Vintage & NOS
25.4mm Callet Bullet Nose Vintage-Style Seatpost
£20.00
Please check the diameter matches that of your frame, and refer to the table below for other sizings & condition: We measure all seatposts from the centre of the saddle rails to the bottom. 'Bullet-nose' style seatposts are measured from the top to bottom.
Please allow 6cm at the base of the seatpost to be safely inserted into the frame.
SIZING & CONDITION
| Diameter: | 25.4mm |
| Length (Centre of Rails to Bottom): | 132mm |
| Condition: | Good (Bit Squashed But Fine Above Limit) |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
25.4mm Steel Bullet Nose Seatpost
£12.00
-
Classic steel seatpost in the traditional 'bullet nose' style, as found on vintage bikes from the 1940s, 50s, 60s etc. In very good condition, with a few marks as seen in the photos.
-
Diameter: 25.4mm Total Length: 160mm -
UK: £4.50 Europe: £8.50 Rest of World: £13.25
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
25.4mm Steel Bullet Nose Style Seatpost
£10.00
-
Classic steel seatpost in the traditional 'bullet nose' style, as found on vintage bikes from the 1940s, 50s, 60s etc. In good condition, with some marks as seen in the photos , but still very presenteable.
-
Diameter: 25.4mm Total Length: 180mm -
UK: £4.50 Europe: £8.50 Rest of World: £13.25
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
26.4mm SR Laprade NOS Vintage Seatpost
£35.00
Please check the diameter matches that of your frame, and refer to the table below for other sizings & condition: We measure all seatposts from the centre of the saddle rails to the bottom. 'Bullet-nose' style seatposts are measured from the top to bottom.
Please allow 6cm at the base of the seatpost to be safely inserted into the frame.
SIZING & CONDITION
| Diameter: | 26.4mm |
| Length (Centre of Rails to Base): | 195mm |
| Condition: | NOS (Shop Marks, Not Inserted) |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
26.6mm Campagnolo Super Record Fluted Vintage Seatpost
£110.00
Please check the diameter matches that of your frame, and refer to the table below for other sizings & condition: We measure all seatposts from the centre of the saddle rails to the bottom. 'Bullet-nose' style seatposts are measured from the top to bottom.
Please allow 6cm at the base of the seatpost to be safely inserted into the frame.
SIZING & CONDITION
| Diameter: | 26.6mm |
| Length (Centre of Rails to Base): | 210mm |
| Condition: |
Very Good
|
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
26.8mm / 27.0mm NOS Strong Bullet Nose Style Seatpost
£25.00
Please check the diameter matches that of your frame, and refer to the table below for other sizings & condition: We measure all seatposts from the centre of the saddle rails to the bottom. 'Bullet-nose' style seatposts are measured from the top to bottom.
Please allow 6cm at the base of the seatpost to be safely inserted into the frame.
SIZING & CONDITION
| Diameter: |
26.8 / 27.0mm
|
| Length (Centre of Rails to Base): |
200mm
|
| Condition: | NOS (May Have Storage Marks, Not Inserted) |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
26t Unbranded Vintage Chainring
£15.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Bolt Circle Diameter: | 136 BCD |
| Tooth Count: | 26 Tooth |
| Width: |
3/32"
|
| Condition: |
Good
|
| SKU: | CR120 |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
32 or 36h Shimano RX100 HB-A550 NOS Hub Pair
£70.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION
| Hole Count (F/R): | 6/7 Speed in 32/32 Only | 8/9/10 Speed in 32/32 or 36/36 |
| Axle Width (F/R): | 100/126mm for 6/7 Speed | 100/130mm for 8/9/10 Speed |
| Condition: | New Old Stock |
