Under £25
25.4mm Callet Bullet Nose Vintage-Style Seatpost
£20.00
Please check the diameter matches that of your frame, and refer to the table below for other sizings & condition: We measure all seatposts from the centre of the saddle rails to the bottom. 'Bullet-nose' style seatposts are measured from the top to bottom.
Please allow 6cm at the base of the seatpost to be safely inserted into the frame.
SIZING & CONDITION:
| Diameter: | 25.4mm |
| Length (Centre of Rails to Bottom): | 132mm |
| Condition: | Good (Bit Squashed But Fine Above Limit) |
25.4mm Steel Bullet Nose Seatpost
£12.00
-
Classic steel seatpost in the traditional 'bullet nose' style, as found on vintage bikes from the 1940s, 50s, 60s etc. In very good condition, with a few marks as seen in the photos.
-
Diameter: 25.4mm Total Length: 160mm -
UK: £4.50 Europe: £8.50 Rest of World: £13.25
25.4mm Steel Bullet Nose Style Seatpost
£10.00
-
Classic steel seatpost in the traditional 'bullet nose' style, as found on vintage bikes from the 1940s, 50s, 60s etc. In good condition, with some marks as seen in the photos , but still very presenteable.
-
Diameter: 25.4mm Total Length: 180mm -
UK: £4.50 Europe: £8.50 Rest of World: £13.25
26.4mm SR Custom Vintage Seatpost
£15.00
Please check the diameter matches that of your frame, and refer to the table below for other sizings & condition: We measure all seatposts from the centre of the saddle rails to the bottom. 'Bullet-nose' style seatposts are measured from the top to bottom.
Please allow 6cm at the base of the seatpost to be safely inserted into the frame.
SIZING & CONDITION:
| Diameter: | 26.4mm |
| Length (Centre of Rails to Bottom): | 186mm |
| Condition: | Ok (See photographs) |
26T Specialized Classic Chainring
£20.00
This classic Specialized chainring was produced in the 1990s/2000s and weighs in at 23 grams. It's made to fit 74 BCD 5-arm cranks with adjacent bolt holes measuring 43.5 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 5-Arm
Between Adjacent Holes (mm) - 43.5 mm
BCD - 74 BCD
Tooth Count - 26
Width - 3/32" (For Derailleur Gears)
Condition - Very Good
Weight - 23 grams
Era - 1990s, 2000s
Country - North American
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
26t Unbranded Vintage Chainring
£15.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION:
| Bolt Circle Diameter: | 136 BCD |
| Tooth Count: | 26 Tooth |
| Width: |
3/32"
|
| Condition: |
Good
|
| SKU: | CR120 |
36h Normandy Luxe Competition High Flange Road Hub
£20.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION:
| Hole Count: | 36 |
| Axle Width: | 98mm |
| Condition: | OK |
3ttt Celo-Nastro NOS Black / Red / Yellow Handlebar Tape
£15.00
Enough tape for one set of bars, and includes the original end plugs.
View full product details
3ttt NOS Bike Ribbon in Flourescent Green
£20.00
New Old Stock 3ttt Bike Ribbon, still in the original packaging. Very limited stock.
Enough tape for one set of bars, and includes the original end plugs.
View full product details
40t Unbranded Chainring
£20.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION:
| Bolt Circle Diameter: | 118 BCD |
| Tooth Count: | 40 Tooth |
| Width: |
3/32"
|
| Condition: |
Good
|
| SKU: | CR116 |
40T Williams C1000 Vintage c.1953 Chainring
£20.00
This vintage Williams C1000 chainring was produced in the 1950s and weighs in at 205 grams. It's made to fit 88.9 BCD 3-arm cranks with adjacent bolt holes measuring 77.0 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 3-Arm
Between Adjacent Holes (mm) - 77.0 mm
BCD - 88.9 BCD
Tooth Count - 40
Width - 1/8" (Fixed Gear / Singlespeed)
Condition - Good
Weight - 205 grams
Era - 1950s
Country - British
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
42cm Massi Branded Vintage Handlebar
£20.00
All of our bars are measured centre to centre, unless stated my manufacturer on bar. It is essential that you choose the correct centre diameter to match your stem clamp size.
