Pre-1987 (Eroica Compliant)

Strong w) Clamp NOS Vintage 27.0 mm Bullet Nose / Candlestick Seatpost

£33.75 £37.50

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Strong seatpost, hailing from Japan and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 217 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom, if not you’ll need to measure with a caliper or seatpost sizing tool as the sizes go up in 0.2 mm increments.

Length (Top to Bottom) - measured from the top to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.

Stronglight 99 NOS Vintage 51T 86 BCD Outer Chainring

£45.00 £50.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Stronglight 99 chainring, hailing from France and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from aluminium and weighing in at 147 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainring!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Tooth Count - the number of teeth on the chainring, the higher the number the harder the gear.

Between Adjacent Bolt Holes - the measurement from the centre of any bolt hole to the centre of an adjacent one, if this measurement is the same as that of your crankset and the bolt count is the same then the chainring should fit.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is the technical way to determine whether the chainring fits your crankset. To calculate, multiply the distance between adjacent holes (in mm) by 1.709 (you’ll likely need to round the resulting number up or down a little).

Bolt Count - the number of bolts securing the chainring to the chainset. As with the BCD, this must be the same as your chainset.

Chain Width - 3/32” is the standard width for double and triple chainsets, wherease 1/8” chainrings are only found on single ring chainsets, generally for track / singlespeed use and can only be used with a wide 1/8" chain.

Intended Speed - the number of cogs at the back the chainring was designed to be used with. We refer to it as ‘intended’ speed as most double and triple chainsets will actually work with different speeds than originally intended, but the further away you get from the intended speed the more likely you are to experience minor setup issues. The exception being some chainrings intended for 10 speed use or higher, with these it’s better to stick to the intended speed.

Stronglight JP1000A NOS/NIB Vintage Threadless 121 mm Bottom Bracket

£130.50 £145.00

✓ Original part - produced in the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Stronglight JP1000A bottom bracket, hailing from France and in production during the 1980s (yet still new & unused after all this time!). Made from steel/aluminium and weighing in at 310 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bottom bracket!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing a bottom bracket the cups should have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.

Axle Length - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing a bottom bracket that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.

Axle Type - you can tell which type of axle you need just by looking at the shape of the bottom bracket hole in your crankset. The square taper axle came in two variations; JIS which was produced for cranksets made in Asia and ISO for cranksets made in Europe, these taper down to a slightly smaller end than JIS axles. There are a few exceptions such as some Sugino cranksets that required an ISO axle and some older Dura-Ace cranksests which used a shorter 'low profile' variation of the JIS taper. Ofmega/Avocet also had their own variaton of the ISO taper which is not compatible with any other type.

Sugino NOS Vintage Crank Arm Bolts Set

£21.38 £22.50

✓ Original parts - in production from the 1980s to the 1990s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Sugino crankset fixing bolts (or bottom bracket screws if you prefer), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from steel and weighing in at 30 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank bolts!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Crank Bolt Type - 15 mm hex bolts used to be standard but some older TA, Stronglight and Zeus cranks used a larger 16 mm bolt, plus a few Japanese makers used a smaller 14 mm hex head. Allen key types were introduced in the 1980s and some are self-extracting, which means the crank removes itself when you undo the bolts.

Crank Bolt Thread - All square taper bottom brackets have a standard M8 x 1 mm thread, the only different thread types you’ll find on crank bolts are the much larger M12 & M15 bolts that are specifically for Octalink and ISIS bottom brackets.

Sugino NOS Vintage Crank Dust Caps / Covers

£36.00 £40.00

✓ Original parts - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Sugino crank dust caps, hailing from Japan and in production during the 1970s (yet still new & unused after all this time!). Made from plastic and weighing in at 3 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong dust covers!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Crank Thread - 22 mm is the standard thread for almost all cotterless cranks, the only exceptions are some Stronglight cranks made up until the early 1980s, and Specialites T.A. Campagnolo produced some self-extracting crank bolts with covers that had a reverse thread.

Sugino Royal NOS Vintage English Thread Bottom Bracket Lockring

£20.00

✓ Original BB lockring - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Sugino Royal bottom bracket lockring (or locking ring if you prefer), hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 12 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong lockring

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Due to the product's age, extra care should be taken during installation and use.

