Under £25

Gonso Short Sleeve Vintage Cycling Jersey

£9.00 £12.00

Our jerseys have been sized to be a snug fit. If you prefer a more relaxed fit we suggest going up a size.

Below you'll find precise measurements of the garment when laid flat so you can compare against your favourite fitting jersey. Please make sure to check the length as well as the chest measurement.

The chest is measured across the front only, from armpit to armpit at the seam. The length is measured down the back only, from top of collar to bottom of hem.

SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, normally within 2-3 days, but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Gonso Short Sleeve Vintage Cycling Jersey

£18.75 £25.00

Our jerseys have been sized to be a snug fit. If you prefer a more relaxed fit we suggest going up a size.

Below you'll find precise measurements of the garment when laid flat so you can compare against your favourite fitting jersey. Please make sure to check the length as well as the chest measurement.

The chest is measured across the front only, from armpit to armpit at the seam. The length is measured down the back only, from top of collar to bottom of hem.

Size:	Small (34 - 37" Chest)
Material:	100% Polyester
Condition:	Very Good

	Cm	Inches
Pit to Pit (Laid Flat):	49	19
Length (Down Back):	71	28

SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, normally within 2-3 days, but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Gonso Tour De Landle 99 Short Sleeve Vintage Cycling Jersey

£13.50 £18.00

Our jerseys have been sized to be a snug fit. If you prefer a more relaxed fit we suggest going up a size.

Below you'll find precise measurements of the garment when laid flat so you can compare against your favourite fitting jersey. Please make sure to check the length as well as the chest measurement.

The chest is measured across the front only, from armpit to armpit at the seam. The length is measured down the back only, from top of collar to bottom of hem.

Size:	Medium (38 - 42" Chest)
Material:	100% Polyester
Condition:	Good

	Cm	Inches
Pit to Pit (Laid Flat):	49	19
Length (Down Back):	71	28

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, normally within 2-3 days, but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Gonso Vintage Cycling Jersey

£15.00 £20.00

Our jerseys have been sized to be a snug fit. If you prefer a more relaxed fit we suggest going up a size.

Below you'll find precise measurements of the garment when laid flat so you can compare against your favourite fitting jersey. Please make sure to check the length as well as the chest measurement.

The chest is measured across the front only, from armpit to armpit at the seam. The length is measured down the back only, from top of collar to bottom of hem.

Size:	Small (34 - 37" Chest)
Material:	100% Polyester
Condition:	Good (Few Snags On Front)

	Cm	Inches
Pit to Pit (Laid Flat):	58	23
Length (Down Back):	75	30

SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, normally within 2-3 days, but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Gran Premio Leather Vintage Black Pedal / Toe Clip Straps

£14.25 £15.00

✓ Original toe straps - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Gran Premio toe straps, hailing from Italy and in production from the 1970s to the 1980s. The straps are black in colour and made from leather/steel, the perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!

If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe straps!

The toe straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Condition - Good
Production Era - 1970s & 1980s
Country - Italian
Material - Leather / Steel
Weight - 50 g
Stock Code - U-STR17V

TECHNICAL INFO

Colour* - Black
Toe Strap Type - Standard
Strap Width - 12 mm
Toe Strap Length - 40 cm

*The colour description is just a guide, please check the photos to get a good idea of the colour too, as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.

Strap Width - measured across one of the straps at its widest point.

Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.

View full product details

Guidoplast Tresse Speciale (Ref. 216) NOS/NIB Vintage Off-White Cloth Handlebar Tape

£19.00 £20.00

✓ Original bar tape - in production from the 1960s to the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Guidoplast Tresse Speciale bar tape (or grip, or wrap if you prefer), hailing from France and in production from the 1960s to the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!

OVERVIEW

Condition - New Old Stock - In Original Packaging*
Model ID - Ref. 216
Production Era - 1960s - 1980s
Country - French
Stock Code - D-BT18V

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Colour* - Off-White
Tape Style - Cloth (Cotton)

*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Heta Gran Carrera Milremo NOS Vintage Black 44 - 48.5 cm Frame Fit Bike Pump

£23.75 £25.00

✓ Original pump - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Heta Gran Carrera bicycle pump, hailing from Spain and in production during the 1970s (yet still new & unused after all this time!). An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!

OVERVIEW

Condition - New Old Stock*
Production Era - 1970s
Country - Spanish
Material - Plastic
Weight - 133 g
Stock Code - D-PM-F45V

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Colour* - Black
Valve Type - Presta
Pump Mount Type - Frame Fit
Mount Location** - Seat Tube
Length (Min-Max) - 44 - 48.5 cm

*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.

**See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.

Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.

Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!

Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.

View full product details

Heta Gran Carrera Milremo NOS Vintage Black 45.5 - 50 cm Frame Fit Bike Pump

£23.75 £25.00

✓ Original pump - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Heta Gran Carrera bicycle pump, hailing from Spain and in production during the 1970s (yet still new & unused after all this time!). An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!

OVERVIEW

Condition - New Old Stock*
Condition Notes - Some scratches to the main body
Production Era - 1970s
Country - Spanish
Material - Plastic
Weight - 137 g
Stock Code - D-PM-F46V

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Colour* - Black
Valve Type - Presta
Pump Mount Type - Frame Fit
Mount Location** - Seat Tube
Length (Min-Max) - 45.5 - 50 cm

*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.

**See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.

Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.

Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!

Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.

