All Sale Items

Shimano Crane DB100 Dura-Ace 1st Gen NOS Vintage 9T Jockey Wheels

£19.00 £20.00

✓ Original jockey wheels - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Shimano Crane jockey wheels (or derailleur pulleys if you prefer), hailing from Japan and in production during the 1970s (yet still new & unused after all this time). Made from steel and weighing in at 39 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the jockey wheels!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Teeth - the tooth count has increased with the introduction of more gears, but this happened very gradually so 10 tooth jockey wheels were standard for a very long time.

*Compatible Speed - the number of cogs the jockey wheels were designed to be used with. When using derailleurs for indexed shifting it's important to stick to this, but friction shifting is much more forgiving so you're unlikely to have any problems using the next speed up or down, providing all the measurements are correct.

Diameter (OD) - the diameter of the jockey wheels, from the outside edge of the teeth. It’s important to stay close to the ones you're replacing to ensure they fit.

Thickness - measured at the widest point, by the centre hole. The spacing has generally become narrower over the years to accommodate more gears.

Centre Hole (ID) - the inside diameter (usually inside the bushing/spacer if present). This rarely presents a problem, but some older jockey wheels have a different diameter so it's worth double checking.

Campagnolo C-Record White / Grey NOS Vintage 10T Jockey Wheels

£38.00 £40.00

✓ Original jockey wheels - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Campagnolo C-Record jockey wheels (or derailleur pulleys if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time). Made from plastic and weighing in at 12 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

These work with all Campagnolo 7/8 speed rear derailleurs from the same era, including Croce D'Aune, Chorus, Athena etc.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the jockey wheels!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Teeth - the tooth count has increased with the introduction of more gears, but this happened very gradually so 10 tooth jockey wheels were standard for a very long time.

*Compatible Speed - the number of cogs the jockey wheels were designed to be used with. When using derailleurs for indexed shifting it's important to stick to this, but friction shifting is much more forgiving so you're unlikely to have any problems using the next speed up or down, providing all the measurements are correct.

Diameter (OD) - the diameter of the jockey wheels, from the outside edge of the teeth. It’s important to stay close to the ones you're replacing to ensure they fit.

Thickness - measured at the widest point, by the centre hole. The spacing has generally become narrower over the years to accommodate more gears.

Centre Hole (ID) - the inside diameter (usually inside the bushing/spacer if present). This rarely presents a problem, but some older jockey wheels have a different diameter so it's worth double checking.

55.5cm Hetchins Italia c.1975 Vintage British Steel Road Bike Frame Set

£535.50 £595.00

✓ Original vintage frame - built in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked over & photographed in detail
✓ Worldwide shipping

Perhaps one of the best-known of all British classic lightweight builders, Hetchins constructed their instantly recognised, elaborately lugged frames for over 60 years. Hyman Hetchins had a gramophone and cycle accessories shop in Tottenham in the 1920s, and by the 1930s, he was producing frames bearing the shop’s name. At this point, a partnership with one of his frame-builders, Jack Denny, was started, and a patent for vibrant rear stays was applied for. The curved shape of the rear stays was said to improve comfort on Britain’s rough roads; it also had the benefit of being easily distinguishable as a Hetchins-built frame, even from a distance. As well as the vibrant (or curly) rear end, Hetchins offered a huge range of frames, often with highly ornamental, heavily modified lugs, all with the option to further customise the final frame. The brand received further coverage with a successful export business into the burgeoning US market, where they are now highly collectible.

Though lacking the ornate lugs or shaped stays that other Hetchins sport, the Italia was a very finely made road frame designed to compete with the best Italian builders of the time. There were two versions of the Italia produced, with some made by a contractor in Italy from Columbus tubes, but the majority made in the Hetchins workshop from Reynolds 531. Built with shaped and filed Prugnat lugs and lightweight tubes, the frames normally featured the Italianate-style seat stay/seat tube junction and a more continental-style fork crown rather than Hetchins' twin-plate design. Like all hand-built, custom-order frames coming out of the Hetchins workshop, though, anything was possible, and there are many small variations and special features even on this supposedly simple frame.

This mid-1970s model Italia was probably built just after the shop moved to Southend, though it still sports the Tottenham address on the decals. Though less showy than some of the intricately lugged frames that were coming out of the workshop at the time, this frame still features carefully cut Prugnat lugs and a fork crown. This is a made-in-the-UK Reynolds 531 version of the Italia, which we believe still has its original paint and decals. Likely designed as a winter or training bike, the frame set has mudguard braze-ons and rear brake routing designed for a centre-pull brake.

If you're taking part in L'Eroica or a similar vintage event, this frame is of the correct age, so you won't be disqualified for being a rule breaker!

OVERVIEW

SIZING

Size Guide* - Medium (Approx 32 1/2" Inside Leg)
Seat Tube (ctc) - 55.5 cm
Top Tube (ctc) - 56 cm
Head Tube - 137 mm
Chainstay Length - 42 cm
Wheelbase - 99.5 cm

*This is just a guide, not a guarantee the frame will fit as every rider is different. If you're unsure of your size we'd always recommend trying out a bike with similar frame dimensions first.

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Seat Tube (ctc) - we measure from the centre of the bottom bracket shell up to the centre line of the top tube to give a consistent measurement regardless of frame design (ctc means centre to centre).