Product Manufacturer - 2880 Kuriyama, Namerikawa City, Toyama Prefecture, 936-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bottom Bracket Thread Type - this must match the thread of your bottom bracket for the lockring to fit.

Thread Direction - most bottom brackets only have an adjustable cup on the non-driveside of the bike, so lockrings mostly thread to the right (clockwise), regardless of the thread type. However, some bottom brackets have adjustable cups on both sides so the thread direction may be different.

Thickness - this is rounded to the nearest 0.5 mm.

Sugino Royal RY-BBS Triple R-68-T NOS Vintage 118.5 mm Bottom Bracket Axle

£35.00

✓ Original part - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Sugino Royal bottom bracket axle (or BB spindle if you prefer), hailing from Japan and in production during the 1970s (yet still new & unused after all this time). Made from steel and weighing in at 149 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong axle!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - 2880 Kuriyama, Namerikawa City, Toyama Prefecture, 936-8577, Japan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

We've provided reference below to illustrate how we take the measurements.

Axle Type - for square tapers, the ISO introduced a standard for European makers in the early 90s, JIS then did the same in Asia. Before then it was not so simple, and although there is a degree of interchangeability, the best way to make sure you have the right axle is to stick to the same brand from the same era, ideally the proprietary model.

Axle Length (D) - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing an axle that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.

Centre (B) - measured from the outside of the 'shoulders' of the bearing races, as seen in the diagram.

Drive Side (C) - the right side (with any logos etc on the axle facing you), your right crank and chainrings will mount to this side.

Non-Drive Side (A) - the left side, where the left crank arm will be mounted.

Shell Width - the width of the bottom bracket shell the axle was designed to fit, measured at its widest point.

Sugino Super Mighty Drilled Black NOS/NIB Vintage 54T 144 BCD Outer Chainring

£58.50 £65.00

✓ Original part - produced in the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Sugino Super Mighty chainring, hailing from Japan and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium and weighing in at 97 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainring!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Tooth Count - the number of teeth on the chainring, the higher the number the harder the gear.

Between Adjacent Bolt Holes - the measurement from the centre of any bolt hole to the centre of an adjacent one, if this measurement is the same as that of your crankset and the bolt count is the same then the chainring should fit.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is the technical way to determine whether the chainring fits your crankset. To calculate, multiply the distance between adjacent holes (in mm) by 1.709 (you’ll likely need to round the resulting number up or down a little).

Bolt Count - the number of bolts securing the chainring to the chainset. As with the BCD, this must be the same as your chainset.

Chain Width - 3/32” is the standard width for double and triple chainsets, wherease 1/8” chainrings are only found on single ring chainsets, generally for track / singlespeed use and can only be used with a wide 1/8" chain.

Intended Speed - the number of cogs at the back the chainring was designed to be used with. We refer to it as ‘intended’ speed as most double and triple chainsets will actually work with different speeds than originally intended, but the further away you get from the intended speed the more likely you are to experience minor setup issues. The exception being some chainrings intended for 10 speed use or higher, with these it’s better to stick to the intended speed.

Suntour (LD-1500) Power Shifter NOS Vintage Clamp-On Downtube Shifters

£61.75 £65.00

✓ Original shifters - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour downtube shifters, hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 117 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifters!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

Suntour 8.8.8 Perfect NOS/NIB Vintage 5 Speed 14-19 Freewheel

£63.75 £75.00

✓ Original part - produced in the 1970s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour 8.8.8 Perfect freewheel, hailing from Japan and in production during the 1970s (yet still new & unused after all this time!). Made from steel and weighing in at 343 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong freewheel!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Speed - the number of cogs on the freewheel.

Range - the number of teeth on the smalles and largest cogs, this gives you an indication of how hard or easy the gearing will be, the lower the number the harder the gears. The tooth count of the cogs inbetween are usually evenly spaced, ie: a 6 speed 14-24 freewheel would likely have cog sizes 14, 16, 18, 20, 22 & 24.