View full product details

Heta Gran Carrera Milremo NOS Vintage Black 50 - 54.5 cm Frame Fit Bike Pump

£23.75 £25.00

✓ Original pump - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Heta Gran Carrera bicycle pump, hailing from Spain and in production during the 1970s (yet still new & unused after all this time!). An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!

OVERVIEW

Condition - New Old Stock*
Production Era - 1970s
Country - Spanish
Material - Plastic
Weight - 140 g
Stock Code - D-PM-F34V

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Colour* - Black
Valve Type - Presta
Pump Mount Type - Frame Fit
Mount Location** - Seat Tube
Length (Min-Max) - 50 - 54.5 cm

*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.

**See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.

Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.

Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!

Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.

View full product details

Heta Mascot Milremo Vintage Black 46 - 50 cm Frame Fit Bike Pump

£19.00 £20.00

✓ Original pump - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & tested
✓ Worldwide shipping

Heta Mascot bicycle pump, hailing from Spain and in production during the 1970s. An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!

The pump's been thoroughly checked, tested and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Condition - Very Good
Production Era - 1970s
Country - Spanish
Material - Plastic
Weight - 136 g
Stock Code - U-PM-F1V

TECHNICAL INFO

Colour* - Black
Valve Type - Presta
Pump Mount Type - Frame Fit (With Peg Hole at Handle End)
Mount Location** - Seat Tube
Length (Min-Max) - 46 - 50 cm

*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.

**See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.

Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.

Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!

Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.

View full product details

Heta Sport Vintage White 50 - 55 cm Frame Fit Bike Pump

£23.75 £25.00

✓ Original pump - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & tested
✓ Worldwide shipping

Heta Sport bicycle pump, hailing from Spain and in production from the 1970s to the 1980s. An excellent choice for vintage cycling enthusiasts, but great for cyclists of the non-vintage variety too!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong pump!

The pump's been thoroughly checked, tested and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Condition - Good
Production Era - 1970s & 1980s
Country - Spanish
Material - Plastic
Weight - 151 g
Stock Code - U-PM-F2V

TECHNICAL INFO

Colour* - White
Valve Type - Presta
Pump Mount Type - Frame Fit (With Peg Hole at Handle End)
Mount Location** - Seat Tube
Length (Min-Max) - 50 - 55 cm

*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.

**See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Valve Type - there are 3 types of valves; Presta are thin with a little knurled nut on the end, Schrader are wider (the same as you would find on a car), and the less common Woods (aka "Dunlop"). Pumps designed for Presta valves can be used on Woods valves. Some pumps use hose connectors, these are available for all valve types.

Pump Mount Type - 'peg fit' pumps require pump pegs or 'umbrella' clips to fit to the frame, 'frame fit 'pumps are designed with curved ends to mount between two tubes (although these often have holes for pegs too). If mounting directly you'll need the correct length to fit your frame, or a clip/peg to hold one end.

Mount Location - frame fit pumps usually mount to the seat tube with the ends compressed between the top and down tube, they can however be mounted on other tubes as long as there's something supporting the handle end. Some head tubes have a little nipple or a small enough gap for under top tube mounting (this can be replcated with a simple strap or cable tie), and of course pump pegs or clips can be fitted anywhere!

Length (Min-Max) - the length of the pump fully compressed and uncompressed, measured at the points of support. The space you to intend to mount the pump should be within 1 cm of the minimum or maximum length to allow the pump to be securely mounted and dismounted.

View full product details

HL Corp (Zoom) Black NOS Classic 120 mm 1 1/8" Quill Stem

£20.00

✓ Original part - produced in the 2000s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

HL Corp (Zoom) handlebar stem (or gooseneck if you prefer), hailing from China and in production during the 2000s. Made from steel and weighing in at 484 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

Condition - New Old Stock*
Production Era - 2000s
Country - Chinese
Material - Steel
Weight - 484 g
Stock Code - D-G1-ST231C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length (ctc)* - 120 mm
Quill Size - 1 1/8"
Steerer Size (ID) - 25.4 mm (Standard 1 1/8")
Total Shaft Height - 155 mm
Clamp Size - 25.4 mm

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼SAFETY & COMPLIANCE

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are strongly recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - HL Corp (Shenzen), The 3rd Industrial Park, Bitou Village, Song Gang Town, Baoan District, Shenzhen, 518105 China

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

View full product details

HTI P38 Vintage MTB Pedals

£20.00

✓ Original pedals - produced in the 1980s
✓ Professionally checked & cleaned
✓ Worldwide shipping

HTI P38 pedals (or peddles if you prefer), hailing from Taiwan and in production during the 1980s. Made from steel/plastic and weighing in at 409 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

The pedals have been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Body Condition - Good
Bearing/Race Condition - OK
Model ID - P38
Production Era - 1980s
Country - Taiwanese
Material - Steel / Plastic
Weight - 409 g
Stock Code - U-PD100V

TECHNICAL INFO

Pedal Type - MTB
Pedal Threads - Standard (9/16" x 20 TPI)

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Pedal Type - this is just a guide to give you an idea of the pedal type, but any pedal can technically be used for any purpose. Track pedals are designed without the pointed 'quill' for safety though, so it's best to only use track pedals for this purpose. Most track pedals, along with quill & aero road pedals are designed to be used with toe clips & straps for best performance.

Pedal Threads - this must match the thread on your cranks. Sometimes it's stamped on the end of the crank arm, but most bikes use a standard thread of 9/16” x 20 tpi. The exceptions being older French bikes, bikes with cheaper one-piece type chainsets and Shimano’s Dyna Drive system (easily identifiable as the pedal holes are about an inch wide!).