Top Tube (ctc) - this is measured from the centre of the head tube to the centre of the seat tube, along the centre of the top tube.

Chainstay Length - measured from the centre of the bottom bracket shell to the centre point of the rear dropout.

Wheelbase - measured from the centre of the front fork dropout to the centre point of the rear dropout.

Front & Rear Spacing - measured from the inside of one dropout to the other. The dropouts on steel frames can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon frames should never be stretched.

Brake Drop - measured using wheels of the relevant size for the frame, as stated in the technical info section.

Headset Threads - although it's generally recommended to match threaded parts exactly, with headsets you can technically mix and match, unless you have French or the obscure old Raleigh threads, in which case you need to stick to that type.

55cm Edison Vintage British Steel Road Bike Frame Set

£328.50 £365.00

✓ Original vintage frame - built in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked over & photographed in detail
✓ Worldwide shipping

Former Carlton frame-builders Eddie and Chris Hazlehurst were not widely known outside of their native Derbyshire but built a small quantity of quality frames through the '80s and '90s. The name Edison came from 'Eddie and son,' and though there are not many surviving examples of their work built at their shop in Clowne, those that remain are well regarded.

This rare 1980s Edison frame is of lovely quality and built from Reynolds 531c lightweight tubing and long-point lugs with Carlton-esque semi-wrapped seat stays. Very light at just over 2.5 kg for a 55cm frame, this would have been a top-end custom bike in its day. With a striking blue-to-white-to-red fade paint job over chromed dropouts, it is in great condition and ready to be built up and ridden.

If you're taking part in L'Eroica or a similar vintage event, this frame is of the correct age, so you won't be disqualified for being a rule breaker!

OVERVIEW

SIZING

Size Guide* - Medium (Approx 32 1/2" Inside Leg)
Seat Tube (ctc) - 55 cm
Top Tube (ctc) - 55 cm
Head Tube - 148 mm
Chainstay Length - 40.5 cm
Wheelbase - 97.5 cm

*This is just a guide, not a guarantee the frame will fit as every rider is different. If you're unsure of your size we'd always recommend trying out a bike with similar frame dimensions first.

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Seat Tube (ctc) - we measure from the centre of the bottom bracket shell up to the centre line of the top tube to give a consistent measurement regardless of frame design (ctc means centre to centre).

Top Tube (ctc) - this is measured from the centre of the head tube to the centre of the seat tube, along the centre of the top tube.

Chainstay Length - measured from the centre of the bottom bracket shell to the centre point of the rear dropout.

Wheelbase - measured from the centre of the front fork dropout to the centre point of the rear dropout.

Front & Rear Spacing - measured from the inside of one dropout to the other. The dropouts on steel frames can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon frames should never be stretched.

Brake Drop - measured using wheels of the relevant size for the frame, as stated in the technical info section.

Headset Threads - although it's generally recommended to match threaded parts exactly, with headsets you can technically mix and match, unless you have French or the obscure old Raleigh threads, in which case you need to stick to that type.

54cm Fanini Super Vintage Italian Steel Road Bike Frame Set

£405.00 £450.00

✓ Original vintage frame - built in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked over & photographed in detail
✓ Worldwide shipping

Fanini are a true cycling family: promotors; sponsors; team owners; sales reps; manufacturers, and amongst all of this they produced some magnificent hand built bikes. Often equal parts work of art to pure performance, Fanini built bikes that showed what Italian craftsmanship and flair could achieve. Frequently sporting Campagnolo's top end groupsets and a red paintjob, Fanini were built in low numbers throughout the 70s and 80s and are now rather rare to find.

A beautifully understated 1970s lightweight road frame from Fanini, probably made with Columbus SL tubes. Finely detailed hand-cut lugs and a slotted bottom bracket were typical of the artisanal approach to frame-building at Fanini and helped keep the weight down. The metallic burgundy paint job looks to have newer decals applied over the clear coat, and aside from some marks, is in lovely usable condition.

If you're taking part in L'Eroica or a similar vintage event, this frame is of the correct age, so you won't be disqualified for being a rule breaker!

OVERVIEW

SIZING

Size Guide* - Medium (Approx 32" Inside Leg)
Seat Tube (ctc) - 54 cm
Top Tube (ctc) - 54 cm
Head Tube - 133 mm
Chainstay Length - 40.5 cm
Wheelbase - 98.5 cm

*This is just a guide, not a guarantee the frame will fit as every rider is different. If you're unsure of your size we'd always recommend trying out a bike with similar frame dimensions first.

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Seat Tube (ctc) - we measure from the centre of the bottom bracket shell up to the centre line of the top tube to give a consistent measurement regardless of frame design (ctc means centre to centre).

Top Tube (ctc) - this is measured from the centre of the head tube to the centre of the seat tube, along the centre of the top tube.

Chainstay Length - measured from the centre of the bottom bracket shell to the centre point of the rear dropout.

Wheelbase - measured from the centre of the front fork dropout to the centre point of the rear dropout.

Front & Rear Spacing - measured from the inside of one dropout to the other. The dropouts on steel frames can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon frames should never be stretched.

Brake Drop - measured using wheels of the relevant size for the frame, as stated in the technical info section.

Headset Threads - although it's generally recommended to match threaded parts exactly, with headsets you can technically mix and match, unless you have French or the obscure old Raleigh threads, in which case you need to stick to that type.

