£19.00 £20.00
REG toe strap buttons (or ends, or caps, or retainers if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from plastic and weighing in at 4 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe strap buttons!
OVERVIEW
TECHNICAL INFO
£19.00 £20.00
Shimano Crane jockey wheels (or derailleur pulleys if you prefer), hailing from Japan and in production during the 1970s (yet still new & unused after all this time). Made from steel and weighing in at 39 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the jockey wheels!
OVERVIEW
TECHNICAL INFO
Teeth - the tooth count has increased with the introduction of more gears, but this happened very gradually so 10 tooth jockey wheels were standard for a very long time.
*Compatible Speed - the number of cogs the jockey wheels were designed to be used with. When using derailleurs for indexed shifting it's important to stick to this, but friction shifting is much more forgiving so you're unlikely to have any problems using the next speed up or down, providing all the measurements are correct.
Diameter (OD) - the diameter of the jockey wheels, from the outside edge of the teeth. It’s important to stay close to the ones you're replacing to ensure they fit.
Thickness - measured at the widest point, by the centre hole. The spacing has generally become narrower over the years to accommodate more gears.
Centre Hole (ID) - the inside diameter (usually inside the bushing/spacer if present). This rarely presents a problem, but some older jockey wheels have a different diameter so it's worth double checking.
£17.58 £18.50
REG 320 BB barrel sleeve protector (or cover, or seal, or shield, or boot!), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time). A fine choice for keeping your vintage bike's bottom bracket free from dust and water, but great for all bikes with cup & cone BBs as the sleeves are all a standard size.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong BB sleeve!
OVERVIEW
£18.00 £20.00
HL Corp (Zoom) handlebar stem (or gooseneck if you prefer), hailing from China and in production during the 2000s. Made from steel and weighing in at 484 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.
Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".
Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.
Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.
Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
£19.00 £20.00
Kalloy KL100 handlebar stem (or gooseneck if you prefer), hailing from Taiwan and in production from the 1990s to the 2000s. Made from aluminium/steel and weighing in at 349 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
The stem's been carefully cleaned, thoroughly checked and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.
Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".
Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.
Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.
Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
£16.63 £17.50
Plastiche Cassano bar end plugs (or caps, or stoppers if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from plastic and weighing in at 22 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bar plugs!
OVERVIEW
TECHNICAL INFO
Plug Type - expanding plug inserts can be adjusted within the given range to fit different handlebar inner diameters. 'Push-in' plugs cannot do this, however they are usually designed to flex a little to give you some wiggle room.
Plug Insert Diameter - this needs to be a close match to the inside diameter of your handlebars, although the plug diameters can be increased a little using tape (cloth handlebar tape is perfect for this). The ranges given for expanding plugs are rounded to the nearest 0.5 mm.
End Stop Diameter - the width of the end cap that butts up to the ends of your handlebars.
£22.50 £25.00
Kalloy ahead handlebar stem, hailing from Taiwan and in production during the 2000s. Made from aluminium and weighing in at 228 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.
Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.
Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).
Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.
£20.25 £22.50
Strong seatpost (or seat pin if you prefer), hailing from Japan and in production during the 1980s (yet still new & unused after all this time). Made from aluminium and weighing in at 286 grams - pretty lightweight for seatposts at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!
Please note: Once inserted into a frame this cannot be returned, so please make sure to double check the diameter is correct before installing.OVERVIEW
TECHNICAL INFO
Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom, if not you’ll need to measure with a caliper or seatpost sizing tool as the sizes go up in 0.2 mm increments.
Length (Centre of Rails to Base) - measured from where the centre of the saddle rails will sit once installed, all the way to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.
£22.50 £25.00
Unbranded classic seatpost (or seat pin if you prefer), most likely in production during the 2000s. Made from aluminium and weighing in at 288 grams - pretty lightweight for seatposts at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
Please note: Once inserted into a frame this cannot be returned, so please make sure to double check the diameter is correct before installing.OVERVIEW
TECHNICAL INFO
Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom, if not you’ll need to measure with a caliper or seatpost sizing tool as the sizes go up in 0.2 mm increments.
Length (Centre of Rails to Base) - measured from where the centre of the saddle rails will sit once installed, all the way to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.
£20.25 £22.50
Sprint water bottle cages (or bidon holders if you prefer), hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time). Made from aluminium and weighing in at 116 grams (the weight and price displayed are for a pair of cages). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
Cage Fixing - most bottle cages will be designed to fix to the frame, although some rare older ones mount to the handlebars and/or stem. If your frame doesn't have any bottle cage braze-ons to fix to you'll need clamp-on bottle cages.