View full product details

Iscaselle Dainy NOS/NIB Vintage Red Vinyl Handlebar Tape

£19.00 £20.00

✓ Original bar tape - produced in the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Iscaselle Dainy bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!

OVERVIEW

Condition - New Old Stock - In Original Packaging*
Production Era - 1980s
Country - Italian
Stock Code - D-BT3V

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Colour* - Red
Tape Style - Vinyl (PVC Perforated)

*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Iscaselle Design Lady NOS Classic Black Saddle

£21.25 £25.00

✓ Original saddle - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Iscaselle Design Lady saddle, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from synthetic/steel and weighing in at 277 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s
Country - Italian
Material - Synthetic/Steel
Weight - 277 g
Stock Code- D-SA85C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Colour* - Black
Cover Material - Synthetic
Length - 250 mm
Width - 175 mm

*The colour description is just a guide, please check the photos to get a good idea of the colour too, as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Iscaselle NOS/NIB Vintage Neon Yellow Vinyl Handlebar Tape

£14.25 £15.00

✓ Original bar tape - produced in the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Iscaselle bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!

If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!

OVERVIEW

Condition - New Old Stock - In Original Packaging*
Production Era - 1980s
Country - Italian
Stock Code - D-BT50V

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Colour* - Neon Yellow
Tape Style - Vinyl (PVC Non-Perforated)

*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Italmanubri (ITM) NOS Classic 120 mm 1 1/8" Quill Stem

£19.00 £20.00

✓ Original part - in production from the 1990s to the 2000s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Italmanubri (ITM) stem, hailing from Italy and in production from the 1990s to the 2000s (yet still new & unused after all this time!). Made from steel and weighing in at 424 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s & 2000s
Country - Italian
Material - Steel
Weight - 424 g
Stock Code - D-ST167C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length (ctc)* - 120 mm
Quill Size - 1 1/8"
Steerer Size (ID) - 25.4 mm (Standard 1 1/8")
Total Shaft Height - 160 mm
Clamp Size - 26.0 mm

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

View full product details

Jaftex NOS Nylon Vintage Black Pedal / Toe Clip Straps

£22.50

✓ Original toe straps - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Jaftex toe straps, hailing from France and in production from the 1970s to the 1980s (yet still new & unused after all this time!). The straps are black in colour and made from nylon/steel, the perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!

If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe straps!

OVERVIEW

Condition - New Old Stock*
Production Era - 1970s & 1980s
Country - French
Material - Nylon / Steel
Weight - 50 g
Stock Code - D-STR28V

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Colour* - Black
Toe Strap Type - Standard
Strap Width - 12 mm
Toe Strap Length - 41 cm

*The colour description is just a guide, please check the photos to get a good idea of the colour too, as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.

Strap Width - measured across one of the straps at its widest point.

Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.

View full product details

Jelly Belly NOS Classic Cycling Cotton Cap

£20.00

✓ Original classic cap - 2000s style!
✓ New old stock! Still unused after all these years
✓ Great alternative to buying new
✓ Worldwide shipping

Classic Jelly Belly cycling cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!

OVERVIEW

Cap Size** - One Size (Standard Fit)
Condition - New Old Stock*
Production Era - 2000s
Stock Code - D-CAP48C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

**Most cycling caps come in ‘one size’ as standard and will fit most head sizes. Some can be on the small side however, so we list these as a ‘smaller fit’ and wouldn’t recommend them for a head circumference above 58 cm.

DETAIL

Cap Type - Summer/Under Helmet
Construction - 4 Panel
Colour* - Green / White

*The colour description is just a guide, please check the photos to get a good idea of the colour too, as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.

Construction - the number of panels the cap body is made up of, not including the peak.

View full product details

JFM Blue & White Squiggles Small Vintage Sleeveless Cycling Jersey

£12.75 £15.00

✓ Original vintage jersey - 1980s style!
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & honestly graded
✓ Great alternative to buying new
✓ Worldwide shipping

JFM sleeveless cycling jersey, hailing from France and likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike, and also a responsible alternative to buying brand new cycling kit!

If you're taking part in L'Eroica or a similar vintage event, this is compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong jersey!

The jersey’s been thoroughly checked over and graded as OK condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.

OVERVIEW

Size Estimate (Chest)** - Small (34-37" Chest)
Condition - OK
Condition Notes - Some abrasion marks and the zipper is a little stiff
Material - Synthetic
Stock Code - U-JS61V

**This is just an estimate so please check the actual measurements before buying, the best way to get the right fit is to compare them with those of a garment that fits well.

DETAIL & SIZING

Sleeve Type - Sleeveless
Pit to Pit (Laid Flat) - 47 cm
Top to Bottom (Front) - 64 cm
Top to Bottom (Back) - 73 cm
Across Neck (Laid Flat) - 21 cm

NB: Check the help section to see how we take these measurements to get a good comparison.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

We've also provided photographs below to illustrate how we take our measurements.

Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.

Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.

Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.

Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).

Across Sleeve End - measured across the sleeve end, laid flat.

