£20.00
Unbranded vintage cable set (outer casing and inner wires), most likely in production during the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
Made up of original NOS lined housing with new inner cables, these sets make a great substitute for the iconic Campagnolo Nuovo/Super Record cables from the 70s/80s. Complete with ferrules and end caps, and with plenty of cable outer for even the largest frames.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cables!
OVERVIEW
TECHNICAL INFO
Position - rear cables need to be longer than fronts, this is the only difference so cables long enough for the rear can also be used on the front.
Cable Type - brake and gear cables have different specifications and are not interchangeable.
Casing Width - the outside diameter of the housing. Brake cable housing is a little wider in diameter than gear, this is to accommodate the slightly thicker inner cables.
Length - it's important to check the cables are long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.
Brake End Nipple Type - Pear' type cable ends step down in size to allow them to be used with drop bar brake levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.
End Nipple Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.
£22.50
Casiraghi cable set (outer casing and inner wires), hailing from Italy and in production from the 1980s to the 1990s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
Made up of original NOS Casiraghi Industries housing with new inner cables. Complete with ferrules and end caps, and with plenty of cable outer for even the largest frames.
OVERVIEW
TECHNICAL INFO
Position - rear cables need to be longer than fronts, this is the only difference so cables long enough for the rear can also be used on the front.
Cable Type - brake and gear cables have different specifications and are not interchangeable.
Casing Width - the outside diameter of the housing. Brake cable housing is a little wider in diameter than gear, this is to accommodate the slightly thicker inner cables.
Length - it's important to check the cables are long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.
Brake End Nipple Type - Pear' type cable ends step down in size to allow them to be used with drop bar brake levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.
End Nipple Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.
£20.00
Unbranded vintage cable set (outer casing and inner wires), most likely in production during the 1970s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
Made up of vintage new old stock housing with new inner cables. Complete with ferrules and end caps, and with plenty of cable outer for even the largest frames.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cables!
OVERVIEW
TECHNICAL INFO
Position - rear cables need to be longer than fronts, this is the only difference so cables long enough for the rear can also be used on the front.
Cable Type - brake and gear cables have different specifications and are not interchangeable.
Casing Width - the outside diameter of the housing. Brake cable housing is a little wider in diameter than gear, this is to accommodate the slightly thicker inner cables.
Length - it's important to check the cables are long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.
Brake End Nipple Type - Pear' type cable ends step down in size to allow them to be used with drop bar brake levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.
End Nipple Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.
£20.00
Zefal TX Mini bicycle pump, hailing from France and in production during the 1990s (yet still new & unused after all this time). An excellent choice for classic cycling enthusiasts, but great for cyclists of the non-classic variety too!
OVERVIEW
TECHNICAL INFO
Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.
£10.00
Specialites T.A. 'Plum' water bottle cage (or bidon holder if you prefer), hailing from France and in production during the 1980s. Made from aluminium/plastic and weighing in at 49 grams. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
First introduced in the 1970s and originally available in black & silver only, this version of the Plum lightweight bottle cage features the exposed welded construction favoured for its strength and durability. The later T.A. logo on the black plastic tab was introduced in the 1980s when it became available in a choice of colours.
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong bottle carrier!
The bottle cage has been checked for damage, thoroughly cleaned and graded as OK condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
TECHNICAL INFO
Cage Fixing - most bottle cages will be designed to fix to the frame, although some rare older ones mount to the handlebars and/or stem. If your frame doesn't have any bottle cage braze-ons to fix to you'll need a clamp-on bottle cage.
Bottle Fit - almost all cycling bottles measure between 70 - 75 mm in diameter so this is the standard bottle cage size, the only rather rare exceptions are some old Elite bottles that require a 66 mm cage, the more recent oversized ones and of course the funny shaped aero ones that only accept the bottle they were made for.
£12.50
Minoura water bottle cage (or bidon holder if you prefer), hailing from Japan and in production during the 1990s. Made from aluminium and weighing in at 83 grams. The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
The bottle cage has been checked for damage, thoroughly cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
TECHNICAL INFO
Cage Fixing - most bottle cages will be designed to fix to the frame, although some rare older ones mount to the handlebars and/or stem. If your frame doesn't have any bottle cage braze-ons to fix to you'll need a clamp-on bottle cage.
