Miche
36h Miche Pro Team Low Flange Rear Road Hub
£40.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION
| Hole Count: | 36h |
| Spacing: | 130mm |
| Bearing Condition: | Excellent |
| Sprocket Type: | Miche only - not compatible with any other cassettes |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
50T Miche 1/8" NOS Vintage Chainring
£45.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
All chainrings are standard 3/32" for road use unless stated.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Tooth Count: | 50 1/8" |
| BCD: | 135 BCD |
| Condition: | Mint/NOS |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
51T Miche NOS Vintage Chainring
£37.50
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
All chainrings are standard 3/32" for road use unless stated.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Tooth Count: | 51 |
| BCD: | 135 BCD |
| Condition: | NOS |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
Miche / Mavic Monthlery Pro Vintage Tubular Front Track Wheel
£85.00
All our wheels come professionally serviced, including tension check, truing & hub servicing where required. Please refer to the detailed photographs & information below for sizing & condition.
NB: Full size tubulars only come in one size. They are often referred to as 28", but some people call them 27" or 700c.
SIZING & CONDITION:
| Hub: | Miche Track (No Track Nuts but can be Included) |
| Rim: | Mavic Monthlery Pro Tubular |
| Wheel Size: | Standard Sprint/Tubs (28"/700c/27") |
| Hole Count: | 36 |
| Spacing: | 100mm |
| Bearing Condition: | Very Good |
| Rim Wear: | Light |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
Miche 502 Classic Clipless Pedals
£15.00
These classic Miche 502 pedals were produced in the 1990s and weigh in at 394 grams for the pair. They're clipless pedals designed to fit cranks with standard (9/16" x 20 tpi) pedal threads.
The pedals have been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as these are vintage parts, even new old stock pedals may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION
Pedal Type - Clipless
Pedal Threading - Standard (9/16" x 20 tpi)
Body Condition - OK
Bearing/Race Condition - OK
Weight - 394 grams
Era - 1990s
Country - Italian
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
Miche Competition / Mavic GP4 Vintage Tubular Rear Wheel
£110.00
All our wheels come professionally serviced, including tension check, truing & hub servicing where required. Please refer to the detailed photographs & information below for sizing & condition.
NB: Full size tubulars only come in one size. They are often referred to as 28", but some people call them 27" or 700c.
SIZING & CONDITION:
| Hub: | Miche Competition |
| Rim: | Mavic GP4 |
| Wheel Size: | Standard Sprint/Tubs (28"/700c/27") |
| Hole Count: | 32h |
| Rear Spacing: | 126mm |
| Bearing Condition: | Very Good |
| Rim Wear: | Light |
| Sprocket Type: | Screw-On (Italian 1.378 x 24 tpi) |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
Miche Competition Speciali 1201 Vintage Quill Road Pedals
£55.00
✓ Original pedals - produced in the 1980s
✓ Lightweight for the era - just 343 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping
Miche Competition Speciali 1201 pedals, hailing from Italy and in production during the 1980s. Made from aluminium/steel and weighing in at 343 grams - pretty lightweight for pedals at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pedals!
The pedals have been carefully cleaned, thoroughly checked by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Bearing/Race Condition - Very Good
Production Era - 1980s
Country - Italian
Material - Aluminium/Steel
Weight - 343 g
Stock Code- U-PD2V
TECHNICAL INFO
Pedal Type - Quill Road
Pedal Threads - Standard (9/16" x 20 TPI)
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).
Miche Leader NOS/NIB Vintage Chainset
£125.00
✓ Original part - produced in the 1980s
✓ New old stock & still in the original packaging!
✓ Lightweight for the era - just 631 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping
Miche Leader chainset, hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 631 grams - pretty lightweight for a chainset at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainset!
OVERVIEW
Chainring Condition - New Old Stock - In Original Packaging*
Production Era - 1980s
Country - Italian
Material - Aluminium/Steel
Weight - 631 g
Stock Code- D-CS21V
NB - Miche Competition box
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Chainring Count - Double
Tooth Count - 52 / 42
Chain Width - 3/32"
BCD - 144 BCD
Intended Speed* - 5 Speed, 6 Speed, 7 Speed
Crank Length - 170 mm
Pedal Threads - French (14 x 1.25mm)
Bottom Bracket Type - Square Taper
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).
-
▼HELP SECTION
-
Chainring count - the number of chainrings on the chainset. Fixed gear track bikes, single-speeds and some geared bikes use a single chainring, road bikes commonly use a double (two rings) and most touring bikes and mountain bikes will use a triple chainset (three rings).
Tooth count - the number of teeth on the chainring(s), the higher the number the harder the gear.
Chain width - this is only relevant for chainsets with a single chainring - if this is ⅛” then you must use a ⅛” chain. All double and triple (and some single) ring chainsets will use a standard 3/32” chain.