View full product details

Kalin Black NOS Classic 45 mm 1" Quill Stem

£19.00 £20.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 278 grams
✓ Worldwide shipping

Kalin stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 278 grams - pretty lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s
Country - Taiwanese
Material - Aluminium
Weight - 278 g
Stock Code - D-ST177C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length (ctc)* - 45 mm
Quill Size - 1"
Steerer Size (ID) - 22.2 mm (Standard)
Total Shaft Height - 155 mm
Clamp Size - 25.4 mm

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

◄HELP SECTION

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

View full product details

Kalin Bullet Nose NOS Classic 25.4 mm Seatpost

£19.00 £20.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 153 grams!
✓ Worldwide shipping

Kalin seatpost, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 153 grams - incredibly lightweight for seatposts at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s
Country - Taiwanese
Material - Aluminium
Weight - 153 g
Stock Code- D-SP50C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Seatpost Diameter - 25.4 mm
Length (Centre of Rails to Base) - 300 mm

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Kalin High Rise NOS Classic 110 mm 1" Quill Stem

£20.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kalin stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from steel and weighing in at 441 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s
Country - Taiwanese
Material - Steel
Weight - 441 g
Stock Code - D-ST176C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length (ctc)* - 110 mm
Quill Size - 1"
Steerer Size (ID) - 22.2 mm (Standard)
Total Shaft Height - 150 mm
Clamp Size - 25.4 mm

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

View full product details

Kalloy Classic 30.2 mm Seatpost

£9.00 £10.00

✓ Original part - produced in the 1990s
✓ Professionally checked & cleaned
✓ Worldwide shipping

Kalloy seatpost, hailing from Taiwan and in production during the 1990s. Made from aluminium and weighing in at 366 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

The seatpost's been carefully cleaned, thoroughly checked by one of our mechanics and graded as poor condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Condition - Poor
Production Era - 1990s
Country - Taiwanese
Material - Aluminium
Weight - 366 g
Stock Code - U-SP107C

TECHNICAL INFO

Seatpost Diameter - 30.2 mm
Length (Centre of Rails to Base) - 300 mm

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom., otherwise you’ll need to measure with a caliper or seatpost sizing tool as seatpost diameters go up in 0.2 mm increments.

Length (Centre of Rails to Base) - measured from where the centre of the saddle rails will sit once installed, all the way to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.

View full product details

Kalloy Fluted Bullet Nose NOS Classic 26.4 mm Seatpost

£23.75 £25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 91 grams!
✓ Worldwide shipping

Kalloy seatpost, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 91 grams - incredibly lightweight for seatposts at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s
Country - Taiwanese
Material - Aluminium
Weight - 91 g
Stock Code- D-SP51C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Seatpost Diameter - 26.4 mm
Length (Centre of Rails to Base) - 190 mm

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Kalloy Fluted NOS Vintage 26.8 mm Bullet Nose Seatpost

£19.00 £20.00

✓ Original part - in production from the 1980s to the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kalloy bullet nose (or candlestick if you prefer) seatpost, hailing from Taiwan and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 88 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

Please note: Once inserted into a frame this cannot be returned, so please make sure to double check the diameter is correct before installing.

OVERVIEW

Condition - New Old Stock*
Production Era - 1980s & 1990s
Country - Taiwanese
Material - Aluminium
Weight - 88 g
Stock Code - D-SPB10V

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Seatpost Diameter - 26.8 mm
Length (Top to Bottom) - 190 mm

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom, if not you’ll need to measure with a caliper or seatpost sizing tool as the sizes go up in 0.2 mm increments.

Length (Top to Bottom) - measured from the top to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.

View full product details

Kalloy KL100 Silver Classic 100 mm 1" Quill Stem

£20.00

✓ Original part - in production from the 1990s to the 2000s
✓ Checked & cleaned
✓ Worldwide shipping

Kalloy KL100 handlebar stem (or gooseneck if you prefer), hailing from Taiwan and in production from the 1990s to the 2000s. Made from aluminium/steel and weighing in at 349 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

The stem's been carefully cleaned, thoroughly checked and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Condition - Excellent
Production Era - 1990s & 2000s
Country - Taiwanese
Material - Aluminium / Steel
Weight - 349 g
Stock Code - U-G1-ST238C

TECHNICAL INFO

Extension Length (ctc)* - 100 mm
Quill Size - 1"
Steerer Size (ID) - 22.2 mm (Standard)
Total Shaft Height - 150 mm
Clamp Size - 25.4 mm

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼SAFETY & COMPLIANCE

This product complies with the EU General Product Safety Regulation (GPSR). Professional installation and regular inspections are strongly recommended. Due to the product's age, extra care should be taken during use.

Product Manufacturer - Kalloy Uno, No.186, Dazhou Rd., Shengang Dist., Taichung City 429, Taiwan

EU Authorised Representative - Global Trade Department NI Ltd, Office 834, Unit 6, 100 Lisburn Road, Belfast BT9 6AG, Northern Ireland

▼HELP SECTION

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

View full product details

Kalloy KL80 Silver NOS Classic 80 mm 1" Quill Stem

£23.75 £25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kalloy KL80 stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 307 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

Condition - New Old Stock*
Model ID - KL80
Production Era - 1990s
Country - Taiwanese
Material - Aluminium / Steel
Weight - 307 g
Stock Code - D-ST180C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length (ctc)* - 80 mm
Quill Size - 1"
Steerer Size (ID) - 22.2 mm (Standard)
Total Shaft Height - 150 mm
Clamp Size - 25.4 mm

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

View full product details

Kalloy Red NOS Classic 110 mm 1 1/8" A-Head Stem

£19.00 £20.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kalloy ahead handlebar stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 182 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s
Country - Taiwanese
Material - Aluminium
Weight - 182 g
Stock Code - D-STA12C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length (ctc)* - 110 mm
Steerer Size (OD) - 1 1/8" (28.6 mm)
Bar Clamp Size - 25.4 mm
Stack Height - 42 mm
Angle - 97 Degrees

