£25 to £50

Tioga BB-501 Sealed NOS/NIB Classic English Bottom Bracket Cups

£47.50 £50.00

✓ Original parts - produced in the 1990s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

Tioga BB-501 left and right bottom bracket cup set, hailing from the United States and in production during the 1990s (yet still new & unused after all this time). Made from steel and weighing in at 149 grams (for the pair). A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Bottom Bracket Type - ‘square taper’, as the name suggests have square shaped axle ends that slot into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system.

Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing cups, they often have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.

Tranz-X JD-002 Centeron G-Pulley Blue NOS/NIB Classic 10T Jockey Wheels

£30.00

✓ Original jockey wheels - produced in the 1990s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

Tranz-X JD-002 jockey wheels (or derailleur pulleys if you prefer), hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time). Made from aluminium and weighing in at 46 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Teeth - the tooth count has increased with the introduction of more gears, but this happened very gradually so 10 tooth jockey wheels were standard for a very long time.

*Compatible Speed - the number of cogs the jockey wheels were designed to be used with. When using derailleurs for indexed shifting it's important to stick to this, but friction shifting is much more forgiving so you're unlikely to have any problems using the next speed up or down, providing all the measurements are correct.

Diameter (OD) - the diameter of the jockey wheels, from the outside edge of the teeth. It’s important to stay close to the ones you're replacing to ensure they fit.

Thickness - measured at the widest point, by the centre hole. The spacing has generally become narrower over the years to accommodate more gears.

Centre Hole (ID) - the inside diameter (usually inside the bushing/spacer if present). This rarely presents a problem, but some older jockey wheels have a different diameter so it's worth double checking.

Tranz-X JD-002 Centeron G-Pulley Red NOS/NIB Classic 10T Jockey Wheels

£30.00

✓ Original jockey wheels - produced in the 1990s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

Tranz-X JD-002 jockey wheels (or derailleur pulleys if you prefer), hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time). Made from aluminium and weighing in at 46 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Teeth - the tooth count has increased with the introduction of more gears, but this happened very gradually so 10 tooth jockey wheels were standard for a very long time.

*Compatible Speed - the number of cogs the jockey wheels were designed to be used with. When using derailleurs for indexed shifting it's important to stick to this, but friction shifting is much more forgiving so you're unlikely to have any problems using the next speed up or down, providing all the measurements are correct.

Diameter (OD) - the diameter of the jockey wheels, from the outside edge of the teeth. It’s important to stay close to the ones you're replacing to ensure they fit.

Thickness - measured at the widest point, by the centre hole. The spacing has generally become narrower over the years to accommodate more gears.

Centre Hole (ID) - the inside diameter (usually inside the bushing/spacer if present). This rarely presents a problem, but some older jockey wheels have a different diameter so it's worth double checking.

Tranz-X JD-002 Centeron G-Pulley Silver NOS/NIB Classic 10T Jockey Wheels

Sold Out £30.00

✓ Original jockey wheels - produced in the 1990s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

Tranz-X JD-002 jockey wheels (or derailleur pulleys if you prefer), hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time). Made from aluminium and weighing in at 46 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Teeth - the tooth count has increased with the introduction of more gears, but this happened very gradually so 10 tooth jockey wheels were standard for a very long time.

*Compatible Speed - the number of cogs the jockey wheels were designed to be used with. When using derailleurs for indexed shifting it's important to stick to this, but friction shifting is much more forgiving so you're unlikely to have any problems using the next speed up or down, providing all the measurements are correct.

Diameter (OD) - the diameter of the jockey wheels, from the outside edge of the teeth. It’s important to stay close to the ones you're replacing to ensure they fit.

Thickness - measured at the widest point, by the centre hole. The spacing has generally become narrower over the years to accommodate more gears.

Centre Hole (ID) - the inside diameter (usually inside the bushing/spacer if present). This rarely presents a problem, but some older jockey wheels have a different diameter so it's worth double checking.

Triplex NOS Vintage Braze-On Downtube Shifters

£33.75 £45.00

✓ Original shifters - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 53 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex downtube shifters, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium and weighing in at 53 grams - pretty lightweight for downtube shifters at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifters!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Triplex NOS Vintage Clamp-On 28.6 mm Front Derailleur

£26.25 £35.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex front derailleur, hailing from Spain and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel/plastic and weighing in at 146 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Triplex NOS Vintage Clamp-On 28.6 mm Front Derailleur

£26.25 £35.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex front derailleur, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from steel/plastic and weighing in at 114 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Triplex NOS Vintage Rear Mech

£41.25 £55.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 199 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex rear mech, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 199 grams - incredibly lightweight for a rear derailleur at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong rear mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Shifting system - friction means your gear levers don't click when you change gear, when they do click it's referred to as indexed shifting. If you have indexed gear levers they must use the same system as the rear derailleur, if you're using friction levers you can mix and match.

