliper's given brake drop.

Brake Fixing - this refers to the way the brake is secured to the bike. For recessed allen key fixings the hole to the rear of the the fork crown/brake bridge should measure around 8mm, allowing the allen key head to be inserted and fixed to the brake bolt. External hex nut fixings require a hole of around 6mm, the hex nut is fixed to the protruding part of the brake bolt.

For a more detailed guide on getting the right brakes check out our journal.

Shimano Deore LX / Exage Mountain BB-M450 NOS Vintage English Thread Bottom Bracket Lockring

£11.88 £12.50

✓ Original BB lockring - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Shimano Deore LX / Exage Mountain bottom bracket lockring (or locking ring if you prefer), hailing from Japan and in production during the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 13 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bottom Bracket Thread Type - this must match the thread of your bottom bracket for the lockring to fit.

Thread Direction - most bottom brackets only have an adjustable cup on the non-driveside of the bike, so lockrings mostly thread to the right (clockwise), regardless of the thread type. However, some bottom brackets have adjustable cups on both sides so the thread direction may be different.

Thickness - this is rounded to the nearest 0.5 mm.

Zefal TX Switch NOS/NIB Classic Silver Telescopic Mini Bike Pump

£14.25 £15.00

✓ Original pump - produced in the 1990s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

Zefal TX Switch bicycle pump, hailing from France and in production during the 1990s (yet still new & unused after all this time). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR).

Product Manufacturer - Zefal SA, ZI Les Cailloux, 1 Route d’Ouvrouer, 45150 Jargeau, France

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.

Hutchinson Excel Kevlar Black/Red NOS Classic 700 x 20c Tyres

£46.75 £55.00

✓ Original pair of tyres - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Hutchinson Excel tyres, hailing from France and in production during the 1990s (yet still new & unused after all this time!). Made from rubber/kevlar and weighing in at 624 grams (the weight and price displayed are for a pair of tyres). A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Size - this is the manufacturer’s sizing and must match the size or your wheels. This can be confusing as tyres have had different sizing systems over the years, and there are many (sometimes conflicting) sizes available. For this reason it’s important to check the ISO diameter too for clarification, especially for 26” wheels.

Bike Type - the type of bike the tyres were designed to be used on. Road tyres will generally be narrow with minimal tread, touring tyres wider with a bit more grip in the tread, and cyclocross & MTB tyres wider still (especially the latter), with a much more pronounced tread pattern.

ISO Diameter - this relates to the diameter of the wheel rims at the point where the tyres are seated (bead seat diameter). This is a universal measurement, often displayed on tyres as 28-622 or similar, 28 referring to the tyre width and 622 being the ISO diameter in millimetres.

TPI - stands for threads per inch and refers to the thread count of the tyre casings. A high thread count usually means more supple and lighter tyres, this can be anything as high as 320 tpi. We can’t always provide this information however, as it’s not always possible to know for sure.

Kalloy Uno NOS Classic 130 mm 1 1/8" A-Head Stem

£18.75 £25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kalloy Uno ahead handlebar stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 213 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

3TTT THE NOS/NIB Classic 40 cm Anatomic Drop Handlebars

£27.00 £30.00

✓ Original bars - produced in the 2000s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

3TTT THE drop handlebars, hailing from Italy and in production during the 2000s. Made from aluminium and weighing in at 320 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Width (ctc)* - measured at the ends of the drops, from the centre of one side to the other (ctc), to the nearest cm. In some cases the bars may display a different width as some brands measure outside to outside rather than ctc, but we always use this measurement for consistency.

Shape - Classic' drops have a smooth curve, 'anatomic' have multiple angles for different hand positions, 'compact' are short reach with a shallow drop and randonneur bars are usually classic in shape but flare out at the drops.

Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.

Drop (ctc) - from the top flat section to the bottom of the drops, measured from the centre of one to the other with the flat part at the end of the drops parrallel to the ground.

Reach (ctc) - measured from the centre of the top section to the centre of the 'curve' at its furthest point, giving you the maximum reach. We measure this with the flat part at the end of of the drops parrallel to the ground.

Cable Groove - these allow you to run your cables neatly underneath the handlebar tape, if your setup requires this.

WTB Velociraptor Front Black/Skin NOS Classic 26 x 2.1" MTB Folding Tyre

£29.25 £32.50

✓ Original tyre - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

WTB Velociraptor folding tyre, hailing from the United States and in production during the 1990s (yet still new & unused after all this time!). Made from rubber and weighing in at 665 grams (the weight and price displayed are for one tyre, if we have more in stock you'll be able to add them to your basket). A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

NB: If mounted in the photos this is for illustrative purpose only, any wheels or rims shown are not included.

OVERVIEW

Condition - New Old Stock*
Condition Notes - Some cracks on the tread area (see last photo) due to age.
Production Era - 1990s
Country - American
Material - Rubber
Weight - 665 g
Stock Code - D-TY-F24C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Size - 26 x 2.1"
Bike Type - MTB
ISO Diameter - 559 mm (26")

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Size - this is the manufacturer’s sizing and must match the size or your wheel. This can be confusing as tyres have had different sizing systems over the years, and there are many (sometimes conflicting) sizes available. For this reason it’s important to check the ISO diameter too for clarification, especially for 26” wheels.

