£46.75 £55.00
Shimano 105 left (non-drive side) crank arm, hailing from Japan and in production during the 1990s (yet still new & unused after all this time). Made from aluminium and weighing in at 255 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Crank Arm Length - this is measured from the absolute centre of the bottom bracket hole to the centre of the hole for the pedal.
Pedal Threads - the pattern of the thread that your pedals screw into, this is usually stamped on the pedals themselves and most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).
Bottom Bracket Type - ‘square taper’, as the name suggests have a square shaped axle that slots into the crank and ‘cottered’ axles are round and secured by pins - pretty much every bike up until the 1990s would use one of these, cottered being the much earlier system. Since then, different manufacturers have introduced their own systems that are not interchangeable so you must use a crank that matches.
£21.25 £25.00
Velox Top Ribbon bar tape (or grip, or wrap if you prefer), hailing from France and in production from the 1990s to the 2000s (yet still new & unused after all this time). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£21.25 £25.00
Silva Splash bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£23.75 £25.00
Silva Splash bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£21.25 £25.00
3TTT Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1990s to the 2000s (yet still new & unused after all this time). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£21.25 £25.00
Cinelli Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£21.25 £25.00
Wheeler musette (or feed bag if you prefer), hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£18.00 £20.00
Classic Tacconi Sport / Carrera / Santini musette (or feed bag if you prefer), most likely in production during the 1990s. An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
The bag's been checked over and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£31.50 £35.00
Vintage Cicli Concorde / Ultima musette (or feed bag if you prefer), most likely in production from the 1980s to the 1990s. An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
The bag's been checked over and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£18.00 £20.00
Classic Rabobank 'Ronde van Midden Nederland' musette (or feed bag if you prefer), most likely in production during the 1990s. An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
The bag's been checked over and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£20.25 £23.00
Santini Maglificio Sportivo musette (or feed bag if you prefer), hailing from Italy and in production during the 1990s. An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
The bag's been checked over and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£22.50 £25.00
Classic Rabobank musette (or feed bag if you prefer), most likely in production during the 1990s. An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
The bag's been checked over and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£12.75 £15.00
Classic W Cup musette (or feed bag if you prefer), most likely in production during the 1990s (yet still new & unused after all this time). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£31.50 £35.00
Panasonic Tour de Suisse 1991 kit bag (or gym sack if you prefer), hailing from Japan and in production during the 1990s. An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
The bag's been checked over and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£22.50 £25.00
Campagnolo wheel bag (or carrier if you prefer), hailing from Italy and in production during the 1990s. An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
The bag's been checked over and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£21.25 £25.00
Miche wheel bag (or carrier if you prefer), hailing from Italy and in production from the 1990s to the 2000s (yet still new & unused after all this time). An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
OVERVIEW
TECHNICAL INFO
£80.75 £95.00
Modolo wheel bag (or carrier if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£34.00 £40.00
Campagnolo wheel bag (or carrier if you prefer), hailing from Italy and in production from the 1990s to the 2000s (yet still new & unused after all this time). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£25.50 £30.00
Campagnolo wheel bag (or carrier if you prefer), hailing from Italy and in production from the 1990s to the 2000s (yet still new & unused after all this time). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£21.25 £25.00
Rigida wheel bag (or carrier if you prefer), hailing from France and in production from the 1980s to the 1990s (yet still new & unused after all this time). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£67.50 £75.00
Sidi cycling kit bag (or duffle, or travel bag), hailing from Italy and in production during the 1990s. An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
The bag's been checked over and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£112.50 £125.00
Eddy Merckx cycling kit bag (or duffle, or travel bag), hailing from Belgium and in production from the 1980s to the 1990s. An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
The bag's been checked over and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£11.25 £12.50
Freeway triangle frame bag, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time). An excellent choice for classic bikes, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£14.88 £18.00
Roto triangle frame bag, hailing from Italy and in production during the 1980s (yet still new & unused after all this time). An excellent choice for vintage bikes, but great for bikes of the non-vintage variety too!
OVERVIEW
TECHNICAL INFO
£31.88 £38.00
Reydel saddle bag (or seat pack if you prefer), hailing from France and in production during the 1970s (yet still new & unused after all this time). An excellent choice for vintage bikes, but great for bikes of the non-vintage variety too!
OVERVIEW
TECHNICAL INFO
£34.00 £40.00
Mafac saddle bag (or seat pack if you prefer), hailing from France and in production during the 1970s (yet still new & unused after all this time). An excellent choice for vintage bikes, but great for bikes of the non-vintage variety too!