*Speed - the number of cogs at the back the derailleur was designed to be used with. This is important with indexed shifting, but with friction shifters you can in theory run any rear mech with any number of cogs, but you are more likely to have issues running high numbers of cogs with mechs from earlier eras.

Max cog size - the amount of teeth on the largest cog of your freewheel/cassette can be no greater than this to work with this derailleur.

Chain wrap - subtract the size of your smallest rear cog from your biggest, then do the same with your chainrings, add the 2 numbers together and you have your chain wrap.

Chain width - generally speaking, derailleurs designed for more than 3 speed use will fit a standard 3/32'' chain, the exception being some Cyclo & Simplex models from around the mid 1900s.

Triplex Profesional NOS Vintage Braze-On Front Derailleur

£33.75 £45.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex Profesional front derailleur, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 105 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.

Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.

Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.

Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.

Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.

Triplex Profesional NOS Vintage Clamp-On 28.6 mm Front Mech

£33.75 £45.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Triplex Profesional front mech, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 113 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Truvativ XR NOS/NIB Classic 580 mm Flat/Straight Handlebars

£27.50

✓ Original bars - produced in the 2000s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

Truvativ XR handlebars, hailing from the United States and in production during the 2000s. Made from aluminium and weighing in at 170 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Width - the total width at its widest point, from end to end, rounded to the nearest cm.

Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.

Grip Diameter - the outside diameter of the area where handlebar grips are fitted, this determines not only what grips will fit but brake levers too so it's important to check if you have a specific setup in mind.

Rise/Drop - we measure this at the end of the bars, from the centre point of the clamp area to the centre of the end. This measurent can change when the bar is rotated so there is a bit of tolerance here, please use this as an approximate measurement only.

Tzu Tune Purple Anodised NOS Classic MTB Pedals

£30.00

✓ Original pedals - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Tzu Tune pedals, in production during the 1990s (yet still new & unused after all this time). Made from aluminium/plastic and weighing in at 335 grams - pretty lightweight for pedals at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Pedal Type - this is just a guide to give you an idea of the pedal type, but any pedal can technically be used for any purpose. Track pedals are designed without the pointed 'quill' for safety though, so it's best to only use track pedals for this purpose. Most track pedals, along with quill & aero road pedals are designed to be used with toe clips & straps for best performance.

Pedal Threads - this must match the thread on your cranks. Sometimes it's stamped on the end of the crank arm, but most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Unbranded 4XL Vintage Woollen Cycling Leggings/Tights

£41.25 £55.00

✓ Original vintage leggings - 1970s/80s style!
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & honestly graded
✓ Great alternative to buying new
✓ Worldwide shipping

Vintage leggings, likely made in the 1970s/1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a responsible alternative to buying brand new cycling kit!

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong leggings!

OVERVIEW

DETAIL & SIZING

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

We've also provided photographs below to illustrate how we take our measurements.

Across Waist Band - this measurement is taken across the waist band at the top of the leggings whilst laid flat, without stretching the elastic. To work out the waist circumference this measurement needs to be doubled.

Across Hips - some waist bands are quite high so we also measure around the hip area. This is taken across the leggings whilst laid flat without stretching the elastic, where we assume the hips to be. This is an approximate measurement provided as a guide only.

Full Length (Outside Leg) - measured from the top of the wasit band to the bottom of the hem, measured along the outside of the leg.

Inside Leg - measured from the centre of the crotch to the bottom of the hem, along the inside of the leg.

Across Quads - some leggings can have particularly tight or loose legs, so we also measure around the quad area to help with this. This is taken across the leggings whilst laid flat without stretching the elastic, where we assume the quads to be. This is an approximate measurement provided as a guide only.

Across Bottom Hem - taken across the bottom of one hem whilst laid flat, without stretching the elastic. To work out the hem circumference this measurement needs to be doubled.

Unbranded Bullet Nose NOS Vintage 23.0 mm Seatpost

£25.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 191 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage seatpost, most likely in production during the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 191 grams - incredibly lightweight for seatposts at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Unbranded Bullet Nose NOS Vintage 23.4 mm Seatpost

Sold Out £30.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 192 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage seatpost, most likely in production during the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 192 grams - incredibly lightweight for seatposts at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Unbranded Chrome Steel Vintage 510 mm Moustache/Randonneur Handlebars

£30.00 £40.00

✓ Original bars - in production from the 1960s to the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Unbranded vintage handlebars, most likely in production from the 1960s to the 1970s. Made from steel and weighing in at 448 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bars!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Width - the total width at its widest point, from end to end, rounded to the nearest 5 mm.

Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.

Grip Diameter - the outside diameter of the area where handlebar grips are fitted, this determines not only what grips will fit but brake levers too so it's important to check if you have a specific setup in mind.

Rise/Drop - we measure this at the end of the bars, from the centre point of the clamp area to the centre of the end. This measurent can change when the bar is rotated so there is a bit of tolerance here, please use this as an approximate measurement only.

Unbranded Internal Cable Routed c.1989 Vintage 150 mm 1" Quill Stem

£33.75 £45.00

✓ Original part - produced in the 1980s
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage stem, most likely dating back to 1989. Made from steel and weighing in at 479 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Unbranded Internal Cable Routed c.1990 Classic 135 mm 1 1/8" Quill Stem

£33.75 £45.00

✓ Original part - produced in the 1990s
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded classic stem, most likely dating back to 1990. Made from steel and weighing in at 419 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Unbranded Internal Cable Routed Classic 135 mm 1 1/8" Quill Stem

£26.25 £35.00

✓ Original part - produced in the 1990s
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded classic stem, most likely in production during the 1990s. Made from steel and weighing in at 424 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Unbranded Jonge Trappers XXS Vintage Cycling Shorts

£48.75 £65.00

✓ Original vintage cycling shorts - 1960s/70s style!
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & honestly graded
✓ Great alternative to buying new
✓ Worldwide shipping

Jonge Trappers cycling shorts, likely made in the 1960s/1970s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a responsible alternative to buying brand new cycling kit!

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shorts!

OVERVIEW

DETAIL & SIZING

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

We've also provided photographs below to illustrate how we take our measurements.

Across Waist (Relaxed) - this measurement is taken across the waist with the shorts laid flat, without stretching the elastic. To work out the waist circumference this measurement needs to be doubled.

Across Waist (Full Stretch) - the same as the previous measurement but with the elastic at full stretch.

Full Length (Outside Leg) - measured from the top to the bottom, along the outside of the leg.

Inside Leg - measured from the centre of the crotch to the bottom of the hem, along the inside of the leg.

Across Hem (Relaxed) - taken across the bottom of one hem whilst laid flat, without stretching the elastic. To work out the hem circumference this measurement needs to be doubled.

Across Hem (Full Stretch) - the same as the relaxed hem measurement but with the elastic at full stretch.

Unbranded Large Vintage Cycling Leggings/Tights

£41.25 £55.00

✓ Original vintage leggings - 1970s/80s style!
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & honestly graded
✓ Great alternative to buying new
✓ Worldwide shipping

Vintage leggings, likely made in the 1970s/1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a responsible alternative to buying brand new cycling kit!

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong leggings!

OVERVIEW

DETAIL & SIZING

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

We've also provided photographs below to illustrate how we take our measurements.

Across Waist Band - this measurement is taken across the waist band at the top of the leggings whilst laid flat, without stretching the elastic. To work out the waist circumference this measurement needs to be doubled.

Across Hips - some waist bands are quite high so we also measure around the hip area. This is taken across the leggings whilst laid flat without stretching the elastic, where we assume the hips to be. This is an approximate measurement provided as a guide only.

Full Length (Outside Leg) - measured from the top of the wasit band to the bottom of the hem, measured along the outside of the leg.

Inside Leg - measured from the centre of the crotch to the bottom of the hem, along the inside of the leg.

Across Quads - some leggings can have particularly tight or loose legs, so we also measure around the quad area to help with this. This is taken across the leggings whilst laid flat without stretching the elastic, where we assume the quads to be. This is an approximate measurement provided as a guide only.

Across Bottom Hem - taken across the bottom of one hem whilst laid flat, without stretching the elastic. To work out the hem circumference this measurement needs to be doubled.

Unbranded Large Vintage Cycling Leggings/Tights

£48.75 £65.00

✓ Original vintage leggings - 1970s/80s style!
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & honestly graded
✓ Great alternative to buying new
✓ Worldwide shipping

Vintage leggings, likely made in the 1970s/1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a responsible alternative to buying brand new cycling kit!

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong leggings!

OVERVIEW

DETAIL & SIZING

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

We've also provided photographs below to illustrate how we take our measurements.

Across Waist Band - this measurement is taken across the waist band at the top of the leggings whilst laid flat, without stretching the elastic. To work out the waist circumference this measurement needs to be doubled.

Across Hips - some waist bands are quite high so we also measure around the hip area. This is taken across the leggings whilst laid flat without stretching the elastic, where we assume the hips to be. This is an approximate measurement provided as a guide only.

Full Length (Outside Leg) - measured from the top of the wasit band to the bottom of the hem, measured along the outside of the leg.

Inside Leg - measured from the centre of the crotch to the bottom of the hem, along the inside of the leg.