| Sprocket Fitting: | HyperGlide / Uniglide (8 Speed) |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
32h Campagnolo Nuovo/Super Record Low Flange Vintage Rear Road Hub
£55.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION
| Hole Count: | 32h |
| Spacing: | 120mm |
| Bearing Condition: | Excellent |
| Sprocket Type: | Screw-On (Italian 1.378 x 24 tpi) |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
32h Campagnolo S-U Hub Body
£35.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION
| Hole Count: | 32 |
| Condition: | NOS |
| Sprocket Fitting: | Screw-On Freewheel |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
32h Shimano Dura Ace EX Vintage Rear Road Hub
£60.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION
| Hole Count: | 32h |
| Spacing: | 126mm |
| Bearing Condition: | Very Good |
| Sprocket Type: | Shimano Uniglide 6 Speed Dura Ace |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
32t Shimano SG-X Vintage Chainring
£20.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION:
| Bolt Circle Diameter: | 104 BCD |
| Tooth Count: | 32 Tooth |
| Width: |
3/32"
|
| Condition: |
New
|
| SKU: | CR122 |
36h Miche Pro Team Low Flange Rear Road Hub
£40.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION
| Hole Count: | 36h |
| Spacing: | 130mm |
| Bearing Condition: | Excellent |
| Sprocket Type: | Miche only - not compatible with any other cassettes |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
36h Normandy Luxe Competition High Flange Road Hub
£20.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION
| Hole Count: | 36 |
| Axle Width: | 98mm |
| Condition: | OK |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
36h Pelissier 3003 NOS Low Flange Rear Road Hub
£45.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION
| Hole Count: | 36h |
| Spacing: | 130mm |
| Bearing Condition: | New Old Stock |
| Sprocket Type: | Screw On (English/ISO: 1.375 x 24 TPI) |
SHIPPING, TAXES & RETURNS
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, normally within 2-3 days, but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
36h Sachs Maillard 7V NOS Vintage Rear Road Hub
£45.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION
| Hole Count: | 36h |
| Spacing: | 130mm |
| Bearing Condition: | NOS |
| Sprocket Type: | Screw On (English/ISO: 1.375 x 24 TPI) |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
36h Shimano 105 HB-1055 NOS Hubs Pair
£85.00
Our hubs are graded depending on the quality of the cones & bearings, if you can feel any pitting we grade them accordingly. A good service will always improve the condition. Please make sure to check the spacing matches that of your frame.
SIZING & CONDITION
| Hole Count (F/R): | 32/32 or 36/36 |
| Axle Width (F/R): | 100/130mm |
| Condition: | NOS |
| Sprocket Fitting: | HyperGlide & Uniglide Compatible (8 Speed) |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
42t Unbranded Drilled Vintage Chainring
£17.50
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Bolt Circle Diameter: | 94 BCD |
| Tooth Count: | 42 Tooth |
| Width: |
3/32"
|
| Condition: |
Very Good
|
| SKU: | CR67 |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
48-52cm NOS Unpainted Vintage Ladies Frame
£295.00
We found a little batch of these tasty new old stock ladies frames, unpainted but part-chromed. We're not sure who built them, but the workmanship is excellent.
We also offer a full custom build service, so if you need a any of our frames building up into your perfect bike, just give us a shout.
We also carry a wide range of headsets & bottom brackets, and provide a fitting service if you require this.
NB: Fork design may differ slightly from the photo as they were supplied with different forks, but they're all chrome with ISO thread.