OVERVIEW
TECHNICAL INFO
£19.00 £20.00
Outback 1025 saddle bag (or seat pack if you prefer), hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time). An excellent choice for classic bikes, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£19.00 £20.00
Radsport Fink saddle bag (or seat pack if you prefer), hailing from Germany and in production during the 1990s (yet still new & unused after all this time). An excellent choice for classic bikes, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£17.00 £20.00
Radsport Fink saddle bag (or seat pack if you prefer), hailing from Germany and in production during the 1990s (yet still new & unused after all this time). An excellent choice for classic bikes, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£25.50 £30.00
Zefal Kanga saddle bag (or seat pack if you prefer), hailing from France and in production during the 2000s. An excellent choice for classic bikes, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£21.25 £25.00
Zefal Kola saddle bag (or seat pack if you prefer), hailing from France and in production during the 2000s. An excellent choice for classic bikes, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£19.13 £23.00
Outback 1047 saddle bag (or seat pack if you prefer), hailing from Taiwan and in production from the 1990s to the 2000s (yet still new & unused after all this time). An excellent choice for classic bikes, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£63.75 £75.00
Shimano Deore II flat bar brake levers (or handles if you prefer), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 267 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£21.25 £25.00
Tektro 361A flat bar brake levers (or handles if you prefer), hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 179 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£45.00 £50.00
Shimano Deore XT flat bar brake levers (or handles if you prefer), hailing from Japan and in production during the 1980s. Made from aluminium/steel and weighing in at 312 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The brake levers have been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£76.50 £85.00
CLB Route Speciale flat bar brake levers (or handles if you prefer), hailing from France and in production from the 1950s to the 1960s. Made from aluminium and weighing in at 139 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong brake levers!
The brake levers have been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£67.50 £75.00
CLB Route Speciale flat bar brake levers (or handles if you prefer), hailing from France and in production from the 1960s to the 1970s. Made from aluminium and weighing in at 139 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong brake levers!
The brake levers have been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£58.50 £65.00
CLB Route Speciale flat bar brake levers (or handles if you prefer), hailing from France and in production from the 1960s to the 1970s. Made from aluminium and weighing in at 182 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong brake levers!
The brake levers have been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£67.50 £75.00
Unbranded vintage flat bar brake levers (or handles if you prefer), most likely in production from the 1940s to the 1950s. Made from aluminium and weighing in at 145 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The brake levers have been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£31.50 £35.00
Shimano Deore flat bar brake levers (or handles if you prefer), hailing from Japan and dating back to 1987. Made from aluminium/steel and weighing in at 316 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The brake levers have been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£22.50 £25.00
Tektro flat bar brake levers (or handles if you prefer), hailing from Taiwan and in production during the 1990s. Made from aluminium and weighing in at 192 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
The brake levers have been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£40.50 £45.00
Mafac Ville flat bar brake levers (or handles if you prefer), hailing from France and in production from the 1970s to the 1980s. Made from aluminium/resin and weighing in at 148 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong brake levers!
The brake levers have been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£58.50 £65.00
Shimano Z Series flat bar brake levers (or handles if you prefer), hailing from Japan and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 267 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£72.25 £85.00
Suntour XCD flat bar brake levers (or handles if you prefer), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from aluminium/rubber and weighing in at 222 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.
£12.75 £15.00
Zefal 43 toe clips (or pedal cages if you prefer), hailing from France and in production during the 1990s (yet still new & unused after all this time!). Made from plastic and weighing in at 79 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£25.50 £30.00
Christophe 47 M toe clips (or pedal cages if you prefer), hailing from France and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from steel and weighing in at 115 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£13.50 £15.00
Roto chainstay protector (or frame guard if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£13.50 £15.00
Roto chainstay protector (or frame guard if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£9.00 £10.00
Minoura Chain Plate chainstay protector, hailing from Japan and in production during the 1990s (yet still new & unused after all this time!). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£9.00 £10.00
Minoura Chain Plate chainstay protector, hailing from Japan and in production during the 1990s (yet still new & unused after all this time!). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
SUBSCRIBE TO GET THE FIRST SCOOP
Exclusive content, new products, subscriber only promotions. Delivered to your inbox by tiny cyclists, every few weeks.
Don't worry, you can unsubscribe at any time.
PEDAL PEDLAR
T: 02036758003 // E: info@pedalpedlar.co.uk
© 2026 Pedal Pedlar.
Ecommerce Software by Shopify