Across Quads - some leggings can have particularly tight or loose legs, so we also measure around the quad area to help with this. This is taken across the leggings whilst laid flat without stretching the elastic, where we assume the quads to be. This is an approximate measurement provided as a guide only.

Across Bottom Hem - taken across the bottom of one hem whilst laid flat, without stretching the elastic. To work out the hem circumference this measurement needs to be doubled.

Unbranded NOS Vintage Single 48T Cottered Crank/Chainset

£33.75 £45.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Unbranded vintage crank/chainset, most likely in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 876 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Chainring Count - the number of chainrings on the chainset. Fixed gear track bikes, single-speeds and some geared bikes use a single chainring, road bikes commonly use a double (two rings) and most touring bikes and mountain bikes will use a triple chainset (three rings).

Tooth count - the number of teeth on the chainring(s), the higher the number the harder the gear.

Chain width - this is only relevant for chainsets with a single chainring - if this is ⅛” then you must use a ⅛” chain. All double and triple (and some single) ring chainsets will use a standard 3/32” chain.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is only really needed when changing chainrings. To calculate the BCD, measure the distance in millimeters from the centre of any chainring bolt to the centre of an adjacent one and multiply it by 1.709 (you’ll likely need to round the resulting number up or down a little to get your BCD measurement).

*Intended speed - the number of cogs at the back the chainset was designed to be used with. We refer to it as ‘intended’ speed as most double and triple chainsets will actually work with different speeds than originally intended, but the further away you get from the intended speed the more likely you are to experience minor setup issues. The exception being some chainsets intended for 10 speed use or higher, with these it’s better to stick to the intended speed.

Crank arm length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.

Pedal threads - the thread type to match that of the chainset, this must match and is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Bottom bracket type - ‘square taper’, as the name suggests have a square shaped axle that slots into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a chainset that matches.

Unbranded Steel Vintage 1" Threaded Headset

£26.25 £35.00

✓ Original part - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally Checked & Cleaned
✓ Worldwide shipping

Unbranded Steel headset, in production during the 1970s. Made from steel and weighing in at 136 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Unbranded Steel Vintage 39 cm Randonneur Drop Handlebars

£33.75 £45.00

✓ Original bars - in production from the 1950s to the 1960s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked, cleaned & tape residue removed
✓ Worldwide shipping

Unbranded vintage drop handlebars, most likely in production from the 1950s to the 1960s. Made from steel and weighing in at 550 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bars!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

Unbranded Vintage 1" Threaded French Headset

£37.50 £50.00

✓ Original part - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage headset, most likely in production during the 1970s. Made from steel and weighing in at 162 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Headset Type - the 1" size relates to the outside diameter of your fork's steerer column which should measure 25.4 mm, if it's 25.0 mm your forks should be French threaded. Although it's generally recommended to match threaded parts exactly, with headsets you can technically mix and match, unless you have French or the obscure old Raleigh threads, in which case you need to stick to that type. If you're replacing an old headset the thread may be stamped on there. Oversized 1 1/8" & 1 1/4" sizes are easily identifiable due to their size and the threads are all standard.

Cup Size (OD) - the outside diameter of the cups, this must match the inside diameter of your frame's headtube closely for a good fit. For 1" headsets this should be around 30.2 mm unless you require a JIS headset which will be 30.0 mm.

Crown Race (ID) - the inside diameter of the crown race where it sits on the fork steerer, this needs to be close to the outside diameter of your fork steerer at the base to ensure a proper fit.

Stack Height - the overall height of the headset. To check the minimum stack height you require, measure the length of your frame’s head tube & subtract this from the length of the fork steerer column. You can always add spacers if you have a little too much steerer tube but you can't fit a headset with a greater stack height than the space you have available.

For further help with 1" threaded headsets head to our journal.

Unbranded Vintage 1" Threaded Headset

£30.00 £40.00

✓ Original part - in production from the 1960s to the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage headset, most likely in production from the 1960s to the 1970s. Made from steel and weighing in at 182 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Headset Type - the 1" size relates to the outside diameter of your fork's steerer column which should measure 25.4 mm, if it's 25.0 mm your forks should be French threaded. Although it's generally recommended to match threaded parts exactly, with headsets you can technically mix and match, unless you have French or the obscure old Raleigh threads, in which case you need to stick to that type. If you're replacing an old headset the thread may be stamped on there. Oversized 1 1/8" & 1 1/4" sizes are easily identifiable due to their size and the threads are all standard.

Cup Size (OD) - the outside diameter of the cups, this must match the inside diameter of your frame's headtube closely for a good fit. For 1" headsets this should be around 30.2 mm unless you require a JIS headset which will be 30.0 mm.