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

View full product details

Kalloy Red Vintage 95 mm 1" Quill Stem

£20.00

✓ Original part - produced in the 1980s
✓ Checked & cleaned
✓ Worldwide shipping

Kalloy handlebar stem (or gooseneck if you prefer), hailing from Taiwan and in production during the 1980s. Made from aluminium/steel and weighing in at 324 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

The stem's been carefully cleaned, thoroughly checked and graded as OK condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Condition - OK
Production Era - 1980s
Country - Taiwanese
Material - Aluminium / Steel
Weight - 324 g
Stock Code - U-ST221V

TECHNICAL INFO

Extension Length (ctc)* - 95 mm
Quill Size - 1"
Steerer Size (ID) - 22.2 mm (Standard)
Total Shaft Height - 125 mm
Clamp Size - 26.0 mm
Rise - 35 Degrees

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

View full product details

Kalloy Uno NOS Classic 31.6 mm Seatpost

£23.75

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 286 grams
✓ Worldwide shipping

Kalloy Uno seatpost, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 286 grams - pretty lightweight for seatposts at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

Please note: Once inserted into a frame this cannot be returned, so please make sure to double check the diameter is correct before installing.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s
Country - Taiwanese
Material - Aluminium / Steel
Weight - 286 g
Stock Code - D-SP183C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Seatpost Diameter - 31.6 mm
Length (Centre of Rails to Base) - 345 mm

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Seatpost Diameter - this needs to match the internal diameter of your frame’s seat tube closely, it should be possible to insert the seatpost without force but the fit should be tight enough so it doesn’t just drop in, with no play once inserted. If you have a post that fits the measurement should be stamped somewhere near the bottom, if not you’ll need to measure with a caliper or seatpost sizing tool as the sizes go up in 0.2 mm increments.

Length (Centre of Rails to Base) - measured from where the centre of the saddle rails will sit once installed, all the way to the bottom of the seatpost. Normally there’s a mark to tell you how much of the seatpost needs to be inserted in the frame, however this isn’t always the case so we’d recommend allowing a minimum of 6 cm.

View full product details

Kalloy Uno Silver NOS Classic 130 mm 1 1/8" Quill Stem

£23.75 £25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 237 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 237 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s
Country - Taiwanese
Material - Aluminium
Weight - 237 g
Stock Code - D-ST212C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length (ctc)* - 130 mm
Quill Size - 1 1/8"
Steerer Size (ID) - 25.4 mm (Standard 1 1/8")
Total Shaft Height - 130 mm
Clamp Size - 25.4 mm
Rise - 90 Degrees

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

View full product details

Kalloy Uno Silver NOS Classic 130 mm 1 1/8" Quill Stem

£23.75 £25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 237 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 237 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s
Country - Taiwanese
Material - Aluminium
Weight - 237 g
Stock Code - D-ST212C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length (ctc)* - 130 mm
Quill Size - 1 1/8"
Steerer Size (ID) - 25.4 mm (Standard 1 1/8")
Total Shaft Height - 130 mm
Clamp Size - 25.4 mm
Rise - 90 Degrees

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

View full product details

Kas Cycling Cap

£12.50

SIZING & MATERIAL:

Size:

One Size Fits All

SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, normally within 2-3 days, but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Kinlin T10 Retro 36h 27" Clincher Rim

£20.00 £25.00

✓ Professionally checked & cleaned
✓ Timeless design - for original or retro styled bikes
✓ Worldwide shipping

The rim's been carefully cleaned, thoroughly checked by one of our mechanics and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Condition - Excellent
Material - Aluminium
Weight - 500 grams
Stock Code - U-RS52R

TECHNICAL INFO

Drilling - 36 Hole
Rim Size - 27" Clincher
ISO Diameter - 630 mm
Valve Type - Schraeder
Rim Width (OD) - 25 mm
Rim Height - 14 mm

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Kroon-Hypro Vintage Dutch Cotton Cycling Cap

£23.75

✓ Original vintage cap - 1980s style!
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & honestly graded
✓ Great alternative to buying new
✓ Worldwide shipping

Vintage Kroon-Hypro cycling cap, hailing from The Netherlands and likely made in the 1980s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!

If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cap!

The cap's been thoroughly checked over and graded as very good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.

OVERVIEW

Cap Size** - One Size (Standard Fit)
Condition - Very Good
Production Era - 1980s
Country - Dutch
Stock Code - U-CAP6V

**Most cycling caps come in ‘one size’ as standard and will fit most head sizes. Some can be on the small side however, so we list these as a ‘smaller fit’ and wouldn’t recommend them for a head circumference above 58 cm.

DETAIL

Cap Type - Summer/Under Helmet
Construction - 4 Panel
Colour* - Black / Yellow

*The colour description is just a guide, please check the photos to get a good idea of the colour too, as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.

Construction - the number of panels the cap body is made up of, not including the peak.

View full product details

KS Vintage Short Sleeve Cycling Jersey

£15.00

Measurements are taken when laid flat and the length is measured down the back from the bottom of the collar to the bottom of the hem.

NB: We've given a 'snug but comfortable' estimated size as a guide only. Due to the nature of vintage items, it's always best to refer to the actual measurements given, and if possible compare them to another jersey that fits well.

SIZING& CONDITION:

Estimated Size:	Medium
Pit to Pit:	21" / 53cm
Length:	29.5" / 75cm
Material:	100% Polyester
Condition:	Good/OK

SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, normally within 2-3 days, but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Lampre - Fondital NOS Classic Cycling Cotton Cap

£18.75

✓ Original classic cap - 2000s style!
✓ New old stock! Still unused after all these years
✓ Great alternative to buying new
✓ Worldwide shipping

Classic Lampre - Fondital cycling cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!