Tange NA NOS Vintage English Bottom Bracket Cups

£28.50 £30.00

✓ Original parts - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Tange left and right bottom bracket cup set, hailing from Japan and in production during the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 112 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong BB cups!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - TANGE International Co. Ltd, No.483, Minyi St, Xiushui Township, Changhua County 50444,Taiwan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bottom Bracket Type - ‘square taper’, as the name suggests have square shaped axle ends that slot into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system.

Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing cups, they often have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.

Campagnolo C-Record (1134019) 2nd Gen NOS/NIB Vintage 7/32" Steel Caged Bottom Bracket Bearings

£28.50 £30.00

✓ Original BB bearings - produced in the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Campagnolo C-Record caged bottom bracket bearing set (or ball races if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

Initially, C-Record bottom brackets used 3/16” bearings like the earlier Super Record models, but they changed to these 7/32" ones in the late 1980s.

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bearings!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bearing Size - most bottom brackets use 1/4" bearings, but there are some that use smaller sizes so it's advisable to measure your old ones or check with a local bike shop to be sure.

Retainer Type - you can use any type of retaining cage in any bottom bracket as long as the bearing sizes are correct.

Shimano Dura-Ace (BB-7400) NJS c.1987 Vintage English 112 mm Bottom Bracket

£137.75 £145.00

✓ Original part - in production from the 1980s to the 1990s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Shimano Dura-Ace bottom bracket (or BB for short), hailing from Japan and dating back to 1987. Made from steel and weighing in at 310 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bottom bracket!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing a bottom bracket the cups should have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.

Axle Length - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing a bottom bracket that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.

Axle Type - you can tell which type of axle you need by looking at the shape of the bottom bracket hole in your crankset. For square tapers, the ISO introduced a standard for European makers in the early 90s, JIS then did the same in Asia. Before then it was not so simple, and although there is a degree of interchangeability, the best way to make sure you have the right axle is to stick to the same brand from the same era, ideally the proprietary model.

Gipiemme Sprint (200DS) Strada Vintage Italian 113 mm Bottom Bracket

£38.00 £40.00

✓ Original part - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Gipiemme Sprint bottom bracket (or BB for short), hailing from Italy and in production during the 1980s. Made from steel and weighing in at 325 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bottom bracket!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing a bottom bracket the cups should have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.

Axle Length - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing a bottom bracket that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.

Axle Type - you can tell which type of axle you need by looking at the shape of the bottom bracket hole in your crankset. For square tapers, the ISO introduced a standard for European makers in the early 90s, JIS then did the same in Asia. Before then it was not so simple, and although there is a degree of interchangeability, the best way to make sure you have the right axle is to stick to the same brand from the same era, ideally the proprietary model.

Campagnolo Super Record (4001) 1st Gen c.1977 Vintage Rear Derailleur

£251.75 £265.00

✓ Original part - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Super Record rear derailleur (or mech if you prefer), hailing from Italy and dating back to 1977. Made from aluminium/steel/titanium and weighing in at 180 grams - incredibly lightweight for a rear derailleur at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong rear mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Shifting system - friction means your gear levers don't click when you change gear, when they do click it's referred to as indexed shifting. If you have indexed gear levers they must use the same system as the rear derailleur, if you're using friction levers you can mix and match.

Speed - the number of cogs at the back the derailleur was designed to be used with. This is important with indexed shifting, but with friction shifters you can in theory run any rear mech with any number of cogs, but you are more likely to have issues running high numbers of cogs with mechs from earlier eras.

Max cog size - the amount of teeth on the largest cog of your freewheel/cassette can be no greater than this to work with this derailleur.

Chain wrap - subtract the size of your smallest rear cog from your biggest, then do the same with your chainrings, add the 2 numbers together and you have your chain wrap.

Chain width - generally speaking, derailleurs designed for more than 3 speed use will fit a standard 3/32'' chain, the exception being some Cyclo & Simplex models from around the mid 1900s.

Shimano Dura-Ace (RD-7400) c.1986 Vintage Rear Derailleur

£90.25 £95.00

✓ Original part - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Shimano Dura-Ace rear derailleur (or mech if you prefer), hailing from Japan and dating back to 1986. Made from aluminium/steel and weighing in at 200 grams - pretty lightweight for a rear derailleur at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong rear mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Shifting system - friction means your gear levers don't click when you change gear, when they do click it's referred to as indexed shifting. If you have indexed gear levers they must use the same system as the rear derailleur, if you're using friction levers you can mix and match.

Speed - the number of cogs at the back the derailleur was designed to be used with. This is important with indexed shifting, but with friction shifters you can in theory run any rear mech with any number of cogs, but you are more likely to have issues running high numbers of cogs with mechs from earlier eras.

Max cog size - the amount of teeth on the largest cog of your freewheel/cassette can be no greater than this to work with this derailleur.

Chain wrap - subtract the size of your smallest rear cog from your biggest, then do the same with your chainrings, add the 2 numbers together and you have your chain wrap.

Chain width - generally speaking, derailleurs designed for more than 3 speed use will fit a standard 3/32'' chain, the exception being some Cyclo & Simplex models from around the mid 1900s.