Crown Race (ID) - the inside diameter of the crown race where it sits on the fork steerer, this needs to be close to the outside diameter of your fork steerer at the base to ensure a proper fit.

Stack Height - the overall height of the headset. To check the minimum stack height you require, measure the length of your frame’s head tube & subtract this from the length of the fork steerer column. You can always add spacers if you have a little too much steerer tube but you can't fit a headset with a greater stack height than the space you have available.

For further help with 1" threaded headsets head to our journal.

Unbranded Vintage 1" Threaded JIS Headset

£26.25 £35.00

✓ Original part - in production from the 1950s to the 1960s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage headset, most likely in production from the 1950s to the 1960s. Made from steel and weighing in at 176 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Headset Type - the 1" size relates to the outside diameter of your fork's steerer column which should measure 25.4 mm, if it's 25.0 mm your forks should be French threaded. Although it's generally recommended to match threaded parts exactly, with headsets you can technically mix and match, unless you have French or the obscure old Raleigh threads, in which case you need to stick to that type. If you're replacing an old headset the thread may be stamped on there. Oversized 1 1/8" & 1 1/4" sizes are easily identifiable due to their size and the threads are all standard.

Cup Size (OD) - the outside diameter of the cups, this must match the inside diameter of your frame's headtube closely for a good fit. For 1" headsets this should be around 30.2 mm unless you require a JIS headset which will be 30.0 mm.

Crown Race (ID) - the inside diameter of the crown race where it sits on the fork steerer, this needs to be close to the outside diameter of your fork steerer at the base to ensure a proper fit.

Stack Height - the overall height of the headset. To check the minimum stack height you require, measure the length of your frame’s head tube & subtract this from the length of the fork steerer column. You can always add spacers if you have a little too much steerer tube but you can't fit a headset with a greater stack height than the space you have available.

For further help with 1" threaded headsets head to our journal.

Unbranded Vintage 1" Threaded JIS Headset

£33.75 £45.00

✓ Original part - in production from the 1950s to the 1960s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage headset, most likely in production from the 1950s to the 1960s. Made from steel and weighing in at 145 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Headset Type - the 1" size relates to the outside diameter of your fork's steerer column which should measure 25.4 mm, if it's 25.0 mm your forks should be French threaded. Although it's generally recommended to match threaded parts exactly, with headsets you can technically mix and match, unless you have French or the obscure old Raleigh threads, in which case you need to stick to that type. If you're replacing an old headset the thread may be stamped on there. Oversized 1 1/8" & 1 1/4" sizes are easily identifiable due to their size and the threads are all standard.

Cup Size (OD) - the outside diameter of the cups, this must match the inside diameter of your frame's headtube closely for a good fit. For 1" headsets this should be around 30.2 mm unless you require a JIS headset which will be 30.0 mm.

Crown Race (ID) - the inside diameter of the crown race where it sits on the fork steerer, this needs to be close to the outside diameter of your fork steerer at the base to ensure a proper fit.

Stack Height - the overall height of the headset. To check the minimum stack height you require, measure the length of your frame’s head tube & subtract this from the length of the fork steerer column. You can always add spacers if you have a little too much steerer tube but you can't fit a headset with a greater stack height than the space you have available.

For further help with 1" threaded headsets head to our journal.

Unbranded Vintage 1" Threaded JIS Headset

£30.00 £40.00

✓ Original part - produced in the 1960s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage headset, most likely in production during the 1960s. Made from steel and weighing in at 162 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Headset Type - the 1" size relates to the outside diameter of your fork's steerer column which should measure 25.4 mm, if it's 25.0 mm your forks should be French threaded. Although it's generally recommended to match threaded parts exactly, with headsets you can technically mix and match, unless you have French or the obscure old Raleigh threads, in which case you need to stick to that type. If you're replacing an old headset the thread may be stamped on there. Oversized 1 1/8" & 1 1/4" sizes are easily identifiable due to their size and the threads are all standard.

Cup Size (OD) - the outside diameter of the cups, this must match the inside diameter of your frame's headtube closely for a good fit. For 1" headsets this should be around 30.2 mm unless you require a JIS headset which will be 30.0 mm.

Crown Race (ID) - the inside diameter of the crown race where it sits on the fork steerer, this needs to be close to the outside diameter of your fork steerer at the base to ensure a proper fit.

Stack Height - the overall height of the headset. To check the minimum stack height you require, measure the length of your frame’s head tube & subtract this from the length of the fork steerer column. You can always add spacers if you have a little too much steerer tube but you can't fit a headset with a greater stack height than the space you have available.

For further help with 1" threaded headsets head to our journal.