OVERVIEW

Cap Size** - One Size (Standard Fit)
Condition - New Old Stock*
Production Era - 2000s
Stock Code - D-CAP49C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

**Most cycling caps come in ‘one size’ as standard and will fit most head sizes. Some can be on the small side however, so we list these as a ‘smaller fit’ and wouldn’t recommend them for a head circumference above 58 cm.

DETAIL

Cap Type - Summer/Under Helmet
Construction - 4 Panel
Colour* - Blue / Pink

*The colour description is just a guide, please check the photos to get a good idea of the colour too, as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.

Construction - the number of panels the cap body is made up of, not including the peak.

View full product details

Lampre - NGC NOS Classic Cotton Cycling Cap

£20.00

✓ Original classic cap - 2000s style!
✓ New old stock! Still unused after all these years
✓ Great alternative to buying new
✓ Worldwide shipping

Classic Lampre - NGC cycling cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!

OVERVIEW

Cap Size** - One Size (Standard Fit)
Condition - New Old Stock*
Production Era - 2000s
Stock Code - D-CAP52C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

**Most cycling caps come in ‘one size’ as standard and will fit most head sizes. Some can be on the small side however, so we list these as a ‘smaller fit’ and wouldn’t recommend them for a head circumference above 58 cm.

DETAIL

Cap Type - Summer/Under Helmet
Construction - 4 Panel
Colour* - White / Pink / Blue

*The colour description is just a guide, please check the photos to get a good idea of the colour too, as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.

Construction - the number of panels the cap body is made up of, not including the peak.

View full product details

Lapize 160 Size M Vintage Steel Toe Clips

£14.25 £15.00

✓ Original toe clips - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Lapize 160 toe clips (or pedal cages if you prefer), hailing from France and in production during the 1980s. Made from steel and weighing in at 47 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!

The toe clips have been checked, cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.

OVERVIEW

Size Guide** - M (Up to EU 42)
Condition - Very Good
Production Era - 1980s
Material - Steel
Weight - 47 g
Stock Code - U-TC86V

**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.

TECHNICAL INFO

Pedal Fixing - Standard (Quill / Platform)
Toe Strap Fit - Single Strap
Length (Fixing End to Toe End)* - 5.5 cm
Distance Between Fixing Bolts (ctc) - 25 mm

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.

Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.

Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.

Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).

View full product details

Lapize 160 Size M Vintage Steel Toe Clips / Cages

£9.00 £10.00

✓ Original toe clips - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Lapize 160 toe clips, hailing from France and in production during the 1980s. Made from steel and weighing in at 48 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!

The toe clips have been cleaned, checked by one of our mechanics and graded as OK condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.

OVERVIEW

Size Guide** - M (Up to EU 42)
Condition - OK
Production Era - 1980s
Material - Steel
Weight - 48 g
Stock Code - U-TC10V

**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.

TECHNICAL INFO

Toe Clip Size - M
Pedal Fixing - Standard (Quill / Platform)
Toe Strap Type - Single Strap
Length (Fixing End to Toe End)* - 5.5 cm
Distance Between Fixing Bolts (ctc) - 25 mm

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.

Toe Strap Type - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.

Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.

Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).

View full product details

Lapize 511 Poutrait-Morin Leather Vintage White Toe Clip Straps

£17.50

✓ Original toe straps - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

Lapize 511 toe straps (or pedal straps if you prefer), hailing from France and in production during the 1980s. The straps are white in colour and made from leather/steel, the perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!

If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe straps!

The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Condition - Good
Production Era - 1980s
Country - French
Material - Leather / Steel
Weight - 48 g
Stock Code - U-STR46V

TECHNICAL INFO

Colour* - White
Toe Strap Type - Standard
Strap Width - 12 mm
Toe Strap Length - 41 cm

*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.

Strap Width - measured across one of the straps at its widest point.

Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.

View full product details

Le Tour Large Flange Vintage 32h Front Hub

£22.50 £25.00

✓ Original hub - produced in the 1970s
✓ Super lightweight for the era - only 169 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked, cleaned & serviced
✓ Worldwide shipping

Le Tour front hub, hailing from France and in production during the 1970s. Made from aluminium/steel and weighing in at 169 grams - incredibly lightweight for a front hub at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong hub!

The hub's been carefully cleaned, thoroughly serviced by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Body Condition - Good
Bearing / Race Condition - Good
Production Era - 1970s
Country - French
Material - Aluminium / Steel
Weight - 169 g
Stock Code - U-HU-F31V

TECHNICAL INFO

Spoke Drilling - 32 Hole
Spacing (O.L.D.) - 100 mm

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Spoke Drilling - the number of holes for the spokes, your wheel rim needs to match the hub exactly.

Spacing (O.L.D.) - the width of the hub measured at its widest point, from the outside of the locking end nuts (O.L.D. = Over Locknut Dimension), not including the hub axle. This measurement needs to match the inside of your fork's dropouts. Steel forks can be stretched or squeezed a few mm but it's always best to avoid this if possible, aluminium or carbon forks should never be stretched.

View full product details

Look Arc Classic Clipless Pedals

£18.75 £25.00

These classic Look Arc pedals were produced in the 1990s and weigh in at 449 grams for the pair. They're clipless pedals designed to fit cranks with standard (9/16" x 20 tpi) pedal threads.

