Sold Out £30.00
GB Ventoux drop handlebars, hailing from Great Britain and in production from the 1960s to the 1970s. Made from aluminium and weighing in at 402 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bars!
The bars have been checked by one of our mechanics, handlebar tape residue removed and graded as OK condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£14.25 £15.00
GEM bar end plugs (or caps, or stoppers if you prefer), hailing from Great Britain and in production during the 1970s. Made from rubber and weighing in at 16 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bar plugs!
The plugs have been checked, cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Plug Type - expanding plug inserts can be adjusted within the given range to fit different handlebar inner diameters. 'Push-in' plugs cannot do this, however they are usually designed to flex a little to give you some wiggle room.
Plug Insert Diameter - this needs to be a close match to the inside diameter of your handlebars, although the plug diameters can be increased a little using tape (cloth handlebar tape is perfect for this). The ranges given for expanding plugs are rounded to the nearest 0.5 mm.
End Stop Diameter - the width of the end cap that butts up to the ends of your handlebars.
£18.75 £25.00
Georges Sorel bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
Georges Sorel bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
GES Flash Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
GES Flash Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
GES Flash Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£15.00 £20.00
GES Fluor Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£82.50 £110.00
GES Huracan Crono saddle, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from synthetic/steel material and weighing in at 373 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!
OVERVIEW
TECHNICAL INFO
£82.50 £110.00
GES Huracan Crono saddle, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from synthetic/steel material and weighing in at 380 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!
OVERVIEW
TECHNICAL INFO
£82.50 £110.00
GES Huracan Crono saddle, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from synthetic/steel material and weighing in at 395 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!
OVERVIEW
TECHNICAL INFO
£45.00 £60.00
GES Huracan saddle, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from synthetic/steel material and weighing in at 275 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!
OVERVIEW
TECHNICAL INFO
£66.50 £70.00
GES Huracan saddle, hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Made from synthetic/steel material and weighing in at 271 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!
OVERVIEW
TECHNICAL INFO
£13.50 £15.00
GES Race Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£15.00 £20.00
GES Race Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£37.50 £50.00
Gian Robert Competition Gold downtube shifters, hailing from Italy and in production from the 1970s to the 1980s. Made from aluminium/steel and weighing in at 70 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifters!
The shifters have been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£63.75 £85.00
Giordana Brooklyn / Campagnolo Team long sleeved cycling jersey, hailing from Italy and likely made in the 1990s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£26.25 £35.00
Giordana short sleeved cycling jersey, hailing from Italy and likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£46.75 £55.00
Gipiemme Azzuro seatpost, hailing from Italy and in production during the 1980s. Made from aluminium/steel and weighing in at 357 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!
The seatpost's been carefully cleaned, thoroughly checked by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom, if not you’ll need to measure with a caliper or seatpost sizing tool as the sizes go up in 0.2 mm increments.
Length (Centre of Rails to Base) - measured from where the centre of the saddle rails will sit once installed, all the way to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.
£18.00 £20.00
Gipiemme Azzurro front wheel skewer (or hub spindle if you prefer), hailing from Italy and in production from the 1970s to the 1980s. Made from steel and weighing in at 84 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!
The skewer's been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£54.00 £60.00
Gipiemme Crono Special seatpost (or seat pin if you prefer), hailing from Italy and in production during the 1980s. Made from aluminium and weighing in at 259 grams - pretty lightweight for seatposts at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!
The seat post has been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom, if not you’ll need to measure with a caliper or seatpost sizing tool as the sizes go up in 0.2 mm increments.
Length (Centre of Rails to Base) - measured from where the centre of the saddle rails will sit once installed, all the way to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.
£17.00 £20.00
Gipiemme Crono Special rear skewer, hailing from Italy and in production during the 1980s. Made from steel and weighing in at 90 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!
The skewer's been cleaned, checked by one of our mechanics and graded as OK condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£82.50 £110.00
Gipiemme Low Flange hubs, in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 598 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong hubs!
OVERVIEW
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
£86.25 £115.00
Gipiemme Special / Mavic MA2 front wheel, the hub hailing from Italy and dating back to 1984. Made from aluminium/steel and weighing in at 946 grams - pretty lightweight for a front wheel at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong wheel!
The wheel's been serviced, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£38.00 £40.00
Gipiemme Sprint bottom bracket (or BB for short), hailing from Italy and in production during the 1980s. Made from steel and weighing in at 325 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bottom bracket!
The bottom bracket's been carefully cleaned, thoroughly checked by one of our mechanics and graded as OK condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Thread Type - this must match the bottom bracket thread on your frame. The 3 common thread types on classic and vintage bikes are English (also known as British or ISO), Italian & French, and are usually (not always!) found on frames built in their respective countries. If you're replacing a bottom bracket the cups should have the thread type stamped on one of them, if not there are a couple of things to look at; bottom bracket shell width (English & French = 68 mm, Italian = 70 mm) & drive side cup thread direction (English = left, Italian & French = right). The only curveball to watch out for here, although pretty uncommon, are Swiss threads (also found on some French frames, Motobecanes being one) which will have the same shell width & thread direction as an English thread frame but the actual thread pitch will be different. If none of the above matches what you have, there are a few lesser known varieties that will require some further research.