Threading - this needs to match the thread of your rear hub. ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Hubs with a French thread must be used with a French threaded freewheel.

Stack Height - the total height (or width if you're looking at it when installed) of the freewheel, this is measured from the base (back of the largest cog) to the top (front of the smallest cog).

Chain width - this is mainly relevant for singlespeed and some older 3 or 4 speed freewheels - if this is ⅛” then you must use a ⅛” chain, but most freewheels (especially multiple speed ones) will use a standard 3/32” chain.

Suntour Cyclone (BB-400) c.1985 NOS Vintage Italian 115 mm Bottom Bracket

£137.75 £145.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 284 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour Cyclone bottom bracket, hailing from Japan and dating back to 1985 (yet still new & unused after all this time!). Made from steel and weighing in at 284 grams - pretty lightweight for a bottom bracket at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bottom bracket!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing a bottom bracket the cups should have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.

Axle Length - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing a bottom bracket that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.

Axle Type - you can tell which type of axle you need by looking at the shape of the bottom bracket hole in your crankset. For square tapers, the ISO introduced a standard for European makers in the early 90s, JIS then did the same in Asia. Before then it was not so simple, and although there is a degree of interchangeability, the best way to make sure you have the right axle is to stick to the same brand from the same era, ideally the proprietary model.

Suntour Cyclone (LD-1600) NOS Vintage Clamp-On Right Downtube Shifter

£38.00 £40.00

✓ Original shifter - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour Cyclone right downtube shifter, hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 49 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifter!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Fixing Type - if you have small mounts on either side of the frame’s down tube you need braze-on shifters, if there are no mounts you’ll need clamp-on (sometimes referred to as band-on). Some 'aero' frames have mounts fixed to the top of the down tube, for these frames you require top mount shifters for the correct boss type (see below).

Shift Type - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting. For this to work correctly you must use the same system as your rear derailleur, if you're using friction levers you can mix and match. You don't need to worry about the front derailleur as left downtube shifters aren't indexed.

Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction shifters you can in theory run any shifters with any speed setup, although the right lever will need to be pulled back further to shift into the larger cogs.

Shifter Boss Type - the shape of the mount (for braze-on fixings only). Campagnolo / ISO is standard and easily identified by the flat sections on either side, usually combined with a square base for the backing stop plates to fit. There are also Shimano ones with a keyhole shaped base and much less common French ones that are round with no flat sections.

Boss Thread Size - M5 (5 mm) is standard for Campagnolo / ISO bosses, but Shimano bosses will often have M4.5 (4.5 mm) threads and the French bosses would likely have 5 x 1 mm threads.

Suntour Cyclone (LD-1600) NOS/NIB Vintage Clamp-On Right Downtube Shifter

£33.25 £35.00

✓ Original shifter - in production from the 1970s to the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour Cyclone right downtube shifter, hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 82 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifter!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Fixing Type - if you have small mounts on either side of the frame’s down tube you need braze-on shifters, if there are no mounts you’ll need clamp-on (sometimes referred to as band-on). Some 'aero' frames have mounts fixed to the top of the down tube, for these frames you require top mount shifters for the correct boss type (see below).

Shift Type - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting. For this to work correctly you must use the same system as your rear derailleur, if you're using friction levers you can mix and match. You don't need to worry about the front derailleur as left downtube shifters aren't indexed.

Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction shifters you can in theory run any shifters with any speed setup, although the right lever will need to be pulled back further to shift into the larger cogs.

Shifter Boss Type - the shape of the mount (for braze-on fixings only). Campagnolo / ISO is standard and easily identified by the flat sections on either side, usually combined with a square base for the backing stop plates to fit. There are also Shimano ones with a keyhole shaped base and much less common French ones that are round with no flat sections.

Boss Thread Size - M5 (5 mm) is standard for Campagnolo / ISO bosses, but Shimano bosses will often have M4.5 (4.5 mm) threads and the French bosses would likely have 5 x 1 mm threads.