TECHNICAL INFO & CONDITION:
| Width: | 42cm |
| Centre Diameter: | 26.0mm |
| Cable Groove: | Double |
| Condition: | OK |
42T Shimano Biopace Vintage Chainring
£17.50
This vintage Shimano Biopace chainring was produced in the 1980s/1990s and weighs in at 44 grams. It's made to fit 130 BCD 5-arm cranks with adjacent bolt holes measuring 76.4 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 5-Arm
Between Adjacent Holes (mm) - 76.4 mm
BCD - 130 BCD
Tooth Count - 42
Width - 3/32" (For Derailleur Gears)
Condition - Good
Weight - 44 grams
Era - 1980s, 1990s
Country - Japanese
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
42T Specialites TA Vintage Chainring
£20.00
This vintage Specialites TA chainring was produced in the 1970s/1980s and weighs in at 49 grams. It's made to fit 130 BCD 5-arm cranks with adjacent bolt holes measuring 76.4 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 5-Arm
Between Adjacent Holes (mm) - 76.4 mm
BCD - 130 BCD
Tooth Count - 42
Width - 3/32" (For Derailleur Gears)
Condition - Very Good
Weight - 49 grams
Era - 1970s, 1980s
Country - French
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
42T Stronglight Classic Chainring
£20.00
This classic Stronglight chainring was produced in the 1990s and weighs in at 50 grams. It's made to fit 130 BCD 5-arm cranks with adjacent bolt holes measuring 76.4 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 5-Arm
Between Adjacent Holes (mm) - 76.4 mm
BCD - 130 BCD
Tooth Count - 42
Width - 3/32" (For Derailleur Gears)
Condition - Good
Weight - 50 grams
Era - 1990s
Country - French
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
42T Sunrace R80 Fluid Drive Chainring
£15.00
This Sunrace R80 Fluid Drive chainring was produced in the Modern and weighs in at 148 grams. It's made to fit 130 BCD 5-arm cranks with adjacent bolt holes measuring 76.4 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 5-Arm
Between Adjacent Holes (mm) - 76.4 mm
BCD - 130 BCD
Tooth Count - 42
Width - 3/32" (For Derailleur Gears)
Condition - New
Weight - 148 grams
Era - Modern
Country - Taiwanese
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
42t TA Vintage Chainring
£20.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION:
| Bolt Circle Diameter: | 170 BCD |
| Tooth Count: | 42 Tooth |
| Width: |
3/32"
|
| Condition: |
Good
|
| SKU: | CR134_VTG |
42t Unbranded Drilled Vintage Chainring
£17.50
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION:
| Bolt Circle Diameter: | 94 BCD |
| Tooth Count: | 42 Tooth |
| Width: |
3/32"
|
| Condition: |
Very Good
|
| SKU: | CR67 |
42t Unbranded Drilled Vintage Chainring
£15.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION:
| Bolt Circle Diameter: | 144 BCD |
| Tooth Count: | 42 Tooth |
| Width: |
3/32"
|
| Condition: |
OK
|
| SKU: | CR125_VTG |
47t Unbranded Vintage Chainring
£20.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION:
| Bolt Circle Diameter: | 130 BCD |
| Tooth Count: | 47 Tooth |
| Width: |
3/32"
|
| Condition: |
OK
|
| SKU: | CR119 |
50T Unbranded Vintage Chainring
£10.00
This vintage Unbranded chainring was produced in the 1960s/1970s and weighs in at 235 grams. It's made to fit 116 BCD 3-arm cranks with adjacent bolt holes measuring 100.0 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 3-Arm
Between Adjacent Holes (mm) - 100.0 mm
BCD - 116 BCD
Tooth Count - 50
Width - 3/32" (For Derailleur Gears)
Condition - Poor
Weight - 235 grams
Era - 1960s, 1970s
Country - Unknown
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
51T Specialites TA Vintage Chainring
£22.50
This vintage Specialites TA chainring was produced in the 1970s/1980s and weighs in at 79 grams. It's made to fit 144 BCD 5-arm cranks with adjacent bolt holes measuring 84.6 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 5-Arm
Between Adjacent Holes (mm) - 84.6 mm
BCD - 144 BCD
Tooth Count - 51
Width - 3/32" (For Derailleur Gears)
Condition - Good
Weight - 79 grams
Era - 1970s, 1980s
Country - French
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
52T Shimano Biopace Vintage Chainring
£20.00
This vintage Shimano Biopace chainring was produced in the 1980s/1990s and weighs in at 79 grams. It's made to fit 130 BCD 5-arm cranks with adjacent bolt holes measuring 76.4 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 5-Arm