Bottle Fit - almost all cycling bottles measure between 70 - 75 mm in diameter so this is the standard bottle cage size, the only rather rare exceptions are some old Elite bottles that require a 66 mm cage, the more recent oversized ones and of course the funny shaped aero ones that only accept the bottle they were made for.
£12.50
Vintage water bottle cage (or bidon holder if you prefer), most likely in production during the 1980s. Made from aluminium and weighing in at 58 grams. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
The bottle cage has been checked for damage, thoroughly cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
TECHNICAL INFO
Cage Fixing - most bottle cages will be designed to fix to the frame, although some rare older ones mount to the handlebars and/or stem. If your frame doesn't have any bottle cage braze-ons to fix to you'll need a clamp-on bottle cage.
Bottle Fit - almost all cycling bottles measure between 70 - 75 mm in diameter so this is the standard bottle cage size, the only rather rare exceptions are some old Elite bottles that require a 66 mm cage, the more recent oversized ones and of course the funny shaped aero ones that only accept the bottle they were made for.
£20.00
Vintage cap, likely made in the 1980s/1990s given the style (yet still new & unused after all this time). An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Vintage cap, likely made in the 1980s/1990s given the style (yet still new & unused after all this time). An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£15.00
Reynolds cap, likely made in the 2010s given the style. An excellent choice for wearing on your bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Classic QuickStep - Innergetic cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Classic Topsport Vlaanderen - Mercator cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Omega Pharma - Lotto cap, likely made in the 2010s given the style. An excellent choice for wearing on your bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Classic QuickStep - Innergetic cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Classic Acqua & Sapone - Caffe Mokambo cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Classic CSF Group - Navigare- Colnago cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Classic Vacansoleil - Batavus - SMS Santini cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Classic Tonissteiner - Colnago - Skoda cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Classic Chocolade Jacques - Topsport Vlaanderen - Merckx cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Classic Amore & Vita - McDonald's - Fanini cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£20.00
Classic Selle Italia - Serramenti Diquigiovanni - Santini cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
OVERVIEW
DETAIL
Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.
Construction - the number of panels the cap body is made up of, not including the peak.
£7.50
Joytech front wheel skewer (or hub spindle if you prefer), hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time). Made from steel and weighing in at 99 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£20.00
Campagnolo Xenon front wheel skewer (or hub spindle if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time). Made from steel/plastic and weighing in at 71 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your fork's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£17.50
Zeus Criterium rear wheel skewer (or hub spindle if you prefer), hailing from Spain and in production during the 1970s. Made from steel and weighing in at 86 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong skewer!
The skewer's been cleaned, checked by one of our mechanics and graded as OK condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.
*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.
Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.
End nut length - the total length of the nut from end to end.
£20.00
Gonso cycling jersey, likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as OK condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£20.00
AFA Competition bicycle pump, hailing from France and in production from the 1970s to the 1980s. An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!
The pump's been thoroughly checked, tested and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.
Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.
Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!
Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.
£20.00
Shimano 600 / Titlist right downtube shifter, hailing from Japan and dating back to 1974. Made from aluminium/steel and weighing in at 58 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong shifter!
The shifter's been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Fixing Type - if you have small mounts on either side of the frame’s down tube you need braze-on shifters, if there are no mounts you’ll need clamp-on (sometimes referred to as band-on). Some 'aero' frames have mounts fixed to the top of the down tube, for these frames you require top mount shifters for the correct boss type (see below).
Shift Type - friction shifters don't click into gear when you change, when they do click it's referred to as indexed shifting. For this to work correctly you must use the same system as your rear derailleur, if you're using friction levers you can mix and match. You don't need to worry about the front derailleur as left downtube shifters aren't indexed.
Speed - the number of cogs at the back the right shifter is designed to be used with. This is important with indexed shifting but with friction shifters you can in theory run any shifters with any speed setup, although the right lever will need to be pulled back further to shift into the larger cogs.
Shifter Boss Type - the shape of the mount (for braze-on fixings only). Campagnolo / ISO is standard and easily identified by the flat sections on either side, usually combined with a square base for the backing stop plates to fit. There are also Shimano ones with a keyhole shaped base and much less common French ones that are round with no flat sections.