Bottle Fit - almost all cycling bottles measure between 70 - 75 mm in diameter so this is the standard bottle cage size, the only rather rare exceptions are some old Elite bottles that require a 66 mm cage, the more recent oversized ones and of course the funny shaped aero ones that only accept the bottle they were made for.
£20.25 £22.50
Sprint water bottle cages (or bidon holders if you prefer), hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time). Made from aluminium and weighing in at 114 grams (the weight and price displayed are for a pair of cages). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
Cage Fixing - most bottle cages will be designed to fix to the frame, although some rare older ones mount to the handlebars and/or stem. If your frame doesn't have any bottle cage braze-ons to fix to you'll need clamp-on bottle cages.
Bottle Fit - almost all cycling bottles measure between 70 - 75 mm in diameter so this is the standard bottle cage size, the only rather rare exceptions are some old Elite bottles that require a 66 mm cage, the more recent oversized ones and of course the funny shaped aero ones that only accept the bottle they were made for.
£22.50 £25.00
Tacx Uni water bottle cages (or bidon holders if you prefer), hailing from The Netherlands and in production during the 1990s (yet still new & unused after all this time). Made from aluminium/plastic and weighing in at 108 grams (the weight and price displayed are for a pair of cages). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
Cage Fixing - most bottle cages will be designed to fix to the frame, although some rare older ones mount to the handlebars and/or stem. If your frame doesn't have any bottle cage braze-ons to fix to you'll need clamp-on bottle cages.
Bottle Fit - almost all cycling bottles measure between 70 - 75 mm in diameter so this is the standard bottle cage size, the only rather rare exceptions are some old Elite bottles that require a 66 mm cage, the more recent oversized ones and of course the funny shaped aero ones that only accept the bottle they were made for.
£15.75 £17.50
Vintage water bottle cage (or bidon holder if you prefer), most likely in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from steel/plastic and weighing in at 60 grams (the weight and price displayed are for one cage, if we have more in stock you'll be able to add them to your basket). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong bottle carrier!
OVERVIEW
TECHNICAL INFO
Cage Fixing - most bottle cages will be designed to fix to the frame, although some rare older ones mount to the handlebars and/or stem. If your frame doesn't have any bottle cage braze-ons to fix to you'll need a clamp-on bottle cage.
Bottle Fit - almost all cycling bottles measure between 70 - 75 mm in diameter so this is the standard bottle cage size, the only rather rare exceptions are some old Elite bottles that require a 66 mm cage, the more recent oversized ones and of course the funny shaped aero ones that only accept the bottle they were made for.
£23.75 £25.00
Shimano 105 SC bottom bracket axle (or BB spindle if you prefer), hailing from Japan and in production during the 1990s (yet still new & unused after all this time). Made from steel and weighing in at 172 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Axle Type - for square tapers, the ISO introduced a standard for European makers in the early 90s, JIS then did the same in Asia. Before then it was not so simple, and although there is a degree of interchangeability, the best way to make sure you have the right axle is to stick to the same brand from the same era, ideally the proprietary model.
Axle Length (D) - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing an axle that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.
Centre (B) - measured from the outside of the 'shoulders' of the bearing races, as seen in the diagram.
Drive Side (C) - the right side (with any logos etc on the axle facing you), your right crank and chainrings will mount to this side.
Non-Drive Side (A) - the left side, where the left crank arm will be mounted.
Shell Width - the width of the bottom bracket shell the axle was designed to fit, measured at its widest point.

£23.75 £25.00
Shimano Mountain LX / Exage bottom bracket axle (or BB spindle if you prefer), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time). Made from steel and weighing in at 212 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
Exage Mountain & Exage Trail also used these axles, so they are compatible with those too.
OVERVIEW
TECHNICAL INFO
Axle Type - for square tapers, the ISO introduced a standard for European makers in the early 90s, JIS then did the same in Asia. Before then it was not so simple, and although there is a degree of interchangeability, the best way to make sure you have the right axle is to stick to the same brand from the same era, ideally the proprietary model.
Axle Length (D) - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing an axle that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.
Centre (B) - measured from the outside of the 'shoulders' of the bearing races, as seen in the diagram.
Drive Side (C) - the right side (with any logos etc on the axle facing you), your right crank and chainrings will mount to this side.
Non-Drive Side (A) - the left side, where the left crank arm will be mounted.
Shell Width - the width of the bottom bracket shell the axle was designed to fit, measured at its widest point.