Huret Duopar (Ref 2648) Titanium Vintage Rear Derailleur

£166.25 £175.00

✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Huret Duopar rear derailleur (or mech if you prefer), hailing from France and in production from the 1970s to the 1980s. Made from titanium/aluminium/ steel and weighing in at 256 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong rear mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Shifting system - friction means your gear levers don't click when you change gear, when they do click it's referred to as indexed shifting. If you have indexed gear levers they must use the same system as the rear derailleur, if you're using friction levers you can mix and match.

Speed - the number of cogs at the back the derailleur was designed to be used with. This is important with indexed shifting, but with friction shifters you can in theory run any rear mech with any number of cogs, but you are more likely to have issues running high numbers of cogs with mechs from earlier eras.

Max cog size - the amount of teeth on the largest cog of your freewheel/cassette can be no greater than this to work with this derailleur.

Chain wrap - subtract the size of your smallest rear cog from your biggest, then do the same with your chainrings, add the 2 numbers together and you have your chain wrap.

Chain width - generally speaking, derailleurs designed for more than 3 speed use will fit a standard 3/32'' chain, the exception being some Cyclo & Simplex models from around the mid 1900s.

REG 320 NOS Vintage Bottom Bracket Dust Sleeve

£17.58 £18.50

✓ Original BB sleeve - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

REG 320 BB barrel sleeve protector (or cover, or seal, or shield, or boot!), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time). A fine choice for keeping your vintage bike's bottom bracket free from dust and water, but great for all bikes with cup & cone BBs as the sleeves are all a standard size.

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong BB sleeve!

OVERVIEW

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR).

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

Regina Extra CX NOS/NIB Vintage 6 Speed 13-23 Freewheel

£117.00 £130.00

✓ Original part - produced in the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Regina Extra CX freewheel, hailing from Italy and in production during the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 412 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong freewheel!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR).

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Speed - the number of cogs on the freewheel.

Range - the number of teeth on the smalles and largest cogs, this gives you an indication of how hard or easy the gearing will be, the lower the number the harder the gears. The tooth count of the cogs inbetween are usually evenly spaced, ie: a 6 speed 14-24 freewheel would likely have cog sizes 14, 16, 18, 20, 22 & 24.

Threading - this needs to match the thread of your rear hub. ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Hubs with a French thread must be used with a French threaded freewheel.

Stack Height - the total height (or width if you're looking at it when installed) that the freewheel will require once installed, including any protruding body parts such as base plates.

Overall Sprocket Spacing - this is measured from the outside of the first cog to the outside of the last cog.

Chain Width - this is mainly relevant for singlespeed and some older 3 or 4 speed freewheels - if this is ⅛” then you must use a ⅛” chain, but most freewheels (especially multiple speed ones) will use a standard 3/32” chain.

Shimano Dura-Ace (MF-7400) c.1987 Vintage 7 Speed 12-18 Freewheel

£71.25 £75.00

✓ Original part - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & carefully cleaned
✓ Worldwide shipping

Shimano Dura-Ace freewheel, hailing from Japan and dating back to 1987. Made from steel and weighing in at 334 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong freewheel!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR).

Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Speed - the number of cogs on the freewheel.

Range - the number of teeth on the smalles and largest cogs, this gives you an indication of how hard or easy the gearing will be, the lower the number the harder the gears. The tooth count of the cogs inbetween are usually evenly spaced, ie: a 6 speed 14-24 freewheel would likely have cog sizes 14, 16, 18, 20, 22 & 24.

Threading - this needs to match the thread of your rear hub. ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Hubs with a French thread must be used with a French threaded freewheel.

Stack Height - the total height (or width if you're looking at it when installed) that the freewheel will require once installed, including any protruding body parts such as base plates.

Overall Sprocket Spacing - this is measured from the outside of the first cog to the outside of the last cog.

Chain Width - this is mainly relevant for singlespeed and some older 3 or 4 speed freewheels - if this is ⅛” then you must use a ⅛” chain, but most freewheels (especially multiple speed ones) will use a standard 3/32” chain.

Campagnolo C-Record (A040) 2nd Type Vintage 170 mm Road Chainset

£166.25 £175.00

✓ Original part - in production from the 1980s to the 1990s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo C-Record chainset (or crankset, if you prefer), hailing from Italy and in production from the 1980s to the 1990s. Made from aluminium and weighing in at 675 grams - pretty lightweight for a chainset at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Chainring Count - the number of chainrings on the chainset. Fixed gear track bikes, single-speeds and some geared bikes use a single chainring, road bikes commonly use a double (two rings) and most touring bikes and mountain bikes will use a triple chainset (three rings).

Tooth Count - the number of teeth on the chainring(s), the higher the number the harder the gear.

Bottom Bracket Type - ‘square taper’, as the name suggests have a square shaped axle that slots into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a chainset that matches.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is only really needed when changing chainrings. To calculate the BCD, measure the distance in millimeters from the centre of any chainring bolt to the centre of an adjacent one and multiply it by 1.709 (you’ll likely need to round the resulting number up or down a little to get your BCD measurement).

Crank Arm Length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.

Chain Width - this is mostly only relevant for chainsets with a single chainring - if this is ⅛” then you must use a ⅛” chain. Almost all double and triple (and some single) ring chainsets will use a standard 3/32” chain, the only exception being old chainsets designed for 3 or 4 speed freewheels.

