Pre-1987 (Eroica Compliant)

Intended Side - some brake levers have a designated side to go on, although most can be used on either the left or right.

Cable Routing - non-aero means the cables come out at the top of the brake lever, meaning the cables are on show. With aero levers the cable comes out of a small hole by the handlebar, allowing the cables to be hidden under the handlebar tape.

Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. This will rarely present a problem with drop bars as 23.8 mm is standard, and a 24.2 mm clamp will fit just fine as they do have a little adjustment in them. There are some older sizes to watch out for but these will be noticeably different.

Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.

Construction - the number of panels the cap body is made up of, not including the peak.

Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.

Construction - the number of panels the cap body is made up of, not including the peak.

Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.

Construction - the number of panels the cap body is made up of, not including the peak.

Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.

Construction - the number of panels the cap body is made up of, not including the peak.

Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.

Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.

Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!

Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.

Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.

Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.

Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!

Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.

Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.

*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.

Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.

End nut length - the total length of the nut from end to end.