Boss Thread Size - M5 (5 mm) is standard for Campagnolo / ISO bosses, but Shimano bosses will often have M4.5 (4.5 mm) threads and the French bosses would likely have 5 x 1 mm threads.
£20.00
Shimano Exage Trail front derailleur (or mech, or changer if you prefer), hailing from Japan and dating back to 1989. Made from aluminium/steel and weighing in at 134 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The derailleur's been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.
Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.
Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.
Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.
Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.
£23.75 £25.00
Schwalbe Black Jack tyres, hailing from Germany. Made from rubber and weighing in at 1360 grams (the weight and price displayed are for a pair of tyres). A fine choice for keeping your modern bike correct, but also great for any other compatible bike.
The tyres have been thoroughly checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Size - this is the manufacturer’s sizing and must match the size or your wheels. This can be confusing as tyres have had different sizing systems over the years, and there are many (sometimes conflicting) sizes available. For this reason it’s important to check the ISO diameter too for clarification, especially for 26” wheels.
Bike Type - the type of bike the tyres were designed to be used on. Road tyres will generally be narrow with minimal tread, touring tyres wider with a bit more grip in the tread, and cyclocross & MTB tyres wider still (especially the latter), with a much more pronounced tread pattern.
ISO Diameter - this relates to the diameter of the wheel rims at the point where the tyres are seated (bead seat diameter). This is a universal measurement, often displayed on tyres as 28-622 or similar, 28 referring to the tyre width and 622 being the ISO diameter in millimetres.
TPI - stands for threads per inch and refers to the thread count of the tyre casings. A high thread count usually means more supple and lighter tyres, this can be anything as high as 320 tpi. We can’t always provide this information however, as it’s not always possible to know for sure.
£23.75 £25.00
CST Super HP tyres, hailing from China and in production during the 1980s. Made from rubber and weighing in at 690 grams (the weight and price displayed are for a pair of tyres). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong tyres!
The tyres have been thoroughly checked and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Size - this is the manufacturer’s sizing and must match the size or your wheels. This can be confusing as tyres have had different sizing systems over the years, and there are many (sometimes conflicting) sizes available. For this reason it’s important to check the ISO diameter too for clarification, especially for 26” wheels.
Bike Type - the type of bike the tyres were designed to be used on. Road tyres will generally be narrow with minimal tread, touring tyres wider with a bit more grip in the tread, and cyclocross & MTB tyres wider still (especially the latter), with a much more pronounced tread pattern.
ISO Diameter - this relates to the diameter of the wheel rims at the point where the tyres are seated (bead seat diameter). This is a universal measurement, often displayed on tyres as 28-622 or similar, 28 referring to the tyre width and 622 being the ISO diameter in millimetres.
TPI - stands for threads per inch and refers to the thread count of the tyre casings. A high thread count usually means more supple and lighter tyres, this can be anything as high as 320 tpi. We can’t always provide this information however, as it’s not always possible to know for sure.
£15.00
REG toe strap buttons (or ends, or caps, or retainers if you prefer), hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from plastic and weighing in at 4 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe strap buttons!
OVERVIEW
TECHNICAL INFO
£11.50
REG toe strap buttons (or ends, or caps, or retainers if you prefer), hailing from Italy and in production from the 1970s to the 1980s. Made from plastic and weighing in at 5 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe strap buttons!