Suntour NOS Vintage Crank Bolts

£36.00 £40.00

✓ Original parts - in production from the 1980s to the 1990s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour crank bolts, hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from steel and weighing in at 31 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank bolts!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Crank Bolt Type - 15 mm hex bolts used to be standard but some older TA, Stronglight and Zeus cranks used a larger 16 mm bolt, plus a few Japanese makers used a smaller 14 mm hex head. Allen key types were introduced in the 1980s and some are self-extracting, which means the crank removes itself when you undo the bolts.

Crank Bolt Thread - All square taper bottom brackets have a standard M8 x 1 mm thread, the only different thread types you’ll find on crank bolts are the much larger M12 & M15 bolts that are specifically for Octalink and ISIS bottom brackets.

Suntour NOS Vintage Road Gear Shifter Cable Inners

£20.00

✓ Original cables - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour set of 2 inner cables (or wires if you prefer), hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cables!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Cable Type - brake and gear cables have different specifications and are not interchangeable.

Length (F/R) - it's important to check the cables are long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.

End Nipple Type - only relevant for brake cables. 'Pear' type cable ends step down in size to allow them to be used with drop bar levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.

End Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.

Suntour Perfect (PN-6000) c.1984 NOS/NIB Vintage 6 Speed 16-21 Freewheel

£109.25 £115.00

✓ Original part - produced in the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour Perfect freewheel, hailing from Japan and dating back to 1984 (yet still new & unused after all this time!). Made from steel and weighing in at 489 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong freewheel!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

Suntour Road VX (LD-1900) NOS Vintage Clamp-On Downtube Shifters

£52.25 £55.00

✓ Original shifters - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour Road VX downtube shifters, hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 81 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifters!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Fixing Type - if you have small mounts on either side of the frame’s down tube you need braze-on shifters, if there are no mounts you’ll need clamp-on (sometimes referred to as band-on). Some 'aero' frames have mounts fixed to the top of the down tube, for these frames you require top mount shifters for the correct boss type (see below). There are also 'Clamp-Over' shifters that allow front & rear shifters to be used on a frame that only has a single braze-on.

Shift Type - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting. For this to work correctly you must use the same system as your rear derailleur, if you're using friction levers you can mix and match. You don't need to worry about the front derailleur as left downtube shifters aren't indexed.

Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction shifters you can in theory run any shifters with any speed setup, although the right lever will need to be pulled back further to shift into the larger cogs.

Shifter Boss Type - the shape of the mount (for braze-on fixings only). Campagnolo / ISO is standard and easily identified by the flat sections on either side, usually combined with a square base for the backing stop plates to fit. There are also Shimano ones with a keyhole shaped base and much less common French ones that are round with no flat sections.

Boss Thread Size - M5 (5 mm) is standard for Campagnolo / ISO bosses, but Shimano bosses will often have M4.5 (4.5 mm) threads and the French bosses would likely have 5 x 1 mm threads.

Suntour WL-100 NOS Vintage Tunnel & Stop Down Tube Gear Cable Guide / Clip

£25.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour WL-100 down tube gear cable guide, hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 24 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable guide!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Number of Cables - the number of cables the guide is designed to accept.

Guide Type - some setups require specific guides for the derailleurs to operate correctly. Tunnels simply act as a channel to guide the cable whereas stops create an end point for the cable housing, giving the cable the leverage it needs. Bar control stops are required when using handlebar shifters if your frame doesn't have any guides or braze-ons.

Tube Diameter - most steel (and early lugged aluminium) frames will have a down tube of 28.0 mm - 28.6 mm, this was standard for a long time but there are 'oversized' steel and aluminium tubes that have a diameter of 31.8, 34.9 and even 38.1 mm.

Suntour XCD NOS Vintage Crank Dust Caps / Covers

£18.00 £20.00

✓ Original parts - in production from the 1980s to the 1990s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Suntour XCD crank dust caps, hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from plastic and weighing in at 2 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong dust covers!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Crank Thread - 22 mm is the standard thread for almost all cotterless cranks, the only exceptions are some Stronglight cranks made up until the early 1980s, and Specialites T.A. Campagnolo produced some self-extracting crank bolts with covers that had a reverse thread.