£23.75 £25.00
Sakae/Ringyo (SR) Super Apex left and right bottom bracket cup set, hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 87 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
These are compatible with Apex as well as Super Apex chainsets / bottom bracket axles.
OVERVIEW
TECHNICAL INFO
Bottom Bracket Type - ‘square taper’, as the name suggests have square shaped axle ends that slot into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system.
Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing cups, they often have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.
£19.00 £20.00
Shimano 105 SC left and right bottom bracket cup set, hailing from Japan and in production during the 1990s (yet still new & unused after all this time). Made from steel and weighing in at 102 grams (for the pair). A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Bottom Bracket Type - ‘square taper’, as the name suggests have square shaped axle ends that slot into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system.
Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing cups, they often have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.
£14.25 £15.00
Sakae/Ringyo (SR) Super Apex bottom bracket lockring (or locking ring if you prefer), hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 16 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong lockring
OVERVIEW
TECHNICAL INFO
Bottom Bracket Thread Type - this must match the thread of your bottom bracket for the lockring to fit.
Thread Direction - most bottom brackets only have an adjustable cup on the non-driveside of the bike, so lockrings mostly thread to the right (clockwise), regardless of the thread type. However, some bottom brackets have adjustable cups on both sides so the thread direction may be different.
Thickness - this is rounded to the nearest 0.5 mm.
£23.75 £25.00
Campagnolo C-Record / Chorus / Euclid bottom bracket lockring (or locking ring if you prefer), hailing from Italy and in production from the 1980s to the 1990s (yet still new & unused after all this time). Made from steel and weighing in at 13 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
These were also supplied with many other Campagnolo bottom brackets from the late 1980s to the 1990s, including Croce D'Aune, Athena, Centaur, Olympus & Xenon to name just a few.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong lockring
OVERVIEW
TECHNICAL INFO
Bottom Bracket Thread Type - this must match the thread of your bottom bracket for the lockring to fit.
Thread Direction - most bottom brackets only have an adjustable cup on the non-driveside of the bike, so lockrings mostly thread to the right (clockwise), regardless of the thread type. However, some bottom brackets have adjustable cups on both sides so the thread direction may be different.
Thickness - this is rounded to the nearest 0.5 mm.
£19.00 £20.00
Shimano Dura-Ace / 600 bottom bracket lockring (or locking ring if you prefer), hailing from Japan and in production during the 1970s (yet still new & unused after all this time). Made from steel and weighing in at 14 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong lockring
OVERVIEW
TECHNICAL INFO
Bottom Bracket Thread Type - this must match the thread of your bottom bracket for the lockring to fit.
Thread Direction - most bottom brackets only have an adjustable cup on the non-driveside of the bike, so lockrings mostly thread to the right (clockwise), regardless of the thread type. However, some bottom brackets have adjustable cups on both sides so the thread direction may be different.
Thickness - this is rounded to the nearest 0.5 mm.
£19.00 £20.00
Sugino Royal bottom bracket lockring (or locking ring if you prefer), hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 12 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong lockring
OVERVIEW
TECHNICAL INFO
Bottom Bracket Thread Type - this must match the thread of your bottom bracket for the lockring to fit.
Thread Direction - most bottom brackets only have an adjustable cup on the non-driveside of the bike, so lockrings mostly thread to the right (clockwise), regardless of the thread type. However, some bottom brackets have adjustable cups on both sides so the thread direction may be different.
Thickness - this is rounded to the nearest 0.5 mm.
£14.25 £15.00
Shimano Deore XT bottom bracket lockring (or locking ring if you prefer), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time). Made from steel and weighing in at 13 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Bottom Bracket Thread Type - this must match the thread of your bottom bracket for the lockring to fit.
Thread Direction - most bottom brackets only have an adjustable cup on the non-driveside of the bike, so lockrings mostly thread to the right (clockwise), regardless of the thread type. However, some bottom brackets have adjustable cups on both sides so the thread direction may be different.
Thickness - this is rounded to the nearest 0.5 mm.
£11.88 £12.50
Shimano Deore LX / Exage Mountain bottom bracket lockring (or locking ring if you prefer), hailing from Japan and in production during the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 13 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Bottom Bracket Thread Type - this must match the thread of your bottom bracket for the lockring to fit.
Thread Direction - most bottom brackets only have an adjustable cup on the non-driveside of the bike, so lockrings mostly thread to the right (clockwise), regardless of the thread type. However, some bottom brackets have adjustable cups on both sides so the thread direction may be different.
