Pre-1987 (Eroica Compliant)

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

Rim Size - this should match the size your bike frame is designed to fit. Standard/full size tubulars only come in one wheel size, these are often referred to as 28" or 700c (sometimes even 27"). These are all the same size, the next size down is 26", so any rims larger than 26" will be standard/full size tubulars.

Bike Type - this is really just a guide, as technically any wheels can be used on any bike as long as everything's compatible. Within reason of course - we wouldn't recommend riding a set of skinny tubular road wheels down a mountain!

Drilling (F/R) - the number of spokes in each wheel (front/rear).

Spacing (O.L.D.) (F/R) - the width of the hubs measured at their widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. These measurements need to match the inside of your frame and fork’s dropouts. Steel frames can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon frames should never be stretched.

Speed - the number of cogs the rear hub was designed to be used with.

Sprocket Fitting - for cassette hubs this refers to the spline pattern (the shape of the cogs where they slide on to the hub) and this must match the cassette you intend to use. With freewheel hubs it refers to the thread, ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Freewheel hubs with a French thread must be used with a French threaded freewheel.

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom., otherwise you’ll need to measure with a caliper or seatpost sizing tool as seatpost diameters go up in 0.2 mm increments.

Length (Centre of Rails to Base) - measured from where the centre of the saddle rails will sit once installed, all the way to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing a bottom bracket the cups should have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.

Axle Length - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing a bottom bracket that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.

Axle Type - you can tell which type of axle you need just by looking at the shape of the bottom bracket hole in your crankset. The square taper axle came in two variations; JIS which was produced for cranksets made in Asia and ISO for cranksets made in Europe, these taper down to a slightly smaller end than JIS axles. There are a few exceptions such as some Sugino cranksets that required an ISO axle and some older Dura-Ace cranksests which used a shorter 'low profile' variation of the JIS taper. Ofmega/Avocet also had their own variaton of the ISO taper which is not compatible with any other type.