Super Champion Record NOS Vintage 36h 28"/700c Tubular Rim

£68.00 £85.00

✓ Original part - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 365 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Super Champion Record rim, hailing from France and in production during the 1970s (yet still new & unused after all this time!). Made from aluminium and weighing in at 365 grams - incredibly lightweight for a rim at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong rim!

OVERVIEW

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).

Super Champion Record Silver NOS Vintage 36h 28"/700c Tubular Rims

£137.75 £145.00

✓ Original pair of rims - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 780 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Super Champion Record wheel rims, hailing from France and in production during the 1970s (yet still new & unused after all this time!). Made from aluminium and weighing in at 780 grams (the weight and price displayed are for a pair of rims) - incredibly lightweight for a pair of rims at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong rims!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Drilling - the number of holes for the spokes.

Rim Size - the sizing given by the manufacturer, these can be confusing so we also give the ISO diameter too for clarification.

ISO Diameter - the diameter of the rim at the point where the tyre is seated (bead seat diameter). This is a universal measurement, often displayed on tyres as 28-622 or similar, 28 referring to the tyre width and 622 being the ISO diameter in millimetres.

Valve Type - presta valves are the thin ones and Schrader are the fatter ones. Schrader valve holes will also accept the older Dunlop/Woods type valves.

Rim Width (OD) - the width of the rim, measured from the outside of one wall to the other.

Rim Height - the overall height of the rim, measured to the highest point of the rim’s profile.

Tange Hirame Branded Chrome Plated NOS Vintage 27" 1" Threaded Steel Forks

£110.00

✓ Original vintage forks - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Tange Hirame Branded forks, hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 823 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong forks!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

Tange NA NOS Vintage English Bottom Bracket Cups

£30.00

✓ Original parts - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Tange left and right bottom bracket cup set, hailing from Japan and in production during the 1980s (yet still new & unused after all this time). Made from steel and weighing in at 112 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong BB cups!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - TANGE International Co. Ltd, No.483, Minyi St, Xiushui Township, Changhua County 50444,Taiwan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bottom Bracket Type - ‘square taper’, as the name suggests have square shaped axle ends that slot into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system.

Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing cups, they often have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.

Thun NOS Vintage Single 48T Cottered Town/City Crank/Chainset

£40.50 £45.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Thun crank/chainset, hailing from Germany and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 946 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Chainring Count - the number of chainrings on the chainset. Fixed gear track bikes, single-speeds and some geared bikes use a single chainring, road bikes commonly use a double (two rings) and most touring bikes and mountain bikes will use a triple chainset (three rings).

Tooth count - the number of teeth on the chainring(s), the higher the number the harder the gear.

Chain width - this is only relevant for chainsets with a single chainring - if this is ⅛” then you must use a ⅛” chain. All double and triple (and some single) ring chainsets will use a standard 3/32” chain.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is only really needed when changing chainrings. To calculate the BCD, measure the distance in millimeters from the centre of any chainring bolt to the centre of an adjacent one and multiply it by 1.709 (you’ll likely need to round the resulting number up or down a little to get your BCD measurement).

*Intended speed - the number of cogs at the back the chainset was designed to be used with. We refer to it as ‘intended’ speed as most double and triple chainsets will actually work with different speeds than originally intended, but the further away you get from the intended speed the more likely you are to experience minor setup issues. The exception being some chainsets intended for 10 speed use or higher, with these it’s better to stick to the intended speed.

Crank arm length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.

Pedal threads - the thread type to match that of the chainset, this must match and is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Bottom bracket type - ‘square taper’, as the name suggests have a square shaped axle that slots into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a chainset that matches.

Tiger NOS Vintage 3 Speed 16-22 Freewheel

£45.00

✓ Original part - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Tiger freewheel, hailing from the United Kingdom and in production during the 1970s (yet still new & unused after all this time!). Made from steel and weighing in at 299 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong freewheel!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

Top Ribbon NOS/NIB Vintage Green Vinyl Handlebar Tape

£19.00 £20.00

✓ Original bar tape - in production from the 1970s to the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Top Ribbon bar tape (or grip, or wrap if you prefer), hailing from France and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

Triplex Campagnolo Type NOS Vintage Road Gear Shifter Cable Inners

£15.00

✓ Original cables - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex set of 2 inner cables (or wires if you prefer), hailing from Spain and in production from the 1970s to the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cables!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Cable Type - brake and gear cables have different specifications and are not interchangeable.