Pedal Threads - this must match the thread of your pedals and is usually stamped on the pedals themselves, most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

*Intended Speed - the number of cogs at the back the chainset was designed to be used with. We refer to it as ‘intended’ speed as most double and triple chainsets will actually work with different speeds than originally intended, but the further away you get from the intended speed the more likely you are to experience minor setup issues. The exception being some chainsets intended for 10 speed use or higher, with these it’s better to stick to the intended speed.

*Bike Type - this is just a guide, any chainset can technically be used on any bike as long as everything's compatible.

Campagnolo Record (1052/1) 3rd Gen Vintage Clamp-On 28.6 mm Front Derailleur

£118.75 £125.00

✓ Original part - in production from the 1960s to the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Record front derailleur (or mech, or changer if you prefer), hailing from Italy and in production from the 1960s to the 1970s. Made from aluminium/steel and weighing in at 93 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

This is an unusal example of the Record front mech, with all the features of the 3rd gen version, but with the later triangular arms and circlip usually seen on the 6th gen Super Record era variation from the early 1970s.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Campagnolo Record (1052/1) 3rd Gen v2 Vintage Clamp-On 28.6 mm Front Derailleur

£104.50 £110.00

✓ Original part - produced in the 1960s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Record front derailleur (or mech, or changer if you prefer), hailing from Italy and in production during the 1960s. Made from aluminium/steel and weighing in at 94 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Campagnolo Record (1052/1) 3rd Gen v2 Vintage Clamp-On 28.6 mm Front Derailleur

£109.25 £115.00

✓ Original part - produced in the 1960s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Record front derailleur (or mech, or changer if you prefer), hailing from Italy and in production during the 1960s. Made from aluminium/steel and weighing in at 94 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Shimano 600 EX (FD-6207) c.1985 Vintage Clamp-On 28.6 mm Front Derailleur

£38.00 £40.00

✓ Original part - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Shimano 600 EX front derailleur (or mech, or changer if you prefer), hailing from Japan and dating back to 1985. Made from aluminium/steel and weighing in at 114 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Shimano Dura-Ace (FD-7400) Vintage Clamp-On 28.6 mm Front Derailleur

£118.75 £125.00

✓ Original part - in production from the 1980s to the 1990s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Shimano Dura-Ace front derailleur (or mech, or changer if you prefer), hailing from Japan and in production from the 1980s to the 1990s. Made from aluminium/steel and weighing in at 95 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - Shimano Inc. 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Campagnolo Super Record (1052/SR / 0104011) Vintage Braze-On Front Derailleur

£80.75 £85.00

✓ Original part - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Super Record front derailleur (or mech, or changer if you prefer), hailing from Italy and in production during the 1980s. Made from aluminium/steel and weighing in at 94 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Campagnolo Nuovo/Super Record (1052/BZ) 11th Gen Vintage Braze-On Front Derailleur

£71.25 £75.00

✓ Original part - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Nuovo/Super Record front derailleur (or mech, or changer if you prefer), hailing from Italy and in production during the 1980s. Made from aluminium/steel and weighing in at 92 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Campagnolo Nuovo/Super Record (1052/BZ) 11th Gen Vintage Braze-On Front Derailleur

£61.75 £65.00

✓ Original part - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Nuovo/Super Record front derailleur (or mech, or changer if you prefer), hailing from Italy and in production during the 1980s. Made from aluminium/steel and weighing in at 94 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Campagnolo Nuovo/Super Record (1014) Vintage Clamp-On Downtube Shifters

£52.25 £55.00

✓ Original shifters - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Nuovo/Super Record down tube shifters (or gear levers if you prefer), hailing from Italy and in production during the 1970s. Made from aluminium/steel and weighing in at 69 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifters!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Fixing Type - if you have small mounts on either side of the frame’s down tube you need braze-on shifters, if there are no mounts you’ll need clamp-on (sometimes referred to as band-on). Some 'aero' frames have mounts fixed to the top of the down tube, for these frames you require top mount shifters for the correct boss type (see below). There are also 'Clamp-Over' shifters that allow front & rear shifters to be used on a frame that only has a single braze-on.

Shift Type - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting. For this to work correctly you must use the same system as your rear derailleur, if you're using friction levers you can mix and match. You don't need to worry about the front derailleur as left downtube shifters aren't indexed.

Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction shifters you can in theory run any shifters with any speed setup, although the right lever will need to be pulled back further to shift into the larger cogs.

Shifter Boss Type - the shape of the mount (for braze-on fixings only). Campagnolo / ISO is standard and easily identified by the flat sections on either side, usually combined with a square base for the backing stop plates to fit. There are also Shimano ones with a keyhole shaped base and much less common French ones that are round with no flat sections.

Boss Thread Size - M5 (5 mm) is standard for Campagnolo / ISO bosses, but Shimano bosses will often have M4.5 (4.5 mm) threads and the French bosses would likely have 5 x 1 mm threads.

Simplex Silver Range (SJ 6211) Touring Vintage Clamp-On Downtube Shifters

£33.25 £35.00

✓ Original shifters - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Simplex Silver Range down tube shifters (or gear levers if you prefer), hailing from France and in production during the 1980s. Made from aluminium/steel and weighing in at 110 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifters!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Fixing Type - if you have small mounts on either side of the frame’s down tube you need braze-on shifters, if there are no mounts you’ll need clamp-on (sometimes referred to as band-on). Some 'aero' frames have mounts fixed to the top of the down tube, for these frames you require top mount shifters for the correct boss type (see below). There are also 'Clamp-Over' shifters that allow front & rear shifters to be used on a frame that only has a single braze-on.