BCD - stands for Bolt Circle Diameter (sometimes referred to as PCD - Pitch Circle Diameter) and is only really needed when changing chainrings. To calculate the BCD, measure the distance in millimeters from the centre of any chainring bolt to the centre of an adjacent one and multiply it by 1.709 (you’ll likely need to round the resulting number up or down a little to get your BCD measurement).
*Intended speed - the number of cogs at the back the chainset was designed to be used with. We refer to it as ‘intended’ speed as most double and triple chainsets will actually work with different speeds than originally intended, but the further away you get from the intended speed the more likely you are to experience minor setup issues. The exception being some chainsets intended for 10 speed use or higher, with these it’s better to stick to the intended speed.
Crank length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.
Pedal threads - the pattern of the thread that your pedals screw into, this is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).
Bottom bracket type - ‘square taper’, as the name suggests have a square shaped axle that slots into the chainset and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a chainset that matches.
Miche NOS Classic 42T 116 BCD Inner Chainring
£30.00
✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Miche chainring, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 62 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.
OVERVIEW
Production Era - 1990s
Country - Italian
Material - Aluminium
Weight - 62 g
Stock Code- D-CRI9C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Tooth Count - 42
Between Adjacent Bolt Holes - 68.2 mm
BCD - 116 BCD
Chainset Type - Double
Bolt Count - 5-Bolt
Chain Width - 3/32"
Intended Speed - 5 Speed, 6 Speed, 7 Speed
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).
Miche Primato Pistard High Flange NOS/NIB Classic 36/36h Hubs
£115.00
✓ Original part - in production from the 1990s to the 2000s
✓ New old stock! Still in the original packaging!
✓ Made in Italy
✓ Worldwide shipping
Miche Primato Pistard hubs, in production from the 1990s to the 2000s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 567 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.
OVERVIEW
Bearing / Race Condition - New Old Stock*
Production Era - 1990s & 2000s
Country - Italian
Material - Aluminium/Steel
Weight - 567 grams
Stock Code- D-HU-PT3C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Drilling (F/R) - 36/36 Hole
Sprocket Type - Lockring Thread - Italian (1.32" x 24 TPI)
Spacing OLD (F/R) - 100 mm / 120 mm
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
Miche Superfast Vintage 36h Front Hub
£35.00
✓ Original part - in production from the 1980s to the 1990s
✓ Made in Italy
✓ Worldwide shipping
Miche Superfast front hub, in production from the 1980s to the 1990s. Made from aluminium/steel and weighing in at 227 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
The hub's been carefully cleaned, thoroughly serviced by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Bearing / Race Condition - Good
Production Era - 1980s & 1990s
Country - Italian
Material - Aluminium/Steel
Weight - 227 grams
Stock Code- U-HU-F10V
TECHNICAL INFO
Drilling - 36 Hole
Spacing (O.L.D.) - 100 mm
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
Miche Vintage Front Derailleur
£17.50
Please check that the fixing type is correct for your frame. Most frames will either take a braze-on type (when your frame has a 'tab' to bolt on to) or a band-on 28.6mm type. Some French frames will have 28.0mm tubing diameter. If you are unsure then you should measure the external diameter of your seat tube.
Please refer closely to the detailed photographs & technical information below to avoid any issues.
TECHNICAL INFO & CONDITION
| Fixing Type: |
Braze-on
|
| Crank Type: |
Double
|
| Condition: |
OK
|
| SKU: | FM193 |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
Miche Vintage Quill Road Pedals
£45.00
✓ Original pedals - produced in the 1980s
✓ Lightweight for the era - just 348 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping
Miche pedals, hailing from Italy and in production during the 1980s. Made from aluminium/steel and weighing in at 348 grams - pretty lightweight for pedals at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pedals!
The pedals have been carefully cleaned, thoroughly checked by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Bearing/Race Condition - OK
Production Era - 1980s
Country - Italian
Material - Aluminium/Steel
Weight - 348 g
Stock Code- U-PD3V
TECHNICAL INFO
Pedal Type - Quill Road
Pedal Threads - Standard (9/16" x 20 TPI)
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).
Miche Vintage Quill Road Pedals
£40.00
✓ Original pedals - produced in the 1970s
✓ Lightweight for the era - just 344 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping
Miche pedals, hailing from Italy and in production during the 1970s. Made from aluminium/steel and weighing in at 344 grams - pretty lightweight for pedals at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pedals!
The pedals have been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Bearing/Race Condition - Good
Condition Notes - One replacement dust cap
Production Era - 1970s
Country - Italian
Material - Aluminium/Steel
Weight - 344 g
Stock Code- U-PD24V
TECHNICAL INFO
Pedal Type - Quill Road
Pedal Threads - Standard (9/16" x 20 TPI)
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).