Bike Type - the type of bike the tyre was designed to be used on. Road tyres will generally be narrow with minimal tread, touring tyres wider with a bit more grip in the tread, and cyclocross & MTB tyres wider still (especially the latter), with a much more pronounced tread pattern.

ISO Diameter - this relates to the diameter of the wheel rim at the point where the tyre is seated (bead seat diameter). This is a universal measurement, often displayed on tyres as 28-622 or similar, 28 referring to the tyre width and 622 being the ISO diameter in millimetres.

TPI - stands for threads per inch and refers to the thread count of the tyre casing. A high thread count usually means a more supple and lighter tyre, this can be anything as high as 320 tpi. We can’t always provide this information however, as it’s not always possible to know for sure.

Campagnolo C-Record (4035/A) 1st Gen NOS Vintage 3/16" Steel Bottom Bracket Bearings

£28.50 £30.00

✓ Original BB bearings - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Campagnolo C-Record caged bottom bracket bearing set (or ball races if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

The first C-Record bottom brackets used 3/16” bearings like the earlier Super Record titanium models. These bearings are compatible with both models as they're identical in spec.

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bearings!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bearing Size - most bottom brackets use 1/4" bearings, but there are some that use smaller sizes so it's advisable to measure your old ones or check with a local bike shop to be sure.

Retainer Type - you can use any type of retaining cage in any bottom bracket as long as the bearing sizes are correct.

Shimano Dura-Ace (137 9001) 1st Gen GB-100 NOS Vintage 1/4" Steel Bottom Bracket Bearings

£14.25 £15.00

✓ Original BB bearings - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Shimano Dura-Ace caged bottom bracket bearing set (or ball races if you prefer), hailing from Japan and in production during the 1970s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bearings!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bearing Size - most bottom brackets use 1/4" bearings, but there are some that use smaller sizes so it's advisable to measure your old ones or check with a local bike shop to be sure.

Retainer Type - you can use any type of retaining cage in any bottom bracket as long as the bearing sizes are correct.

Sakae/Ringyo (SR) Royal / Super Apex NOS Vintage 1/4" Steel Bottom Bracket Bearings

£11.88 £12.50

✓ Original BB bearings - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Sakae/Ringyo (SR) Royal / Super Apex caged bottom bracket bearing set (or ball races if you prefer), hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bearings!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bearing Size - most bottom brackets use 1/4" bearings, but there are some that use smaller sizes so it's advisable to measure your old ones or check with a local bike shop to be sure.

Retainer Type - you can use any type of retaining cage in any bottom bracket as long as the bearing sizes are correct.

Shimano 105 SC / Deore LX (188 9802) NOS/NIB Vintage 1/4" Steel Bottom Bracket Bearings

£14.25 £15.00

✓ Original BB bearings - in production from the 1980s to the 1990s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Shimano 105 SC / Deore LX caged bottom bracket bearing set (or ball races if you prefer), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bearings!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bearing Size - most bottom brackets use 1/4" bearings, but there are some that use smaller sizes so it's advisable to measure your old ones or check with a local bike shop to be sure.

Retainer Type - you can use any type of retaining cage in any bottom bracket as long as the bearing sizes are correct.

Shimano Dura-Ace / 600 (137 0500) NOS Vintage English Thread Bottom Bracket Lockring

£19.00 £20.00

✓ Original BB lockring - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Shimano Dura-Ace / 600 bottom bracket lockring (or locking ring if you prefer), hailing from Japan and in production during the 1970s (yet still new & unused after all this time). Made from steel and weighing in at 14 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong lockring

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bottom Bracket Thread Type - this must match the thread of your bottom bracket for the lockring to fit.

Thread Direction - most bottom brackets only have an adjustable cup on the non-driveside of the bike, so lockrings mostly thread to the right (clockwise), regardless of the thread type. However, some bottom brackets have adjustable cups on both sides so the thread direction may be different.

Thickness - this is rounded to the nearest 0.5 mm.

Sugino Royal NOS Vintage English Thread Bottom Bracket Lockring

£19.00 £20.00

✓ Original BB lockring - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Sugino Royal bottom bracket lockring (or locking ring if you prefer), hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 12 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong lockring

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

Product Manufacturer - 2880 Kuriyama, Namerikawa City, Toyama Prefecture, 936-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bottom Bracket Thread Type - this must match the thread of your bottom bracket for the lockring to fit.

Thread Direction - most bottom brackets only have an adjustable cup on the non-driveside of the bike, so lockrings mostly thread to the right (clockwise), regardless of the thread type. However, some bottom brackets have adjustable cups on both sides so the thread direction may be different.

Thickness - this is rounded to the nearest 0.5 mm.

Sakae/Ringyo (SR) Super Apex NOS Vintage English Thread Bottom Bracket Lockring

£14.25 £15.00

✓ Original BB lockring - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Sakae/Ringyo (SR) Super Apex bottom bracket lockring (or locking ring if you prefer), hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 16 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong lockring

OVERVIEW

TECHNICAL INFO