Shift Type - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting. For this to work correctly you must use the same system as your rear derailleur, if you're using friction levers you can mix and match. You don't need to worry about the front derailleur as left downtube shifters aren't indexed.

Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction shifters you can in theory run any shifters with any speed setup, although the right lever will need to be pulled back further to shift into the larger cogs.

Shifter Boss Type - the shape of the mount (for braze-on fixings only). Campagnolo / ISO is standard and easily identified by the flat sections on either side, usually combined with a square base for the backing stop plates to fit. There are also Shimano ones with a keyhole shaped base and much less common French ones that are round with no flat sections.

Boss Thread Size - M5 (5 mm) is standard for Campagnolo / ISO bosses, but Shimano bosses will often have M4.5 (4.5 mm) threads and the French bosses would likely have 5 x 1 mm threads.

Campagnolo Nuovo/Super Record (1013/5N / 1013/6N) Vintage Braze-on Downtube Shifters

£52.25 £55.00

✓ Original shifters - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Nuovo/Super Record down tube shifters (or gear levers if you prefer), hailing from Italy and in production during the 1980s. Made from aluminium/steel and weighing in at 42 grams - incredibly lightweight for downtube shifters at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifters!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Fixing Type - if you have small mounts on either side of the frame’s down tube you need braze-on shifters, if there are no mounts you’ll need clamp-on (sometimes referred to as band-on). Some 'aero' frames have mounts fixed to the top of the down tube, for these frames you require top mount shifters for the correct boss type (see below). There are also 'Clamp-Over' shifters that allow front & rear shifters to be used on a frame that only has a single braze-on.

Shift Type - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting. For this to work correctly you must use the same system as your rear derailleur, if you're using friction levers you can mix and match. You don't need to worry about the front derailleur as left downtube shifters aren't indexed.

Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction shifters you can in theory run any shifters with any speed setup, although the right lever will need to be pulled back further to shift into the larger cogs.

Shifter Boss Type - the shape of the mount (for braze-on fixings only). Campagnolo / ISO is standard and easily identified by the flat sections on either side, usually combined with a square base for the backing stop plates to fit. There are also Shimano ones with a keyhole shaped base and much less common French ones that are round with no flat sections.

Boss Thread Size - M5 (5 mm) is standard for Campagnolo / ISO bosses, but Shimano bosses will often have M4.5 (4.5 mm) threads and the French bosses would likely have 5 x 1 mm threads.

Campagnolo Nuovo/Super Record (1013/5 / 1013/6) Vintage Braze-on Downtube Shifters

£47.50 £50.00

✓ Original shifters - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Nuovo/Super Record down tube shifters (or gear levers if you prefer), hailing from Italy and in production from the 1970s to the 1980s. Made from aluminium/steel and weighing in at 41 grams - incredibly lightweight for downtube shifters at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifters!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Fixing Type - if you have small mounts on either side of the frame’s down tube you need braze-on shifters, if there are no mounts you’ll need clamp-on (sometimes referred to as band-on). Some 'aero' frames have mounts fixed to the top of the down tube, for these frames you require top mount shifters for the correct boss type (see below). There are also 'Clamp-Over' shifters that allow front & rear shifters to be used on a frame that only has a single braze-on.

Shift Type - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting. For this to work correctly you must use the same system as your rear derailleur, if you're using friction levers you can mix and match. You don't need to worry about the front derailleur as left downtube shifters aren't indexed.

Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction shifters you can in theory run any shifters with any speed setup, although the right lever will need to be pulled back further to shift into the larger cogs.

Shifter Boss Type - the shape of the mount (for braze-on fixings only). Campagnolo / ISO is standard and easily identified by the flat sections on either side, usually combined with a square base for the backing stop plates to fit. There are also Shimano ones with a keyhole shaped base and much less common French ones that are round with no flat sections.

Boss Thread Size - M5 (5 mm) is standard for Campagnolo / ISO bosses, but Shimano bosses will often have M4.5 (4.5 mm) threads and the French bosses would likely have 5 x 1 mm threads.

Campagnolo Nuovo Record (2040/1) Short Reach Vintage Brake Calipers

£128.25 £135.00

✓ Original parts - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Campagnolo Nuovo Record brake calipers, hailing from Italy and in production from the 1970s to the 1980s. The design is of the ’post-CPSC’ era produced from around 1978 onwards. Made from aluminium/steel and weighing in at 382 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong brakes!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are strongly recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Caliper Type - side pull calipers (single or dual pivot) require nothing more than a brake hole to fix them to as the cable feeds straight into one of the arms, whereas centre pull calipers require a brazed-on or fitted cable hanger to allow the cable to be pulled from the centre.

Brake Drop - measured from the centre of the brake mounting hole to the centre of the wheel rim in a straight line. Your measurement must be well within the range of the caliper's given brake drop to allow the brakes to have good contact with the rim's braking surface.