Thickness - this is rounded to the nearest 0.5 mm.
£14.25 £15.00
Shimano 105 SC / Deore LX caged bottom bracket bearing set (or ball races if you prefer), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bearings!
OVERVIEW
TECHNICAL INFO
Bearing Size - most bottom brackets use 1/4" bearings, but there are some that use smaller sizes so it's advisable to measure your old ones or check with a local bike shop to be sure.
Retainer Type - you can use any type of retaining cage in any bottom bracket as long as the bearing sizes are correct.
£11.88 £12.50
Sakae/Ringyo (SR) Royal / Super Apex caged bottom bracket bearing set (or ball races if you prefer), hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bearings!
OVERVIEW
TECHNICAL INFO
Bearing Size - most bottom brackets use 1/4" bearings, but there are some that use smaller sizes so it's advisable to measure your old ones or check with a local bike shop to be sure.
Retainer Type - you can use any type of retaining cage in any bottom bracket as long as the bearing sizes are correct.
£14.25 £15.00
Shimano Dura-Ace caged bottom bracket bearing set (or ball races if you prefer), hailing from Japan and in production during the 1970s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bearings!
OVERVIEW
TECHNICAL INFO
Bearing Size - most bottom brackets use 1/4" bearings, but there are some that use smaller sizes so it's advisable to measure your old ones or check with a local bike shop to be sure.
Retainer Type - you can use any type of retaining cage in any bottom bracket as long as the bearing sizes are correct.
£14.25 £15.00
Zefal TX Switch bicycle pump, hailing from France and in production during the 1990s (yet still new & unused after all this time). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.
£23.75 £25.00
CST Super HP tyres, hailing from China and in production during the 1980s. Made from rubber and weighing in at 690 grams (the weight and price displayed are for a pair of tyres). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong tyres!
The tyres have been thoroughly checked and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Size - this is the manufacturer’s sizing and must match the size or your wheels. This can be confusing as tyres have had different sizing systems over the years, and there are many (sometimes conflicting) sizes available. For this reason it’s important to check the ISO diameter too for clarification, especially for 26” wheels.
Bike Type - the type of bike the tyres were designed to be used on. Road tyres will generally be narrow with minimal tread, touring tyres wider with a bit more grip in the tread, and cyclocross & MTB tyres wider still (especially the latter), with a much more pronounced tread pattern.
ISO Diameter - this relates to the diameter of the wheel rims at the point where the tyres are seated (bead seat diameter). This is a universal measurement, often displayed on tyres as 28-622 or similar, 28 referring to the tyre width and 622 being the ISO diameter in millimetres.
TPI - stands for threads per inch and refers to the thread count of the tyre casings. A high thread count usually means more supple and lighter tyres, this can be anything as high as 320 tpi. We can’t always provide this information however, as it’s not always possible to know for sure.
£23.75 £25.00
Schwalbe Black Jack tyres, hailing from Germany. Made from rubber and weighing in at 1360 grams (the weight and price displayed are for a pair of tyres). A fine choice for keeping your modern bike correct, but also great for any other compatible bike.
The tyres have been thoroughly checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Size - this is the manufacturer’s sizing and must match the size or your wheels. This can be confusing as tyres have had different sizing systems over the years, and there are many (sometimes conflicting) sizes available. For this reason it’s important to check the ISO diameter too for clarification, especially for 26” wheels.
Bike Type - the type of bike the tyres were designed to be used on. Road tyres will generally be narrow with minimal tread, touring tyres wider with a bit more grip in the tread, and cyclocross & MTB tyres wider still (especially the latter), with a much more pronounced tread pattern.
ISO Diameter - this relates to the diameter of the wheel rims at the point where the tyres are seated (bead seat diameter). This is a universal measurement, often displayed on tyres as 28-622 or similar, 28 referring to the tyre width and 622 being the ISO diameter in millimetres.
TPI - stands for threads per inch and refers to the thread count of the tyre casings. A high thread count usually means more supple and lighter tyres, this can be anything as high as 320 tpi. We can’t always provide this information however, as it’s not always possible to know for sure.
SUBSCRIBE TO GET THE FIRST SCOOP
Exclusive content, new products, subscriber only promotions. Delivered to your inbox by tiny cyclists, every few weeks.
Don't worry, you can unsubscribe at any time.
PEDAL PEDLAR
T: 02036758003 // E: info@pedalpedlar.co.uk
© 2026 Pedal Pedlar.
Ecommerce Software by Shopify