Unbranded Vintage 125 mm 1" Quill Stem

£33.75 £45.00

✓ Original part - in production from the 1980s to the 1990s
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage stem, most likely in production from the 1980s to the 1990s. Made from steel and weighing in at 329 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Unbranded Vintage 54T 122 BCD Outer Chainring

£38.25 £45.00

✓ Original part - in production from the 1960s to the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage chainring, most likely in production from the 1960s to the 1970s. Made from steel and weighing in at 295 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainring!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Tooth Count - the number of teeth on the chainring, the higher the number the harder the gear.

Between Adjacent Bolt Holes - the measurement from the centre of any bolt hole to the centre of an adjacent one, if this measurement is the same as that of your crankset and the bolt count is the same then the chainring should fit.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is the technical way to determine whether the chainring fits your crankset. To calculate, multiply the distance between adjacent holes (in mm) by 1.709 (you’ll likely need to round the resulting number up or down a little).

Bolt Count - the number of bolts securing the chainring to the chainset. As with the BCD, this must be the same as your chainset.

Chain Width - 3/32” is the standard width for double and triple chainsets, wherease 1/8” chainrings are only found on single ring chainsets, generally for track / singlespeed use and can only be used with a wide 1/8" chain.

Intended Speed - the number of cogs at the back the chainring was designed to be used with. We refer to it as ‘intended’ speed as most double and triple chainsets will actually work with different speeds than originally intended, but the further away you get from the intended speed the more likely you are to experience minor setup issues. The exception being some chainrings intended for 10 speed use or higher, with these it’s better to stick to the intended speed.

Unbranded Vintage Non-Aero Drop Bar Brake Levers

£30.00 £40.00

✓ Original levers - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & cleaned
✓ Worldwide shipping

Unbranded vintage brake levers, most likely in production during the 1970s. Made from aluminium/rubber and weighing in at 207 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong brake levers!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Cable Routing - non-aero means the cables come out at the top of the brake levers, meaning the cables are on show. With aero levers the cable comes out of a small hole by the handlebar, allowing the cables to be hidden under the handlebar tape.

Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. This will rarely present a problem with drop bars as 23.8 mm is standard, and a 24.2 mm clamp will fit just fine as they do have a little adjustment in them. There are some older sizes to watch out for but these will be noticeably different.

Unbranded Vintage Non-Aero Drop Bar Brake Levers

£45.00 £60.00

✓ Original levers - in production from the 1950s to the 1960s
✓ Thoroughly checked & cleaned
✓ Worldwide shipping

Unbranded vintage brake levers, most likely in production from the 1950s to the 1960s. Made from steel and weighing in at 216 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Cable Routing - non-aero means the cables come out at the top of the brake levers, meaning the cables are on show. With aero levers the cable comes out of a small hole by the handlebar, allowing the cables to be hidden under the handlebar tape.

Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. This will rarely present a problem with drop bars as 23.8 mm is standard, and a 24.2 mm clamp will fit just fine as they do have a little adjustment in them. There are some older sizes to watch out for but these will be noticeably different.

Unbranded Vintage Single 46T 170 mm Right Crank Arm / Chainring Set

£26.25 £35.00

✓ Original part - in production from the 1950s to the 1960s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage right crank/chainring set, most likely in production from the 1950s to the 1960s. Made from steel and weighing in at 591 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Chainring Count - the number of chainrings on the crank. Fixed gear track bikes, single-speeds and some geared bikes use a single chainring, road bikes commonly use a double (two rings) and most touring bikes and mountain bikes will use a triple chainset (three rings).

Tooth Count - the number of teeth on the chainring(s), the higher the number the harder the gear.

Crank Arm Length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is only really needed when changing chainrings. To calculate the BCD, measure the distance in millimeters from the centre of any chainring bolt to the centre of an adjacent one and multiply it by 1.709 (you’ll likely need to round the resulting number up or down a little to get your BCD measurement).

Pedal Threads - the pattern of the thread that your pedals screw into, this is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Bottom Bracket Type - ‘square taper’, as the name suggests have a square shaped axle that slots into the crank and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a crank that matches.

Unbranded Vintage Single 46T 170 mm Right Crank Arm / Chainring Set

£30.00 £40.00

✓ Original part - in production from the 1950s to the 1960s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage right crank/chainring set, most likely in production from the 1950s to the 1960s. Made from steel and weighing in at 530 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Chainring Count - the number of chainrings on the crank. Fixed gear track bikes, single-speeds and some geared bikes use a single chainring, road bikes commonly use a double (two rings) and most touring bikes and mountain bikes will use a triple chainset (three rings).

Tooth Count - the number of teeth on the chainring(s), the higher the number the harder the gear.

Crank Arm Length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is only really needed when changing chainrings. To calculate the BCD, measure the distance in millimeters from the centre of any chainring bolt to the centre of an adjacent one and multiply it by 1.709 (you’ll likely need to round the resulting number up or down a little to get your BCD measurement).