Brake Fixing - this refers to the way the brake is secured to the bike. For recessed allen key fixings the hole to the rear of the the fork crown/brake bridge should measure around 8mm, allowing the allen key head to be inserted and fixed to the brake bolt. External hex nut fixings require a hole of around 6mm, the hex nut is fixed to the protruding part of the brake bolt.

For a more detailed guide on getting the right brakes check out our journal.

Campagnolo Record Long NOS/NIB Vintage M3 x 45 mm Dropout Adjuster Screws

£30.88 £32.50

✓ Original pair of dropout adjusters - in production from the 1970s to the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Campagnolo Record dropout adjuster set (or alignment adjusting screws if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong dropout adjusters!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Thread Size - this is almost always 3.0 x 0.5 mm, with just one exception found on Huret dropouts where the thread size required is 3.0 x 0.6 mm. These can be tapped to accept standard dropouts if required.

Total Length - from end to end, including the end nut and screw head.

Cinelli Model 1A Milano Logo Vintage 90 mm 1" Quill Stem

£71.25 £75.00

✓ Original part - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Cinelli Model 1A handlebar stem (or gooseneck if you prefer), hailing from Italy and in production during the 1970s. Made from aluminium/steel and weighing in at 275 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are strongly recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - Gruppo S.R.L. Cinelli Department, Via G. di Vittorio 21, Caleppio di Settala (MI), 20090 Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Sakae/Ringyo (SR) c.1984 Vintage 80 mm 1" Quill Stem

£38.00 £40.00

✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Sakae/Ringyo (SR) handlebar stem (or gooseneck if you prefer), hailing from Japan and dating back to 1984. Made from aluminium/steel and weighing in at 349 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are strongly recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

3TTT Record Strada (Mod.1) 2nd Type Paratella Pantographed Vintage 100 mm 1" Quill Stem

£118.75 £125.00

✓ Original part - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

3TTT Record Strada handlebar stem (or gooseneck if you prefer), hailing from Italy and in production during the 1970s. Made from aluminium and weighing in at 263 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are strongly recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - 3T Cycling SRL, Via Leonardo Da Vinci 19, Presezzo (BG), 24030 Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

3TTT Record Strada (Mod.1) 3rd Type Paratella Pantographed Vintage 85 mm 1" Quill Stem

£137.75 £145.00

✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

3TTT Record Strada handlebar stem (or gooseneck if you prefer), hailing from Italy and in production from the 1970s to the 1980s. Made from aluminium/steel and weighing in at 250 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are strongly recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - 3T Cycling SRL, Via Leonardo Da Vinci 19, Presezzo (BG), 24030 Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

3TTT Record 84 (AR84) 1st Type Vintage 100 mm 1" Quill Stem

£66.50 £70.00

✓ Original part - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

3TTT Record 84 handlebar stem (or gooseneck if you prefer), hailing from Italy and in production during the 1980s. Made from aluminium and weighing in at 281 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are strongly recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - 3T Cycling SRL, Via Leonardo Da Vinci 19, Presezzo (BG), 24030 Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Campagnolo Nuovo/Super/C-Record / Euclid (748) Silver NOS Vintage Crank Arm Bolts Set

£26.13 £27.50

✓ Original parts - in production from the 1970s to the 1990s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Campagnolo Nuovo/Super/C-Record / Euclid crankset fixing bolts (or bottom bracket screws if you prefer), hailing from Italy and in production from the 1970s to the 1990s (yet still new & unused after all this time). Made from steel and weighing in at 34 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank bolts!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Crank Bolt Type - 15 mm hex bolts used to be standard but some older TA, Stronglight and Zeus cranks used a larger 16 mm bolt, plus a few Japanese makers used a smaller 14 mm hex head. Allen key types were introduced in the 1980s and some are self-extracting, which means the crank removes itself when you undo the bolts.

Crank Bolt Thread - All square taper bottom brackets have a standard M8 x 1 mm thread, the only different thread types you’ll find on crank bolts are the much larger M12 & M15 bolts that are specifically for Octalink and ISIS bottom brackets.

Plastiche Cassano NOS Vintage White Expanding Handlebar End Plugs

£16.63 £17.50

✓ Original bar plugs - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Plastiche Cassano bar end plugs (or caps, or stoppers if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from plastic and weighing in at 22 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bar plugs!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR).

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Plug Type - expanding plug inserts can be adjusted within the given range to fit different handlebar inner diameters. 'Push-in' plugs cannot do this, however they are usually designed to flex a little to give you some wiggle room.

Plug Insert Diameter - this needs to be a close match to the inside diameter of your handlebars, although the plug diameters can be increased a little using tape (cloth handlebar tape is perfect for this). The ranges given for expanding plugs are rounded to the nearest 0.5 mm.

End Stop Diameter - the width of the end cap that butts up to the ends of your handlebars.

Strong NOS Vintage 25.8 mm Seatpost

£20.25 £22.50

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Strong seatpost (or seat pin if you prefer), hailing from Japan and in production during the 1980s (yet still new & unused after all this time). Made from aluminium and weighing in at 286 grams - pretty lightweight for seatposts at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom, if not you’ll need to measure with a caliper or seatpost sizing tool as the sizes go up in 0.2 mm increments.

Length (Centre of Rails to Base) - measured from where the centre of the saddle rails will sit once installed, all the way to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.