Axle Length - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing a bottom bracket that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.
Axle Type - you can tell which type of axle you need by looking at the shape of the bottom bracket hole in your crankset. For square tapers, the ISO introduced a standard for European makers in the early 90s, JIS then did the same in Asia. Before then it was not so simple, and although there is a degree of interchangeability, the best way to make sure you have the right axle is to stick to the same brand from the same era, ideally the proprietary model.
£183.75 £245.00
Gipiemme Sprint wheels built with Ambrosio Metamorphosis Durex Colnago Corse rims, the hubs hailing from Italy and in production during the 1980s. Made from aluminium/steel and weighing in at 1.9 kg - pretty lightweight for a pair of wheels at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong wheels!
The wheels have been serviced, checked by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£19.13 £23.00
Gipiemme Sprint rear skewer, hailing from Italy and in production during the 1980s. Made from steel and weighing in at 89 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!
The skewer's been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£29.75 £35.00
Gipiemme chainring, hailing from Italy and in production from the 1970s to the 1980s. Made from aluminium and weighing in at 98 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainring!
The chainring's been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Tooth Count - the number of teeth on the chainring, the higher the number the harder the gear.
Between Adjacent Bolt Holes - the measurement from the centre of any bolt hole to the centre of an adjacent one, if this measurement is the same as that of your crankset and the bolt count is the same then the chainring should fit.
BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is the technical way to determine whether the chainring fits your crankset. To calculate, multiply the distance between adjacent holes (in mm) by 1.709 (you’ll likely need to round the resulting number up or down a little).
Bolt Count - the number of bolts securing the chainring to the chainset. As with the BCD, this must be the same as your chainset.
Chain Width - 3/32” is the standard width for double and triple chainsets, wherease 1/8” chainrings are only found on single ring chainsets, generally for track / singlespeed use and can only be used with a wide 1/8" chain.
Intended Speed - the number of cogs at the back the chainring was designed to be used with. We refer to it as ‘intended’ speed as most double and triple chainsets will actually work with different speeds than originally intended, but the further away you get from the intended speed the more likely you are to experience minor setup issues. The exception being some chainrings intended for 10 speed use or higher, with these it’s better to stick to the intended speed.
£17.00 £20.00
Gipiemme crank bolts, hailing from Italy and in production from the 1970s to the 1980s. Made from steel and weighing in at 33 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank bolts!
The crank bolts have been cleaned, checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Crank Bolt Type - 15 mm hex bolts used to be standard but some older TA, Stronglight and Zeus cranks used a larger 16 mm bolt, plus a few Japanese makers used a smaller 14 mm hex head. Allen key types were introduced in the 1980s and some are self-extracting, which means the crank removes itself when you undo the bolts.
Crank Bolt Thread - All square taper bottom brackets have a standard M8 x 1 mm thread, the only different thread types you’ll find on crank bolts are the much larger M12 & M15 bolts that are specifically for Octalink and ISIS bottom brackets.
£17.00 £20.00
Gipiemme crank bolts, hailing from Italy and in production from the 1970s to the 1980s. Made from steel and weighing in at 27 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank bolts!
The crank bolts have been cleaned, checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Crank Bolt Type - 15 mm hex bolts used to be standard but some older TA, Stronglight and Zeus cranks used a larger 16 mm bolt, plus a few Japanese makers used a smaller 14 mm hex head. Allen key types were introduced in the 1980s and some are self-extracting, which means the crank removes itself when you undo the bolts.
Crank Bolt Thread - All square taper bottom brackets have a standard M8 x 1 mm thread, the only different thread types you’ll find on crank bolts are the much larger M12 & M15 bolts that are specifically for Octalink and ISIS bottom brackets.
£17.00 £20.00
Gipiemme crank bolts, hailing from Italy and in production from the 1970s to the 1980s. Made from steel and weighing in at 24 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank bolts!
The crank bolts have been cleaned, checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Crank Bolt Type - 15 mm hex bolts used to be standard but some older TA, Stronglight and Zeus cranks used a larger 16 mm bolt, plus a few Japanese makers used a smaller 14 mm hex head. Allen key types were introduced in the 1980s and some are self-extracting, which means the crank removes itself when you undo the bolts.
Crank Bolt Thread - All square taper bottom brackets have a standard M8 x 1 mm thread, the only different thread types you’ll find on crank bolts are the much larger M12 & M15 bolts that are specifically for Octalink and ISIS bottom brackets.
£30.00 £40.00
Gonso 'Ottenbach Radmarathon 1995' short sleeved cycling jersey, likely made in the 1990s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£22.50 £30.00
Gonso short sleeved cycling jersey, likely made in the 1990s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£30.00 £40.00
Gonso short sleeved cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£26.25 £35.00
Gonso short sleeved cycling jersey, likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£26.25 £35.00
Gonso short sleeved cycling jersey, likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£30.00 £40.00
Gonso short sleeved cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£26.25 £35.00
Gonso sleeveless cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£30.00 £40.00
Gonzo short sleeved cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£12.75 £15.00
Gran Premio toe straps, hailing from Italy and in production from the 1970s to the 1980s. The straps are black in colour and made from leather/steel, the perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe straps!