Pedal Threads - the pattern of the thread that your pedals screw into, this is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Bottom Bracket Type - ‘square taper’, as the name suggests have a square shaped axle that slots into the crank and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a crank that matches.

Unbranded Vintage Single 48T 165 mm Right Crank Arm / Chainring Set

£30.00 £40.00

✓ Original part - in production from the 1950s to the 1960s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage right crank/chainring set, most likely in production from the 1950s to the 1960s. Made from steel and weighing in at 555 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Chainring Count - the number of chainrings on the crank. Fixed gear track bikes, single-speeds and some geared bikes use a single chainring, road bikes commonly use a double (two rings) and most touring bikes and mountain bikes will use a triple chainset (three rings).

Tooth Count - the number of teeth on the chainring(s), the higher the number the harder the gear.

Crank Arm Length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is only really needed when changing chainrings. To calculate the BCD, measure the distance in millimeters from the centre of any chainring bolt to the centre of an adjacent one and multiply it by 1.709 (you’ll likely need to round the resulting number up or down a little to get your BCD measurement).

Pedal Threads - the pattern of the thread that your pedals screw into, this is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Bottom Bracket Type - ‘square taper’, as the name suggests have a square shaped axle that slots into the crank and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a crank that matches.

Unbranded Vintage Single 48T Cottered Town/City Crank/Chainset

£34.00 £40.00

✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Unbranded vintage crank/chainset, most likely in production from the 1970s to the 1980s. Made from steel and weighing in at 979 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainset!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Chainring Count - the number of chainrings on the chainset. Fixed gear track bikes, single-speeds and some geared bikes use a single chainring, road bikes commonly use a double (two rings) and most touring bikes and mountain bikes will use a triple chainset (three rings).

Tooth count - the number of teeth on the chainring(s), the higher the number the harder the gear.

Chain width - this is only relevant for chainsets with a single chainring - if this is ⅛” then you must use a ⅛” chain. All double and triple (and some single) ring chainsets will use a standard 3/32” chain.

BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is only really needed when changing chainrings. To calculate the BCD, measure the distance in millimeters from the centre of any chainring bolt to the centre of an adjacent one and multiply it by 1.709 (you’ll likely need to round the resulting number up or down a little to get your BCD measurement).

*Intended speed - the number of cogs at the back the chainset was designed to be used with. We refer to it as ‘intended’ speed as most double and triple chainsets will actually work with different speeds than originally intended, but the further away you get from the intended speed the more likely you are to experience minor setup issues. The exception being some chainsets intended for 10 speed use or higher, with these it’s better to stick to the intended speed.

Crank arm length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.

Pedal threads - the thread type to match that of the chainset, this must match and is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Bottom bracket type - ‘square taper’, as the name suggests have a square shaped axle that slots into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a chainset that matches.

Unbranded Vintage Size 49 Black / Red Leather Hairnet Helmet

£38.00 £40.00

✓ Original hairnet - in production from the 1960s to the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & photpgraphed in detail
✓ Worldwide shipping

Vintage hairnet head protector (or Danish helmet if you prefer), most likely in production from the 1960s to the 1970s. An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, a hairnet is the perfect finishing touch. It won't give you the protection of a modern helmet of course, so please take care, but you'll certainly look the part.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR).

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Head Circumference - measured around the inside edge of the head band. The material often has a little flex but this needs to be close to your head circumference for a secure fit. This may differ from any stamp / label on the product, as we measure this ourselves for accuracy consistency.

Unbranded XL Vintage Cycling Leggings/Tights

£41.25 £55.00

✓ Original vintage leggings - 1970s/80s style!
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & honestly graded
✓ Great alternative to buying new
✓ Worldwide shipping

Vintage leggings, likely made in the 1970s/1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a responsible alternative to buying brand new cycling kit!

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong leggings!

OVERVIEW

DETAIL & SIZING

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

We've also provided photographs below to illustrate how we take our measurements.

Across Waist Band - this measurement is taken across the waist band at the top of the leggings whilst laid flat, without stretching the elastic. To work out the waist circumference this measurement needs to be doubled.

Across Hips - some waist bands are quite high so we also measure around the hip area. This is taken across the leggings whilst laid flat without stretching the elastic, where we assume the hips to be. This is an approximate measurement provided as a guide only.

Full Length (Outside Leg) - measured from the top of the wasit band to the bottom of the hem, measured along the outside of the leg.

Inside Leg - measured from the centre of the crotch to the bottom of the hem, along the inside of the leg.

Across Quads - some leggings can have particularly tight or loose legs, so we also measure around the quad area to help with this. This is taken across the leggings whilst laid flat without stretching the elastic, where we assume the quads to be. This is an approximate measurement provided as a guide only.