Campagnolo Super Record (4062) 3rd Gen Vintage Brake Levers

£166.25 £175.00

✓ Original levers - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & cleaned
✓ Worldwide shipping

Campagnolo Super Record drop bar brake levers (or handles if you prefer), hailing from Italy and in production during the 1980s. Made from aluminium/rubber and weighing in at 232 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong brake levers!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are strongly recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - CAMPAGNOLO Srl, Via della Chimica 4, 36100, Vicenza, Italy

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Cable Routing - non-aero means the cables come out at the top of the brake levers, meaning the cables are on show. With aero levers the cable comes out of a small hole by the handlebar, allowing the cables to be hidden under the handlebar tape.

Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. This will rarely present a problem with drop bars as 23.8 mm is standard, and a 24.2 mm clamp will fit just fine as they do have a little adjustment in them. There are some older sizes to watch out for but these will be noticeably different.

Simplex SJ (SJ 6013) Early Version Vintage Braze-On Right Downtube Shifter

£38.00 £40.00

✓ Original shifter - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Simplex SJ right downtube shifter, hailing from France and in production during the 1970s. Made from steel/aluminium and weighing in at 31 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifter!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Fixing Type - if you have small mounts on either side of the frame’s down tube you need braze-on shifters, if there are no mounts you’ll need clamp-on (sometimes referred to as band-on). Some 'aero' frames have mounts fixed to the top of the down tube, for these frames you require top mount shifters for the correct boss type (see below).

Shift Type - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting. For this to work correctly you must use the same system as your rear derailleur, if you're using friction levers you can mix and match. You don't need to worry about the front derailleur as left downtube shifters aren't indexed.

Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction shifters you can in theory run any shifters with any speed setup, although the right lever will need to be pulled back further to shift into the larger cogs.

Shifter Boss Type - the shape of the mount (for braze-on fixings only). Campagnolo / ISO is standard and easily identified by the flat sections on either side, usually combined with a square base for the backing stop plates to fit. There are also Shimano ones with a keyhole shaped base and much less common French ones that are round with no flat sections.

Boss Thread Size - M5 (5 mm) is standard for Campagnolo / ISO bosses, but Shimano bosses will often have M4.5 (4.5 mm) threads and the French bosses would likely have 5 x 1 mm threads.

Blackburn Vintage Black / Red Bottle Cages

£33.25 £35.00

✓ Original pair of bottle cages - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Blackburn water bottle cages (or bidon holders if you prefer), hailing from the United States and in production during the 1980s. Made from aluminium/plastic and weighing in at 78 grams (the weight and price displayed are for a pair of cages). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or a similar vintage event, these are of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong bottle carriers!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR).

Product Manufacturer - Blackburn Design, 1001 Innovation Road Rantoul, IL 61866 USA

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Cage Fixing - most bottle cages will be designed to fix to the frame, although some rare older ones mount to the handlebars and/or stem. If your frame doesn't have any bottle cage braze-ons to fix to you'll need clamp-on bottle cages.

Bottle Fit - almost all cycling bottles measure between 70 - 75 mm in diameter so this is the standard bottle cage size, the only rather rare exceptions are some old Elite bottles that require a 66 mm cage, the more recent oversized ones and of course the funny shaped aero ones that only accept the bottle they were made for.

Regina Extra CX-S (50) Unidirectional Vintage 6/7/8 Speed Chain

£61.75 £65.00

✓ Original part - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked, cleaned & re-lubricated
✓ Worldwide shipping

Regina Extra CX-S chain, hailing from Italy and in production during the 1980s. Made from steel and weighing in at 300 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chain!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are strongly recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Optimal Speed - the ideal number of rear cogs, based on the outer width of the chain and the cog width it was designed for. For 6 Speed Shimano Uniglide a 5/6 spd chain will perform best.

Shifting System(s) - indexed shifters 'click' when you change gear. For 9 speed upwards (or Suntour Accushift), to guarantee the best performance we recommend using the dedicated chain. Otherwise, for 8 speed and below, or any speed when using friction shifting (non-index), you just need the correct outer width.

Outer width - measured across the rivets at the widest point, these are the approximate widths for different speed setups (up to 4 speed is also dependent on cog width):

Speed	Outer Width
2 to 4 Speed (1/8”)	8.5 to 9.5 mm
Up to 6 Speed (3/32”)	7.8 to 8.0 mm
7 Speed / ‘Narrow’ 6 Speed	7.3 mm
8 Speed / ‘Narrow’ 7 Speed	7.0 to 7.3 mm
9 Speed	6.5 to 6.7 mm

Cog Width - the gap between the inner plates allows for different rear cog/sprocket widths. 3/32" is the standard for 5 to 8 speed, above that it’s 11/128”. For 4 speed or less, 3/32” and 1/8” were both used, for the latter you will need a 1/8” chain. A wider 3/16" moped chain can be used as a heavy duty opton for single cog setups if required).

Chain pitch - the distance between the rivets/pins. All chains will be 1/2" with two exceptions; 3/16" (“inch pitch”) for very early track bikes, or Shimano's short lived 10 mm pitch system from the 70s/80s.

Number of links - if you're unsure how many you need, measure your old chain (each link has two rivets) or one with a similar setup to yours.

Vintage Early TA Style NOS Steel Black Bottle Cage

£15.75 £17.50