The pedals have been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as these are vintage parts, even new old stock pedals may show signs of age from storage over the years (you can enlarge or zoom into the photos).

TECHNICAL INFO & CONDITION

Pedal Type - Clipless
Pedal Threading - Standard (9/16" x 20 tpi)
Body Condition - OK
Bearing/Race Condition - Excellent
Weight - 449 grams
Era - 1990s
Country - French

SHIPPING, TAXES & RETURNS

We can ship these Look pedals anywhere in the world, there's a shipping calculator on the cart page so you can see the cost of postage before buying. Your order will be carefully packed & sent with tracking & insurance, normally within 2-3 days, but larger items can take an extra day or 2 to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

LOOK Classic Quick Release Rear Skewer

£15.75 £17.50

✓ Original skewer - produced in the 1990s
✓ Checked & cleaned
✓ Worldwide shipping

LOOK rear skewer, hailing from France and in production during the 1990s. Made from steel/aluminium and weighing in at 80 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

The skewer's been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Condition - Good
Production Era - 1990s
Country - French
Material - Steel/Aluminium
Weight - 80 g
Stock Code - U-SKW-R7C

TECHNICAL INFO

Skewer Type - Quick Release
Spacing* - 140 mm
Threaded Section - 29 mm / 23 mm
End Nut Length - 14 mm

*See help section.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Skewer type - quick release skewers allow you to remove the wheel without any tools, whereas allen key and security skewers require a tool to allow the wheel to be removed.

*Spacing - this should be within a few milimetres of your frame's outer dropout spacing (measured from the outside where the skewers clamp down). The measurement provided was taken with the exiting hole of the end nut flush with the end of the skewer. There will be some wiggle room to allow a narrower or wider dropout spacing to fit, we've provided the threaded section and end nut measurements to give you an indication of how much.

Threaded section - the amount of thread on the skewers for the end nut to be threaded onto.

End nut length - the total length of the nut from end to end.

View full product details

Look PP76 Classic Clipless Pedals

£18.75 £25.00

These classic Look PP76 pedals were produced in the 1990s and weigh in at 447 grams for the pair. They're clipless pedals designed to fit cranks with standard (9/16" x 20 tpi) pedal threads.

The pedals have been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as these are vintage parts, even new old stock pedals may show signs of age from storage over the years (you can enlarge or zoom into the photos).

TECHNICAL INFO & CONDITION

Pedal Type - Clipless
Pedal Threading - Standard (9/16" x 20 tpi)
Body Condition - OK
Bearing/Race Condition - Excellent
Weight - 447 grams
Era - 1990s
Country - French

SHIPPING, TAXES & RETURNS

We can ship these Look pedals anywhere in the world, there's a shipping calculator on the cart page so you can see the cost of postage before buying. Your order will be carefully packed & sent with tracking & insurance, normally within 2-3 days, but larger items can take an extra day or 2 to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Look PP76 Classic Clipless Pedals

£18.75 £25.00

These classic Look PP76 pedals were produced in the 1990s and weigh in at 438 grams for the pair. They're clipless pedals designed to fit cranks with standard (9/16" x 20 tpi) pedal threads.

The pedals have been professionally checked, cleaned & carefully photographed to show the cosmetic condition. Please ensure to take a close look as these are vintage parts, even new old stock pedals may show signs of age from storage over the years (you can enlarge or zoom into the photos).

TECHNICAL INFO & CONDITION

Pedal Type - Clipless
Pedal Threading - Standard (9/16" x 20 tpi)
Body Condition - OK
Bearing/Race Condition - Excellent
Weight - 438 grams
Era - 1990s
Country - French

SHIPPING, TAXES & RETURNS

We can ship these Look pedals anywhere in the world, there's a shipping calculator on the cart page so you can see the cost of postage before buying. Your order will be carefully packed & sent with tracking & insurance, normally within 2-3 days, but larger items can take an extra day or 2 to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

LOOK PP76 Carbon Vintage Clipless Pedals

£24.00 £30.00

✓ Original pedals - in production from the 1980s to the 1990s
✓ Professionally checked & cleaned
✓ Worldwide shipping

LOOK PP76 Carbon pedals, hailing from France and in production from the 1980s to the 1990s. Made from aluminium/steel and weighing in at 449 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

The pedals have been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.

OVERVIEW

Body Condition - Good
Bearing/Race Condition - Very Good
Condition Notes - Small amount of play in left hand pedal
Production Era - 1980s & 1990s
Country - French
Material - Aluminium/Steel
Weight - 449 g
Stock Code- U-PD-C4V

TECHNICAL INFO

Compatible Cleats - Look Delta
Pedal Threads - Standard (9/16" x 20 TPI)

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

View full product details

Lotto - Mobistar NOS Classic Cotton Cycling Cap

£20.00

✓ Original classic cap - 1990s style!
✓ New old stock! Still unused after all these years
✓ Great alternative to buying new
✓ Worldwide shipping

Classic Lotto - Mobistar cycling cap, likely made in the 1990s given the style (yet still new & unused after all this time!). An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!

OVERVIEW

Cap Size** - One Size (Standard Fit)
Condition - New Old Stock*
Production Era - 1990s
Stock Code - D-CAP59C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

**Most cycling caps come in ‘one size’ as standard and will fit most head sizes. Some can be on the small side however, so we list these as a ‘smaller fit’ and wouldn’t recommend them for a head circumference above 58 cm.

