£36.00 £40.00
Campagnolo Record set of chainring bolts (or screws if you prefer), hailing from Italy and in production from the 1980s to the 1990s. Made from steel and weighing in at 27 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The chainring bolts and backs have been cleaned, checked and graded as mint condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Chainring Count - the number of chainrings the bolts are designed to fit, this must be the same as the number of chainrings you are using.
Crank Type - Most cranks require the standard 5-bolt sets that consist of 5 bolts with backs that slot into the rear of the crank spider, there are also some less common cranks with 3 arms that require the 3-arm chainring bolts. Specialites T.A. 'Professionel 5 Vis' and Stronglight '49D' type cranks require special 50.4 BCD chainring bolts that are specific to these crank designs.
Mount Type - most bolts simply fix the chainring to the crank, but some cranks require bolts to fix one chainring to another.
Back Nut Length (Excluding Head) - the more chainrings your crank has the longer the bolts and nuts need to be. We exclude the head part from the measurement (the bit that often sits recessed in back of the chainring).
£112.50 £125.00
Campagnolo Record / Gran Sport a pair of wheel skewers (or hub spindles if you prefer), hailing from Italy and in production from the 1950s to the 1960s. Made from steel and weighing in at 165 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewers!
The skewers have been cleaned, checked by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame & fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£34.00 £40.00
Miche a pair of wheel skewers (or hub spindles if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Made from steel/plastic and weighing in at 155 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewers!
OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame & fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£76.50 £85.00
Campagnolo Nuovo/Super Record a pair of wheel skewers (or hub spindles if you prefer), hailing from Italy and in production from the 1970s to the 1980s. The design is of the ’post-CPSC’ era produced from around 1978 onwards. Made from steel and weighing in at 174 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewers!
The skewers have been cleaned, checked by one of our mechanics and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame & fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£19.13 £22.50
Sugino crankset fixing bolts (or bottom bracket screws if you prefer), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from steel and weighing in at 30 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank bolts!
OVERVIEW
TECHNICAL INFO
Crank Bolt Type - 15 mm hex bolts used to be standard but some older TA, Stronglight and Zeus cranks used a larger 16 mm bolt, plus a few Japanese makers used a smaller 14 mm hex head. Allen key types were introduced in the 1980s and some are self-extracting, which means the crank removes itself when you undo the bolts.
Crank Bolt Thread - All square taper bottom brackets have a standard M8 x 1 mm thread, the only different thread types you’ll find on crank bolts are the much larger M12 & M15 bolts that are specifically for Octalink and ISIS bottom brackets.
£15.75 £17.50
Sugino crankset fixing bolts (or bottom bracket screws if you prefer), hailing from Japan and in production from the 1980s to the 1990s. Made from steel and weighing in at 27 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong crank bolts!
The crank bolts have been cleaned, checked and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Crank Bolt Type - 15 mm hex bolts used to be standard but some older TA, Stronglight and Zeus cranks used a larger 16 mm bolt, plus a few Japanese makers used a smaller 14 mm hex head. Allen key types were introduced in the 1980s and some are self-extracting, which means the crank removes itself when you undo the bolts.
Crank Bolt Thread - All square taper bottom brackets have a standard M8 x 1 mm thread, the only different thread types you’ll find on crank bolts are the much larger M12 & M15 bolts that are specifically for Octalink and ISIS bottom brackets.
£36.00 £40.00
Specialites T.A. 31 crankset dust caps (or bolt covers if you prefer), hailing from France and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 14 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong dust covers!
OVERVIEW
TECHNICAL INFO
Crank Thread - 22 mm is the standard thread for almost all cotterless crank arms, the only exceptions are some Stronglight cranks made up until the early 1980s, and Specialites T.A. Campagnolo produced some self-extracting crank bolts with covers that had a reverse thread.
£34.00 £40.00
Specialites T.A. 31 crankset dust caps (or bolt covers if you prefer), hailing from France and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from steel and weighing in at 17 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong dust covers!
OVERVIEW
TECHNICAL INFO
Crank Thread - 22 mm is the standard thread for almost all cotterless crank arms, the only exceptions are some Stronglight cranks made up until the early 1980s, and Specialites T.A. Campagnolo produced some self-extracting crank bolts with covers that had a reverse thread.
£29.75 £35.00
Silva seat post binder bolt (to clamp the frame around the seat pin), hailing from Italy and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from stainless steel and weighing in at 10 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Clamp Opening - the minimum and maximum distance between the inside of the nut and bolt heads. The minimum is measured with the bolt tightened as much as possible (for hex head types this may mean the bolt end will stick quite far out of the nut). For the maximum opening we ensure 5-6 mm of thread remainis in the nut for a secure fixing.
Outer Diameter - the part that goes through the frame, most steel frames will take an 8 mm bolt whereas early lugged aluminium frames often have a larger hole that takes a 10 mm bolt diameter.
Bolt Fixing Type - some binder bolts have tightening mechanisms on both sides to secure the seatpost in the frame. Single sided bolts need something else to help; some have knurled parts that grip the inside of the bolt hole, others have a small notched 'key' locator that lines up with a cut-out in the frame (if you have one).
