£25.00
Unbranded vintage cable set (outer casing and inner wires), most likely in production during the 1970s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
Made up of vintage new old stock housing with new inner cables. Complete with ferrules and end caps, and with plenty of cable outer for even the largest frames.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cables!
OVERVIEW
TECHNICAL INFO
Position - rear cables need to be longer than fronts, this is the only difference so cables long enough for the rear can also be used on the front.
Cable Type - brake and gear cables have different specifications and are not interchangeable.
Casing Width - the outside diameter of the housing. Brake cable housing is a little wider in diameter than gear, this is to accommodate the slightly thicker inner cables.
Length - it's important to check the cables are long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.
Brake End Nipple Type - Pear' type cable ends step down in size to allow them to be used with drop bar brake levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.
End Nipple Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.
£35.00
Vittoria Rubino Pro folding tyres, hailing from Italy and in production during the 2010s. Made from rubber and weighing in at 480 grams (the weight and price displayed are for a pair of tyres). A fine choice for keeping your bike authentic, but also great for any other compatible bike.
The tyres have been thoroughly checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Size - this is the manufacturer’s sizing and must match the size or your wheels. This can be confusing as tyres have had different sizing systems over the years, and there are many (sometimes conflicting) sizes available. For this reason it’s important to check the ISO diameter too for clarification, especially for 26” wheels.
Bike Type - the type of bike the tyres were designed to be used on. Road tyres will generally be narrow with minimal tread, touring tyres wider with a bit more grip in the tread, and cyclocross & MTB tyres wider still (especially the latter), with a much more pronounced tread pattern.
ISO Diameter - this relates to the diameter of the wheel rims at the point where the tyres are seated (bead seat diameter). This is a universal measurement, often displayed on tyres as 28-622 or similar, 28 referring to the tyre width and 622 being the ISO diameter in millimetres.
TPI - stands for threads per inch and refers to the thread count of the tyre casings. A high thread count usually means more supple and lighter tyres, this can be anything as high as 320 tpi. We can’t always provide this information however, as it’s not always possible to know for sure.
£35.00
Vittoria Rubino Pro folding tyres, hailing from Italy and in production during the 2010s. Made from rubber and weighing in at 480 grams (the weight and price displayed are for a pair of tyres). A fine choice for keeping your bike authentic, but also great for any other compatible bike.
The tyres have been thoroughly checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Size - this is the manufacturer’s sizing and must match the size or your wheels. This can be confusing as tyres have had different sizing systems over the years, and there are many (sometimes conflicting) sizes available. For this reason it’s important to check the ISO diameter too for clarification, especially for 26” wheels.
Bike Type - the type of bike the tyres were designed to be used on. Road tyres will generally be narrow with minimal tread, touring tyres wider with a bit more grip in the tread, and cyclocross & MTB tyres wider still (especially the latter), with a much more pronounced tread pattern.
ISO Diameter - this relates to the diameter of the wheel rims at the point where the tyres are seated (bead seat diameter). This is a universal measurement, often displayed on tyres as 28-622 or similar, 28 referring to the tyre width and 622 being the ISO diameter in millimetres.
TPI - stands for threads per inch and refers to the thread count of the tyre casings. A high thread count usually means more supple and lighter tyres, this can be anything as high as 320 tpi. We can’t always provide this information however, as it’s not always possible to know for sure.
£30.00
Shimano Dura-Ace front wheel skewer (or hub spindle if you prefer), hailing from Japan and in production from the 1980s to the 1990s. Made from steel and weighing in at 91 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The skewer's been cleaned, checked by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£25.00
Specialites T.A. 'Plum' water bottle cages (or bidon holders if you prefer), hailing from France and in production from the 1980s to the 1990s (yet still new & unused after all this time). Made from aluminium/plastic and weighing in at 92 grams (the weight and price displayed are for a pair of cages). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
These are the final versions of the Plum lightweight bottle cage, featuring wrap-around 'sleeves' and punched dimples on the rear of the frame mounts, replacing the exposed welded construction of the previous design.
If you're taking part in L'Eroica or a similar vintage event, these are of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong bottle carriers!
OVERVIEW
TECHNICAL INFO
Cage Fixing - most bottle cages will be designed to fix to the frame, although some rare older ones mount to the handlebars and/or stem. If your frame doesn't have any bottle cage braze-ons to fix to you'll need clamp-on bottle cages.
Bottle Fit - almost all cycling bottles measure between 70 - 75 mm in diameter so this is the standard bottle cage size, the only rather rare exceptions are some old Elite bottles that require a 66 mm cage, the more recent oversized ones and of course the funny shaped aero ones that only accept the bottle they were made for.