They've been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£20.00
Christophe 516 B toe straps (or pedal straps if you prefer), hailing from France and in production during the 1980s. The straps are blue in colour and made from leather/steel, the perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe straps!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£20.00
Unbranded vintage toe straps (or pedal straps if you prefer), most likely in production from the 1970s to the 1980s. The straps are grey in colour and made from leather, the perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe straps!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£20.00
REG toe straps (or pedal straps if you prefer), hailing from Italy and in production from the 1960s to the 1970s. The straps are black in colour and made from leather/steel, the perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe straps!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£17.50
Christophe 516 T toe straps (or pedal straps if you prefer), hailing from France and in production during the 1990s. The straps are tan in colour and made from leather/steel, the perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too of course!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£8.50
Christophe 516 N toe straps (or pedal straps if you prefer), hailing from France and in production during the 1990s. The straps are black in colour and made from leather/steel, the perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too of course!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£17.50
AFA 511 W toe straps (or pedal straps if you prefer), hailing from France and in production during the 1980s. The straps are white in colour and made from leather/steel, the perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe straps!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£20.00
Christophe 516 T toe straps (or pedal straps if you prefer), hailing from France and in production during the 1990s. The straps are tan in colour and made from leather/steel, the perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too of course!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£12.50
Elite Eclipse toe clips (or pedal cages if you prefer), hailing from Italy and in production during the 1990s. Made from plastic and weighing in at 110 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
The toe clips have been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£12.50
Tioga Power Clip toe clips (or pedal cages if you prefer), hailing from the United States and in production from the 1980s to the 1990s. Made from plastic and weighing in at 77 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The toe clips have been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£12.50
ALE ASSO toe clips (or pedal cages if you prefer), hailing from Italy and in production from the 1970s to the 1980s. Made from steel and weighing in at 56 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£15.00
MKS toe clips (or pedal cages if you prefer), hailing from Japan and in production during the 1990s. Made from steel and weighing in at 74 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
The toe clips have been checked, cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£12.50
MKS toe clips (or pedal cages if you prefer), hailing from Japan and in production during the 1990s. Made from steel and weighing in at 74 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
The toe clips have been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£15.00
Christophe 50 / 506 toe clips (or pedal cages if you prefer), hailing from France and in production from the 1980s to the 1990s. Made from steel and weighing in at 63 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£13.50
Christophe 50 / 506 toe clips (or pedal cages if you prefer), hailing from France and in production from the 1980s to the 1990s. Made from steel and weighing in at 64 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been checked, cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£17.50
Christophe 49 / 496 Z toe clips (or pedal cages if you prefer), hailing from France and in production during the 1980s. Made from alloy and weighing in at 29 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been checked, cleaned and graded as OK condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£17.50
Shimano Dura-Ace set of 2 inner cables (or wires if you prefer), hailing from Japan and in production during the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cables!
OVERVIEW
TECHNICAL INFO
Cable Type - brake and gear cables have different specifications and are not interchangeable.
Length (F/R) - it's important to check the cables are long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.
End Nipple Type - only relevant for brake cables. 'Pear' type cable ends step down in size to allow them to be used with drop bar levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.
End Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.
£12.50
Shimano Deore cable housing (or outer casing if you prefer), hailing from Japan and in production during the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
Designed to house the oversized 2 mm Deore XT inner cables. Comes in one 2.25 metre length with 2 oversized ferrules, enough for full runs to both front & rear brakes.
OVERVIEW
TECHNICAL INFO
Housing Type - brake and gear cables have different specifications and are generally not interchangeable, although older bikes with non-index shifting often used brake housing instead of gear. We'd still recommend using the dedicated front or rear derailleur cable housings for non-index setups whenever possible.
Casing Width - the outside diameter of the housing. Brake cable housing is a little wider in diameter than gear, this is to accommodate the slightly thicker inner cables.
Ferrule Size - if ferrules are included, this measurement is of the outside diameter at the widest part
£17.50
Casiraghi cable housing (or outer casing if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
OVERVIEW
TECHNICAL INFO
Housing Type - brake and gear cables have different specifications and are generally not interchangeable, although older bikes with non-index shifting often used brake housing instead of gear. We'd still recommend using the dedicated front or rear derailleur cable housings for non-index setups whenever possible.
Casing Width - the outside diameter of the housing. Brake cable housing is a little wider in diameter than gear, this is to accommodate the slightly thicker inner cables.
Ferrule Size - if ferrules are included, this measurement is of the outside diameter at the widest part
SUBSCRIBE TO GET THE FIRST SCOOP
Exclusive content, new products, subscriber only promotions. Delivered to your inbox by tiny cyclists, every few weeks.
Don't worry, you can unsubscribe at any time.
PEDAL PEDLAR
T: 02036758003 // E: info@pedalpedlar.co.uk
© 2026 Pedal Pedlar.
Ecommerce Software by Shopify