Between Adjacent Holes (mm) - 76.4 mm
BCD - 130 BCD
Tooth Count - 52
Width - 3/32" (For Derailleur Gears)
Condition - Good
Weight - 79 grams
Era - 1980s, 1990s
Country - Japanese
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
52T Sunrace R80 Fluid Drive Chainring
£20.00
This Sunrace R80 Fluid Drive chainring was produced in the Modern and weighs in at 260 grams. It's made to fit 130 BCD 5-arm cranks with adjacent bolt holes measuring 76.4 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 5-Arm
Between Adjacent Holes (mm) - 76.4 mm
BCD - 130 BCD
Tooth Count - 52
Width - 3/32" (For Derailleur Gears)
Condition - New
Weight - 260 grams
Era - Modern
Country - Taiwanese
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
52T Unbranded Vintage Chainring
£20.00
This vintage Unbranded chainring was produced in the 1970s/1980s and weighs in at 80 grams. It's made to fit 144 BCD 5-arm cranks with adjacent bolt holes measuring 84.6 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 5-Arm
Between Adjacent Holes (mm) - 84.6 mm
BCD - 144 BCD
Tooth Count - 52
Width - 3/32" (For Derailleur Gears)
Condition - Good
Weight - 80 grams
Era - 1970s, 1980s
Country - Unknown
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
52T Unbranded Vintage Chainring
£22.50
This vintage Unbranded chainring was produced in the 1960s/1970s and weighs in at 289 grams. It's made to fit 116 BCD 3-arm cranks with adjacent bolt holes measuring 100.0 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 3-Arm
Between Adjacent Holes (mm) - 100.0 mm
BCD - 116 BCD
Tooth Count - 52
Width - 3/32" (For Derailleur Gears)
Condition - Very Good
Weight - 289 grams
Era - 1960s, 1970s
Country - Unknown
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
53T Unbranded Vintage Chainring
£20.00
This vintage Unbranded chainring was produced in the 1970s/1980s and weighs in at 102 grams. It's made to fit 128 BCD 5-arm cranks with adjacent bolt holes measuring 75.2 mm from centre to centre.
The chainring has been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as this is a vintage part, even new old stock chainrings may show signs of age from storage over the years (you can enlarge or zoom into the photos).
TECHNICAL INFO & CONDITION:
Bolt Fit - 5-Arm
Between Adjacent Holes (mm) - 75.2 mm
BCD - 128 BCD
Tooth Count - 53
Width - 3/32" (For Derailleur Gears)
Condition - Good
Weight - 102 grams
Era - 1970s, 1980s
Country - Unknown
If buying from outside of the EU, please remember that there may be import duties to pay upon receipt. View full product details
ACOR Classic 1" Threaded JIS Headset
£20.00
✓ Original part - produced in the 1990s
✓ Made in Taiwan
✓ Professionally Checked & Cleaned
✓ Worldwide shipping
ACOR headset, in production during the 1990s. Made from aluminium and weighing in at 109 grams - pretty lightweight for a headset of this time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.
The headset's been carefully cleaned, thoroughly checked by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Bearing / Race Condition - Very Good
Condition Notes - Needle roller bearings lower, standard bearings upper
Production Era - 1990s
Country - Taiwanese
Material - Aluminium
Weight - 109 grams
Stock Code- U-HS7C
TECHNICAL INFO
Headset Type - 1" Threaded JIS (24 TPI)
Cup Size (OD) - 30.1 mm
Crown Race (ID) - 27.0 mm
Stack Height - 38.5 mm
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the EU please remember that there may be import duties to pay upon receipt.
AFA 1 Vintage Clamp-On Pump Clip
£10.00
| Clamp Size: | 28.6mm |
| Condition: | Very Good |
AFA 1 Vintage Clamp-On Pump Clip
£5.00
| Clamp Size: | 28.6mm |
| Condition: | Very Good (Missing Bolt) |
AFA 1 Vintage Clamp-On Pump Clip
£10.00
| Clamp Size: | 28.6mm |
| Condition: | Very Good |
AFA 1 Vintage Clamp-On Pump Clip
£10.00
| Clamp Size: | 28.6mm |
| Condition: | Very Good |
AFA 1 Vintage Clamp-On Pump Clip
£5.00
| Clamp Size: | 28.6mm |
| Condition: | Very Good (Bolt Missing) |
Afa 2 NOS Plastic Bike Pump
£20.00
| Condition: | NOS-New Old Stock (Shop Related Storage Marks) |
| Material: | Plastic |
| Fit: | Peg |
| Type: | Presta |
| Compressed Length: | 45.5cm |
| Uncompressed Length: | 47.5cm |
AFA 2 Vintage Clamp-on Pump Clip
£5.00