£25.00
Vredestein visor, hailing from The Netherlands and in production during the 1980s (yet still new & unused after all this time). An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
OVERVIEW
TECHNICAL INFO
£30.00
Vredestein visor, hailing from The Netherlands and in production during the 1980s (yet still new & unused after all this time). An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
OVERVIEW
TECHNICAL INFO
£25.00
Sun Ringle wheel skewers (or hub spindles if you prefer), hailing from the United States and in production during the 2000s. Made from aluminium/steel and weighing in at 105 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame & fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£40.00
Campagnolo Nuovo/Super Record rear wheel skewer (or hub spindle if you prefer), hailing from Italy and in production from the 1960s to the 1970s. The design is of the ’pre-CPSC’ era produced until around 1978. Made from steel and weighing in at 83 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!
The skewer's been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£25.00
Cambio Rino rear wheel skewer (or hub spindle if you prefer), hailing from Italy and in production from the 1970s to the 1980s. Made from steel and weighing in at 86 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!
The skewer's been cleaned, checked by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£40.00
Campagnolo Nuovo/Super Record rear wheel skewer (or hub spindle if you prefer), hailing from Italy and in production from the 1960s to the 1970s. The design is of the ’pre-CPSC’ era produced until around 1978. Made from steel and weighing in at 87 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!
The skewer's been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£45.00
Decca Meubelen Nibema - Bakkerij Franssen cycling jersey, hailing from Belgium and likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£45.00
Tecnoluan Piemme Autoricambi - Timec - Parkpre cycling jersey, hailing from Italy and likely made in the 1990s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£40.00
MOA Sport cycling jersey, hailing from Italy and likely made in the 1970s given the style (yet still new & unused after all this time). An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!
OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Blacky Futura cycling jersey, hailing from Switzerland and likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Vintage cycling jersey, likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£25.00
Best Radical Wear cycling jersey, likely made in the 1990s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as OK condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£40.00
Cicli Debruyne - Assubel - Lokaal Edelweiss Klerken cycling jersey, hailing from Belgium and likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Gonso cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Key West - Easy Walk Ocean Club cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Vintage cycling jersey, hailing from Germany and likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Giessegi cycling jersey, hailing from Italy and likely made in the 1990s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£40.00
Shimano cycling jersey, hailing from Italy and likely made in the 1990s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Gonso Schulz - Das Radhaus von Ettenheim cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Vintage cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Loffler cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£30.00
Sportful cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as OK condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Gonso cycling jersey, hailing from Germany and likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Blacky cycling jersey, hailing from Switzerland and likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Giessegi cycling jersey, hailing from Italy and likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Martinage Annemasse TAC cycling jersey, hailing from France and likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Noret cycling jersey, hailing from France and likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Decathlon cycling jersey, likely made in the 1990s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£25.00
Gonso cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as OK condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Emyco Sport Varo - Wielerclub Guidon cycling jersey, hailing from The Netherlands and likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Vintage cycling jersey, hailing from Germany and likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Decathlon cycling jersey, likely made in the 1990s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£25.00
Basic cycling jersey, hailing from Italy and likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as OK condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£25.00
Boffler Bike Wear cycling jersey, hailing from Austria and likely made in the 1990s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as OK condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Fast cycling jersey, hailing from Italy and likely made in the 1990s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Vintage cycling jersey, likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£40.00
Tinazzi Sport 'DRT' cycling jersey, hailing from Italy and likely made in the 1990s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£40.00
Vintage cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Vintage cycling jersey, hailing from Germany and likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£40.00
Vintage cycling jersey, hailing from Germany and likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£40.00
Medico cycling jersey, likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£30.00
Vermarc cycling jersey, likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Vintage cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£35.00
Silca Impero bicycle pump, hailing from Italy and in production from the 1970s to the 1980s. An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!
The pump's been thoroughly checked, tested and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.
Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.
Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!
Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.
£40.00
Silca Impero bicycle pump, hailing from Italy and in production during the 1980s (yet still new & unused after all this time). An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!
OVERVIEW
TECHNICAL INFO
Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.
Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.
Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!
Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.
SUBSCRIBE TO GET THE FIRST SCOOP
Exclusive content, new products, subscriber only promotions. Delivered to your inbox by tiny cyclists, every few weeks.
Don't worry, you can unsubscribe at any time.
PEDAL PEDLAR
T: 02036758003 // E: info@pedalpedlar.co.uk
© 2026 Pedal Pedlar.
Ecommerce Software by Shopify