£13.50 £15.00
Sugino seat post binder bolt (to clamp the frame around the seat pin), hailing from Japan and in production from the 1970s to the 1980s. Made from steel and weighing in at 12 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost binder bolt!
The seatpost binder bolt's been cleaned, checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Clamp Opening - the minimum and maximum distance between the inside of the nut and bolt heads. The minimum is measured with the bolt tightened as much as possible (for hex head types this may mean the bolt end will stick quite far out of the nut). For the maximum opening we ensure 5-6 mm of thread remainis in the nut for a secure fixing.
Outer Diameter - the part that goes through the frame, most steel frames will take an 8 mm bolt whereas early lugged aluminium frames often have a larger hole that takes a 10 mm bolt diameter.
Bolt Fixing Type - some binder bolts have tightening mechanisms on both sides to secure the seatpost in the frame. Single sided bolts need something else to help; some have knurled parts that grip the inside of the bolt hole, others have a small notched 'key' locator that lines up with a cut-out in the frame (if you have one).
£13.50 £15.00
Andrew Hague seat post binder bolt (to clamp the frame around the seat pin), hailing from Great Britain and in production during the 1970s. Made from steel and weighing in at 12 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong seatpost binder bolt!
The seatpost binder bolt's been cleaned, checked and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Clamp Opening - the minimum and maximum distance between the inside of the nut and bolt heads. The minimum is measured with the bolt tightened as much as possible (for hex head types this may mean the bolt end will stick quite far out of the nut). For the maximum opening we ensure 5-6 mm of thread remainis in the nut for a secure fixing.
Outer Diameter - the part that goes through the frame, most steel frames will take an 8 mm bolt whereas early lugged aluminium frames often have a larger hole that takes a 10 mm bolt diameter.
Bolt Fixing Type - some binder bolts have tightening mechanisms on both sides to secure the seatpost in the frame. Single sided bolts need something else to help; some have knurled parts that grip the inside of the bolt hole, others have a small notched 'key' locator that lines up with a cut-out in the frame (if you have one).
£18.75 £25.00
3TTT Nastro Resina bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£22.50 £30.00
Celo-Cinta Professionale bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£15.00 £20.00
3TTT Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1990s to the 2000s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
3TTT Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1990s to the 2000s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£12.75 £15.00
3TTT Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1990s to the 2000s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£14.25 £15.00
Silva bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£13.50 £15.00
Silva bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£15.00 £20.00
3TTT 3 Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£9.38 £13.00
Bluemels bar tape (or grip, or wrap if you prefer), hailing from Great Britain and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
GES Flash Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£22.50 £30.00
Ciclolinea Pelten Shade bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£13.50 £15.00
GES Race Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£15.00 £20.00
GES Race Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
GES Flash Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
GES Flash Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
3TTT bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£15.00 £20.00
3TTT bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£23.75 £25.00
3TTT Celo-Nastro Professionale bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£7.50 £10.00
Ciclolinea bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£22.50 £30.00
Benotto Celo-Cinta Professionale bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£18.75 £25.00
Benotto Celo-Cinta Professionale bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£18.75 £25.00
Benotto Celo-Cinta Professionale bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£22.50 £30.00
Benotto Celo-Cinta Professionale bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£9.38 £12.50
Bluemels bar tape (or grip, or wrap if you prefer), hailing from Great Britain and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£7.50 £10.00
Co Union bar tape (or grip, or wrap if you prefer), hailing from Taiwan and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£22.50 £30.00
DPS Celo-Nastro Professionale bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
Unbranded vintage bar tape (or grip, or wrap if you prefer), most likely in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£22.50 £30.00
Velox Tressostar Competition bar tape (or grip, or wrap if you prefer), hailing from France and in production from the 1960s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£22.50 £30.00
Velox Tressostar Competition bar tape (or grip, or wrap if you prefer), hailing from France and in production from the 1960s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
Selev Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
£15.00 £20.00
Top Ribbon bar tape (or grip, or wrap if you prefer), hailing from France and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£18.75 £25.00
Ciclolinea Pelten Graphic bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£26.25 £35.00
Ambrosio Bike Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£11.25 £15.00
Georges Sorel bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£18.75 £25.00
Georges Sorel bar tape (or grip, or wrap if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£15.00 £20.00
Iscaselle Dainy bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£15.00 £20.00
GES Fluor Ribbon bar tape (or grip, or wrap if you prefer), hailing from Spain and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£30.00 £40.00
3TTT Mutant ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 250 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.
Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.
Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).
Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.
£37.50 £50.00
3TTT Mutant ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 272 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.
Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.
Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).
Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.
SUBSCRIBE TO GET THE FIRST SCOOP
Exclusive content, new products, subscriber only promotions. Delivered to your inbox by tiny cyclists, every few weeks.
Don't worry, you can unsubscribe at any time.
PEDAL PEDLAR
T: 02036758003 // E: info@pedalpedlar.co.uk
© 2026 Pedal Pedlar.
Ecommerce Software by Shopify