Across Bottom Hem - taken across the bottom of one hem whilst laid flat, without stretching the elastic. To work out the hem circumference this measurement needs to be doubled.

Union Block Type NOS Classic Town/City Pedals

£25.00

✓ Original pedals - produced in the 2000s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Union pedals, hailing from Germany and in production during the 2000s. Made from plastic/steel and weighing in at 578 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Pedal Type - this is just a guide to give you an idea of the pedal type, but any pedal can technically be used for any purpose. Track pedals are designed without the pointed 'quill' for safety though, so it's best to only use track pedals for this purpose. Most track pedals, along with quill & aero road pedals are designed to be used with toe clips & straps for best performance.

Pedal Threads - this must match the thread on your cranks. Sometimes it's stamped on the end of the crank arm, but most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Union Curved Block Type NOS Classic Town/City Pedals

£25.00

✓ Original pedals - produced in the 2000s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Union pedals, hailing from Germany and in production during the 2000s. Made from plastic/steel and weighing in at 560 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼SAFETY & COMPLIANCE

---

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are recommended. Due to the product's age, extra care should be taken during use.

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

---

Pedal Type - this is just a guide to give you an idea of the pedal type, but any pedal can technically be used for any purpose. Track pedals are designed without the pointed 'quill' for safety though, so it's best to only use track pedals for this purpose. Most track pedals, along with quill & aero road pedals are designed to be used with toe clips & straps for best performance.

Pedal Threads - this must match the thread on your cranks. Sometimes it's stamped on the end of the crank arm, but most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

Universal CX Vintage Brake Calipers

£48.75 £65.00

✓ Original parts - in production from the 1970s to the 1980s
✓ Lightweight for the era - just 331 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Universal CX brake calipers, hailing from Italy and in production from the 1970s to the 1980s. Made from aluminium/steel and weighing in at 331 grams - pretty lightweight for a pair of brake calipers at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong brakes!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Caliper Type - side pull calipers (single or dual pivot) require nothing more than a brake hole to fix them to as the cable feeds straight into one of the arms, whereas centre pull calipers require a brazed-on or fitted cable hanger to allow the cable to be pulled from the centre.

Brake Drop - measured from the centre of the brake mounting hole to the centre of the wheel rim, measured in a straight line. Your measurement must be within the range of the caliper's given brake drop.

Brake Fixing - this refers to the way the brake is secured to the bike. For recessed allen key fixings the hole to the rear of the the fork crown/brake bridge should measure around 8mm, allowing the allen key head to be inserted and fixed to the brake bolt. External hex nut fixings require a hole of around 6mm, the hex nut is fixed to the protruding part of the brake bolt.

For a more detailed guide on getting the right brakes check out our journal.

Universal Mod. 77 Vintage Brake Calipers

£48.75 £65.00

✓ Original parts - in production from the 1970s to the 1980s
✓ Lightweight for the era - just 348 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Universal Mod. 77 brake calipers, hailing from Italy and in production from the 1970s to the 1980s. Made from aluminium/steel and weighing in at 348 grams - pretty lightweight for a pair of brake calipers at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong brakes!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. Orders are carefully packed, sent with tracking & insurance, and normally collected around midday on Tuesdays and Fridays. Larger items may occasionally require an extra day or two to prepare.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU orders under €150 (excluding shipping) - import VAT and the new €3 customs duty are paid as part of your order, so there's nothing further to pay on delivery.

EU orders over €150 (excluding shipping) - import fees are payable to the carrier before delivery, with nothing collected at checkout.

USA orders - import fees are collected at checkout for all orders to the USA, so there won’t be any surprise charges when your order arrives.

Other international orders - local import fees may apply and are not collected by us. Please check your country's import rules before purchasing.

▼HELP SECTION

---

Caliper Type - side pull calipers (single or dual pivot) require nothing more than a brake hole to fix them to as the cable feeds straight into one of the arms, whereas centre pull calipers require a brazed-on or fitted cable hanger to allow the cable to be pulled from the centre.

Brake Drop - measured from the centre of the brake mounting hole to the centre of the wheel rim, measured in a straight line. Your measurement must be within the range of the caliper's given brake drop.

Brake Fixing - this refers to the way the brake is secured to the bike. For recessed allen key fixings the hole to the rear of the the fork crown/brake bridge should measure around 8mm, allowing the allen key head to be inserted and fixed to the brake bolt. External hex nut fixings require a hole of around 6mm, the hex nut is fixed to the protruding part of the brake bolt.

For a more detailed guide on getting the right brakes check out our journal.

Van Der Heijden's Meubelen Vintage Dutch Cotton Cycling Cap

£27.00 £30.00