Length (F/R) - it's important to check the cables are long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.

End Nipple Type - only relevant for brake cables. 'Pear' type cable ends step down in size to allow them to be used with drop bar levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.

End Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.

Triplex NOS Vintage Braze-On Downtube Shifters

£38.25 £45.00

✓ Original shifters - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 53 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex downtube shifters, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium and weighing in at 53 grams - pretty lightweight for downtube shifters at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifters!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

Triplex NOS Vintage Clamp-On 28.6 mm Front Derailleur

£33.25 £35.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex front derailleur, hailing from Spain and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel/plastic and weighing in at 146 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Triplex NOS Vintage Clamp-On 28.6 mm Front Derailleur

£33.25 £35.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex front derailleur, hailing from Spain and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel/plastic and weighing in at 146 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Triplex NOS Vintage Rear Mech

£52.25 £55.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 199 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex rear mech, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 199 grams - incredibly lightweight for a rear derailleur at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong rear mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).

▼HELP SECTION

---

Shifting system - friction means your gear levers don't click when you change gear, when they do click it's referred to as indexed shifting. If you have indexed gear levers they must use the same system as the rear derailleur, if you're using friction levers you can mix and match.

*Speed - the number of cogs at the back the derailleur was designed to be used with. This is important with indexed shifting, but with friction shifters you can in theory run any rear mech with any number of cogs, but you are more likely to have issues running high numbers of cogs with mechs from earlier eras.

Max cog size - the amount of teeth on the largest cog of your freewheel/cassette can be no greater than this to work with this derailleur.

Chain wrap - subtract the size of your smallest rear cog from your biggest, then do the same with your chainrings, add the 2 numbers together and you have your chain wrap.

Chain width - generally speaking, derailleurs designed for more than 3 speed use will fit a standard 3/32'' chain, the exception being some Cyclo & Simplex models from around the mid 1900s.

Triplex Profesional NOS Vintage Braze-On Front Derailleur

£42.75 £45.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex Profesional front derailleur, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 105 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Triplex Profesional NOS Vintage Clamp-On 28.6 mm Front Mech

£42.75 £45.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex Profesional front mech, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 113 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).

Unbranded Bullet Nose NOS Vintage 23.0 mm Seatpost

£20.00 £25.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 191 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage seatpost, most likely in production during the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 191 grams - incredibly lightweight for seatposts at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).

Unbranded Bullet Nose NOS Vintage 23.4 mm Seatpost

£24.00 £30.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 192 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage seatpost, most likely in production during the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 192 grams - incredibly lightweight for seatposts at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).

Unbranded Bullet Nose NOS Vintage 26.0 mm Seatpost

£21.25 £25.00

✓ Original part - in production from the 1960s to the 1980s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 157 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage Bullet Nose seatpost, most likely in production from the 1960s to the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 157 grams - incredibly lightweight for seatposts at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

Unbranded Bullet Nose NOS Vintage 27.2 mm Seatpost

£19.00 £20.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 129 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage seatpost, most likely in production during the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 129 grams - incredibly lightweight for seatposts at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).

Unbranded Chrome NOS Steel Vintage 490 mm Porteur Handlebars

£47.50 £50.00

✓ Original bars - in production from the 1960s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage handlebars, most likely in production from the 1960s to the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 453 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bars!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Width - the total width at its widest point, from end to end, rounded to the nearest 5 mm.

Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.

Grip Diameter - the outside diameter of the area where handlebar grips are fitted, this determines not only what grips will fit but brake levers too so it's important to check if you have a specific setup in mind.

Rise/Drop - we measure this at the end of the bars, from the centre point of the clamp area to the centre of the end. This measurent can change when the bar is rotated so there is a bit of tolerance here, please use this as an approximate measurement only.

Unbranded Monza NOS Vintage 500 ml m Water Bottle

£9.00 £10.00

✓ Original water bottle - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage Monza water bottle, most likely in production during the 1980s (yet still new & unused after all this time!). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!