The toe straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£30.00 £40.00
Grey w) white & neon doodles short sleeved cycling jersey, likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£22.50 £25.00
Haden bullet nose (or candlestick if you prefer) seatpost, hailing from Great Britain and in production during the 1970s (yet still new & unused after all this time!). Made from aluminium and weighing in at 73 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost!
Please note: Once inserted into a frame this cannot be returned, so please make sure to double check the diameter is correct before installing.OVERVIEW
TECHNICAL INFO
Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom, if not you’ll need to measure with a caliper or seatpost sizing tool as the sizes go up in 0.2 mm increments.
Length (Top to Bottom) - measured from the top to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.
£21.25 £25.00
Heta Gran Carrera bicycle pump, hailing from Spain and in production during the 1970s (yet still new & unused after all this time!). An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!
OVERVIEW
TECHNICAL INFO
Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.
Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.
Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!
Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.
£18.00 £20.00
Heta Mascot bicycle pump, hailing from Spain and in production during the 1970s. An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!
The pump's been thoroughly checked, tested and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.
Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.
Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!
Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.
£22.50 £25.00
Heta Sport bicycle pump, hailing from Spain and in production from the 1970s to the 1980s. An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!
The pump's been thoroughly checked, tested and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.
Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.
Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!
Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.
£22.50 £30.00
Hot'n'Wild Hardcore short sleeved cycling jersey, likely made in the 1990s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & SIZING
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£166.25 £175.00
Huret Duopar rear derailleur (or mech if you prefer), hailing from France and in production from the 1970s to the 1980s. Made from titanium/aluminium/ steel and weighing in at 256 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong rear mech!
The mech's been carefully cleaned, thoroughly checked by one of our mechanics and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Shifting system - friction means your gear levers don't click when you change gear, when they do click it's referred to as indexed shifting. If you have indexed gear levers they must use the same system as the rear derailleur, if you're using friction levers you can mix and match.
Speed - the number of cogs at the back the derailleur was designed to be used with. This is important with indexed shifting, but with friction shifters you can in theory run any rear mech with any number of cogs, but you are more likely to have issues running high numbers of cogs with mechs from earlier eras.
Max cog size - the amount of teeth on the largest cog of your freewheel/cassette can be no greater than this to work with this derailleur.
Chain wrap - subtract the size of your smallest rear cog from your biggest, then do the same with your chainrings, add the 2 numbers together and you have your chain wrap.
Chain width - generally speaking, derailleurs designed for more than 3 speed use will fit a standard 3/32'' chain, the exception being some Cyclo & Simplex models from around the mid 1900s.
£33.75 £45.00
Huret Rival front mech, hailing from France and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 97 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong front mech!
OVERVIEW
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
£37.50 £50.00
Hutchinson Corsa Senior tubular/sprint tyre, hailing from France and in production during the 1980s (yet still new & unused after all this time!). Made from rubber/latex and weighing in at 315 grams (the weight and price displayed are for one tyre, if we have more in stock you'll be able to add them to your basket). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong tyre!
NB: Tubular tyres with latex tubes lose air over the course of a few days so will need re-inflating regularly. If mounted in the photos this is for illustrative purpose only, any wheels or rims shown are not included.OVERVIEW
TECHNICAL INFO
Tubular Wheel Size - standard/full size tubulars only come in one wheel size, these are often referred to as 28" or 700c (sometimes even 27"). These are all the same size, the next size down is 26", so any wheel larger than 26" will take a standard/full size tubular.
Width - the width of the tyre as stated by the manufacturer (if present), if there are no markings we measure at the widest point when fully inflated. Depending on the manufacturer, the stated width can differ slightly from the actual width when measured, although usually this only minimal.
Bike Type - the type of bike the tyre was designed to be used on. Road tyres will generally be narrow with minimal tread whereas cyclocross tyres will be wider with a more pronounced tread pattern, and MTB tyres even more so.
Casing - the main structure of the tyre that surrounds the inner tube and provides the base for the rubber tread. Most tubulars have cotton casings but other materials are used such as nylon, kevlar or silk. We can’t always provide this information as it’s not always possible to know for sure.
TPI - stands for threads per inch and refers to the thread count of the casing, if known. A high thread count usually means a more supple and lighter tyre, this can be anything as high as 320 tpi.
Valve Core - some valve cores are removable allowing you to add sealant or valve extenders, if the valve cores are fixed this is not possible.
£41.25 £55.00
Ideale 2001 saddle, hailing from France and in production from the 1970s to the 1980s. Made from leather/steel and weighing in at 330 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!
The saddle's been checked over and graded as OK condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
SUBSCRIBE TO GET THE FIRST SCOOP
Exclusive content, new products, subscriber only promotions. Delivered to your inbox by tiny cyclists, every few weeks.
Don't worry, you can unsubscribe at any time.
PEDAL PEDLAR
T: 02036758003 // E: info@pedalpedlar.co.uk
© 2026 Pedal Pedlar.
Ecommerce Software by Shopify