| SIZING & SPEC: | |
| Seat Tube (ctt): | 48 cm, 50cm & 52cm |
| Weight: | TBC |
| Tubing: | Steel |
| Rear Spacing: | 130 mm |
| Seatpost Diameter: | 27.2 mm |
| Brake Fixings: | Recessed |
| Dropouts: | Unbranded |
| Bottom Bracket Thread: | British |
| Headset Thread: | British ISO |
| Era: | 1990s |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
50T Miche 1/8" NOS Vintage Chainring
£45.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
All chainrings are standard 3/32" for road use unless stated.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Tooth Count: | 50 1/8" |
| BCD: | 135 BCD |
| Condition: | Mint/NOS |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
50T Stronglight Vintage Chainring
£32.50
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
All chainrings are standard 3/32" for road use unless stated.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Tooth Count: | 50 |
| BCD: | 144 BCD |
| Condition: | Very Good |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
52T 1/8" Unknown Hand-made Vintage Chainring
£45.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
All chainrings are standard 3/32" for road use unless stated.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Tooth Count: | 52 1/8" |
| BCD: | 151 BCD |
| Condition: | Good |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
52t/50t Unbranded Vintage Chainring
£25.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Bolt Circle Diameter: | 120 BCD |
| Tooth Count: | 52/50 Tooth |
| Width: |
3/32"
|
| Condition: |
OK
|
| SKU: | CR121 |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
53t Unbranded Drilled Vintage Chainring
£35.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
3/32" is used for double & triple chainsets but can also be used for single ring chainsets. 1/8" is generally used for track chainsets & some single chainsets too.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Bolt Circle Diameter: | 144 BCD |
| Tooth Count: | 53 Tooth |
| Width: |
3/32"
|
| Condition: |
Good
|
| SKU: | CR130_VTG |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
54T Stronglight Vintage Chainring
£25.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
All chainrings are standard 3/32" for road use unless stated.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Tooth Count: | 54 |
| BCD: | 122 BCD |
| Condition: | Good/OK |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
55T Unknown Vintage Chainring
£35.00
Most of our chainrings are used but we only keep ones with life left in them, and they are accurately graded depending on physical wear.
All chainrings are standard 3/32" for road use unless stated.
Please be sure to check that the BCD (Bolt Circle Diameter) matches that of your crankset, otherwise the chainring will not fit. If you need help measuring your BCD, good ol' Sheldon Brown will be glad to be of assistance here: http://www.sheldonbrown.com/gloss_bo-z.html
SIZING & CONDITION
| Tooth Count: | 55 |
| BCD: | 151 BCD |
| Condition: | Good |
SHIPPING, TAXES & RETURNS
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import duties to pay upon receipt (even with the new post-Brexit trade deals, some countries may still charge you import VAT & clearance fees, so please bear this in mind when purchasing).
View full product details
57.5cm J.P Van Poppel's Vintage Gazelle Champion Mondial
£2,750.00
What an honour.
This right here is Jean-Paul Van Poppel's very own team bike from his time with the amateur Gazelle-Vredestein-Campagnolo team of 1983/1984.
Van Poppel, one of the most fierce sprinters of all times, became pro in 1985 for Team Skala, and went on to win points classification in the Tour De France just a few years later in 1987.
The bike came with the number 77 race plate, it's been cleaned & polished throughout but it remains pretty much original to the condition we got it. There is some damage to the front end, with a little bit of rippling underneath the down tube and some flaking of paint near the top tube internal cable routing as you can see from the photos. Most-likely crashed by the man himself, but otherwise the paint & parts are in amazing condition. Given the crash damage it's obviously one for the wall, which is where it belongs really, it's a genuine show-piece and genuinely one of a kind.
Obviously the price tag is high, but this is a very special bike and if there was no crash damage it would have to be twice the price, so it has been taken into consideration.
Check out the photos below or give us a call to arrange to see it in the flesh as it doesn't currently live in our London shop.
| OVERVIEW: | |
| Seat Tube (ctc): | 57.5 cm |
| Top Tube: (ctc): | 56 cm |
| Head Tube: | 160 mm |
| Standover: | 82 cm |
| Weight: | 9.6 kg |
| Tubing: | Reynolds 753 |
| Dropouts: | Campagnolo |
| Country: | Netherlands |
| Year: | 1983/84 |
| FULL SPEC: | |
| Brake Levers: | Campagnolo Super Record |
| Brake Calipers: | Campagnolo Nuovo Record |
| Crankset: | Campagnolo Super Record 172.5mm 52/42 |
| Shifters: | Simplex |
| Rear Derailleur: | Campagnolo Super record |
| Front Derailleur: | Campagnolo Super Record |
| Freewheel: | Shimano UG 6 Speed |
| Chain: | Sedis 6 Speed |
| Pedals: | Please Select From Drop Down |
| Bottom Bracket: | Campagnolo Record |
| Hubs: | Campagnolo Record |
| Rims: | Mavic MA40 (700c) |
| Tyres: | NOS Gazelle Vuelta (20mm Width) |
| Headset: | Shimano 600 Sealed Bearings |
| Handlebars: | Cinelli Campione Del Mondo |
| Stem: |