If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong water bottle!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Capacity - 500ml used to be the standard sized bottle, but the taller modern versions tend to be 750ml.

Bottle width - almost all bottle cages take a 75 mm bottle width, the only rather rare exceptions are some old Elite cages that take a 66 mm bottle (and of course the funny shaped aero ones).

Unbranded NOS Vintage 170 mm Left Crank Arm

£22.50 £25.00

✓ Original part - in production from the 1960s to the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage left crank arm, most likely in production from the 1960s to the 1970s (yet still new & unused after all this time!). Made from steel and weighing in at 303 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Crank Arm Length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.

Pedal Threads - the pattern of the thread that your pedals screw into, this is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Bottom Bracket Type - ‘square taper’, as the name suggests have a square shaped axle that slots into the crank and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a crank that matches.

Unbranded NOS Vintage 500 ml Water Bottle

£15.00

✓ Original water bottle - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage water bottle, most likely in production from the 1970s to the 1980s (yet still new & unused after all this time!). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!

If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong water bottle!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Capacity - 500ml used to be the standard sized bottle, but the taller modern versions tend to be 750ml.

Bottle width - almost all bottle cages take a 75 mm bottle width, the only rather rare exceptions are some old Elite cages that take a 66 mm bottle (and of course the funny shaped aero ones).

Unbranded NOS Vintage Single 48T Cottered Town/City Crank/Chainset

£40.50 £45.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage crank/chainset, most likely in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 876 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Chainring Count - the number of chainrings on the chainset. Fixed gear track bikes, single-speeds and some geared bikes use a single chainring, road bikes commonly use a double (two rings) and most touring bikes and mountain bikes will use a triple chainset (three rings).

Tooth count - the number of teeth on the chainring(s), the higher the number the harder the gear.

Chain width - this is only relevant for chainsets with a single chainring - if this is ⅛” then you must use a ⅛” chain. All double and triple (and some single) ring chainsets will use a standard 3/32” chain.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is only really needed when changing chainrings. To calculate the BCD, measure the distance in millimeters from the centre of any chainring bolt to the centre of an adjacent one and multiply it by 1.709 (you’ll likely need to round the resulting number up or down a little to get your BCD measurement).

*Intended speed - the number of cogs at the back the chainset was designed to be used with. We refer to it as ‘intended’ speed as most double and triple chainsets will actually work with different speeds than originally intended, but the further away you get from the intended speed the more likely you are to experience minor setup issues. The exception being some chainsets intended for 10 speed use or higher, with these it’s better to stick to the intended speed.

Crank arm length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.

Pedal threads - the thread type to match that of the chainset, this must match and is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Bottom bracket type - ‘square taper’, as the name suggests have a square shaped axle that slots into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a chainset that matches.

Unbranded NOS Vintage Size 58 Black Vinyl Hairnet Helmet

£75.00

✓ Original hairnet - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Vintage hairnet head protector (or Danish helmet if you prefer), most likely in production from the 1970s to the 1980s (yet still new & unused after all this time). An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, a hairnet is the perfect finishing touch. It won't give you the protection of a modern helmet of course, so please take care, but you'll certainly look the part.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR).

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Head Circumference - measured around the inside edge of the head band. The material often has a little flex but this needs to be close to your head circumference for a secure fit. This may differ from any stamp / label on the product, as we measure this ourselves for accuracy consistency.

Unbranded SL 2000 Black NOS Size M Vintage Steel Toe Clips / Cages

£22.50 £25.00

✓ Original toe clips - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage SL 2000 toe clips, most likely in production during the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 79 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!

OVERVIEW

**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.

Toe Strap Type - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.

Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.

Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).

Union White Plastic City NOS Vintage Town/City Pedals

£21.25 £25.00

✓ Original pedals - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 329 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Union White Plastic City pedals, hailing from Germany and in production during the 1970s (yet still new & unused after all this time!). Made from steel/plastic and weighing in at 329 grams - pretty lightweight for pedals at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pedals!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Pedal Type - this is just a guide to give you an idea of the pedal type, but any pedal can technically be used for any purpose. Track pedals are designed without the pointed 'quill' for safety though, so it's best to only use track pedals for this purpose. Most track pedals, along with quill & aero road pedals are designed to be used with toe clips & straps for best performance.

Pedal Threads - this must match the thread on your cranks. Sometimes it's stamped on the end of the crank arm, but most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Universal Model 125 / Model 300 Black Edition NOS/NIB Vintage Brake Set

£213.75 £225.00

✓ Original parts - in production from the 1970s to the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Universal Model 125 brake calipers with Model 300 brake levers, hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 708 grams for the set. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong brake set!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Caliper Type - side pull calipers (single or dual pivot) require nothing more than a brake hole to fix them to as the cable feeds straight into one of the arms, whereas centre pull calipers require a brazed-on or fitted cable hanger to allow the cable to be pulled from the centre.

Brake Drop - measured from the centre of the brake mounting hole to the centre of the wheel rim, measured in a straight line. Your measurement must be within the range of the caliper's given brake drop.

Brake Fixing - this refers to the way the brake is secured to the bike. For recessed allen key fixings the hole to the rear of the the fork crown/brake bridge should measure around 8mm, allowing the allen key head to be inserted and fixed to the brake bolt. External hex nut fixings require a hole of around 6mm, the hex nut is fixed to the protruding part of the brake bolt.

Cable Routing - non-aero means the cables come out at the top of the brake levers, meaning the cables are on show. With aero levers the cable comes out of a small hole by the handlebar, allowing the cables to be hidden under the handlebar tape.

Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. This will rarely present a problem with drop bars as 23.8 mm is standard, and a 24.2 mm clamp will fit just fine as they do have a little adjustment in them. There are some older sizes to watch out for but these will be noticeably different.

Velda Campagnolo Type NOS/NIB Vintage Front Road Brake Cable Inner

£7.50

✓ Original cable - in production from the 1960s to the 1970s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Velda inner cable (or wire if you prefer), hailing from Belgium and in production from the 1960s to the 1970s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Position - rear cables need to be longer than fronts, this is the only difference so cables long enough for the rear can also be used on the front.

Cable Type - brake and gear cables have different specifications and are not interchangeable.

Length - it's important to check the cable is long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.

End Nipple Type - only relevant for brake cables. 'Pear' type cable ends step down in size to allow them to be used with drop bar levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.

End Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.

Velda Mafac Type B NOS/NIB Vintage Front Road Brake Cable Inner

£7.50

✓ Original cable - in production from the 1960s to the 1970s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Velda inner cable (or wire if you prefer), hailing from Belgium and in production from the 1960s to the 1970s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Position - rear cables need to be longer than fronts, this is the only difference so cables long enough for the rear can also be used on the front.

Cable Type - brake and gear cables have different specifications and are not interchangeable.

Length - it's important to check the cable is long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.

End Nipple Type - only relevant for brake cables. 'Pear' type cable ends step down in size to allow them to be used with drop bar levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.

End Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.

Velda Mafac Type B NOS/NIB Vintage Road Brake Cable Inner

£8.50

✓ Original cable - in production from the 1960s to the 1970s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Velda inner cable (or wire if you prefer), hailing from Belgium and in production from the 1960s to the 1970s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Position - rear cables need to be longer than fronts, this is the only difference so cables long enough for the rear can also be used on the front.

Cable Type - brake and gear cables have different specifications and are not interchangeable.

Length - it's important to check the cable is long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.

End Nipple Type - only relevant for brake cables. 'Pear' type cable ends step down in size to allow them to be used with drop bar levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.

End Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.

Velda NOS/NIB Vintage Simplex / Huret Road Gear Shifter Cable Inner

£12.50

✓ Original cable - in production from the 1950s to the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Velda inner cable (or wire if you prefer), hailing from Belgium and in production from the 1950s to the 1970s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Position - rear cables need to be longer than fronts, this is the only difference so cables long enough for the rear can also be used on the front.

Cable Type - brake and gear cables have different specifications and are not interchangeable.

Length - it's important to check the cable is long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.

End Nipple Type - only relevant for brake cables. 'Pear' type cable ends step down in size to allow them to be used with drop bar levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.

End Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.