DETAIL

Cap Type - Summer/Under Helmet
Construction - 4 Panel
Colour* - Black / Red / Green

*The colour description is just a guide, please check the photos to get a good idea of the colour too, as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.

Construction - the number of panels the cap body is made up of, not including the peak.

View full product details

Lotto - Predictor NOS Classic Cotton Cycling Cap

£20.00

✓ Original classic cap - 2000s style!
✓ New old stock! Still unused after all these years
✓ Great alternative to buying new
✓ Worldwide shipping

Classic Lotto - Predictor cycling cap, likely made in the 2000s given the style. An excellent choice for wearing on your classic bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!

OVERVIEW

Cap Size** - One Size (Standard Fit)
Condition - New Old Stock*
Production Era - 2000s
Stock Code - D-CAP53C

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

**Most cycling caps come in ‘one size’ as standard and will fit most head sizes. Some can be on the small side however, so we list these as a ‘smaller fit’ and wouldn’t recommend them for a head circumference above 58 cm.

DETAIL

Cap Type - Summer/Under Helmet
Construction - 4 Panel
Colour* - Pink / Grey

*The colour description is just a guide, please check the photos to get a good idea of the colour too, as we make sure these are as close to the true colour as possible.

▼SHIPPING, TAXES & RETURNS

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

EU Customers – for orders under €150 (excluding shipping), VAT will be collected at checkout – no extra import fees to pay on delivery! For orders over €150 any import fees will be payable to the carrier before delivery.

USA Customers – import fees are now collected at checkout for all orders to the US, so there won’t be any surprise charges when your order arrives.

Other International Customers – local import fees may still apply, charged by your customs office or courier before delivery. These are not collected by us, so please check your local rates before purchasing.

Any applicable fees will appear at checkout.

▼HELP SECTION

Cap Type - we refer to the classic cycling cap type as summer/under helmet, although they can of course be used all year round. When worn under a helmet they provide comfort, sun protection and are sweat-wicking too. Winter hats will usually cover the ears and are referred to as 'Belgian' caps. Baseball caps were often worn by support teams or sold as branded merchandise.

Construction - the number of panels the cap body is made up of, not including the peak.

View full product details

Under £25

Refine

Product Type

Gender/Age

Era

Speed

Size

Price

Brand

Colour

Follow

Under £25

Refine

Product Type

Gender/Age

Era

Speed

Size

Price

Brand

Colour

Gonso Short Sleeve Vintage Cycling Jersey

Gonso Short Sleeve Vintage Cycling Jersey

Gonso Tour De Landle 99 Short Sleeve Vintage Cycling Jersey

Gonso Vintage Cycling Jersey

Gran Premio Leather Vintage Black Pedal / Toe Clip Straps

✓ Original toe straps - in production from the 1970s to the 1980s✓ Suitable for historic cycling events such as L'Eroica✓ Checked & cleaned✓ Worldwide shipping

Guidoplast Tresse Speciale (Ref. 216) NOS/NIB Vintage Off-White Cloth Handlebar Tape

✓ Original bar tape - in production from the 1960s to the 1980s✓ New old stock & still in the original packaging!✓ Suitable for historic cycling events such as L'Eroica✓ Worldwide shipping

Heta Gran Carrera Milremo NOS Vintage Black 44 - 48.5 cm Frame Fit Bike Pump

✓ Original pump - produced in the 1970s✓ New old stock! Still unused after all these years✓ Suitable for historic cycling events such as L'Eroica✓ Worldwide shipping

Heta Gran Carrera Milremo NOS Vintage Black 45.5 - 50 cm Frame Fit Bike Pump

✓ Original pump - produced in the 1970s✓ New old stock! Still unused after all these years✓ Suitable for historic cycling events such as L'Eroica✓ Worldwide shipping

Heta Gran Carrera Milremo NOS Vintage Black 50 - 54.5 cm Frame Fit Bike Pump

✓ Original pump - produced in the 1970s✓ New old stock! Still unused after all these years✓ Suitable for historic cycling events such as L'Eroica✓ Worldwide shipping

Heta Mascot Milremo Vintage Black 46 - 50 cm Frame Fit Bike Pump

✓ Original pump - produced in the 1970s✓ Suitable for historic cycling events such as L'Eroica✓ Checked & tested✓ Worldwide shipping

Heta Sport Vintage White 50 - 55 cm Frame Fit Bike Pump

✓ Original pump - in production from the 1970s to the 1980s✓ Suitable for historic cycling events such as L'Eroica✓ Checked & tested✓ Worldwide shipping

HL Corp (Zoom) Black NOS Classic 120 mm 1 1/8" Quill Stem

✓ Original part - produced in the 2000s✓ New old stock! Still unused after all these years✓ Worldwide shipping

HTI P38 Vintage MTB Pedals

✓ Original pedals - produced in the 1980s✓ Professionally checked & cleaned✓ Worldwide shipping

Iscaselle Dainy NOS/NIB Vintage Red Vinyl Handlebar Tape

✓ Original bar tape - produced in the 1980s✓ New old stock & still in the original packaging!✓ Suitable for historic cycling events such as L'Eroica✓ Worldwide shipping

Iscaselle Design Lady NOS Classic Black Saddle

✓ Original saddle - produced in the 1990s✓ New old stock! Still unused after all these years✓ Worldwide shipping

Iscaselle NOS/NIB Vintage Neon Yellow Vinyl Handlebar Tape

✓ Original bar tape - produced in the 1980s✓ New old stock & still in the original packaging!✓ Suitable for historic cycling events such as L'Eroica✓ Worldwide shipping

Italmanubri (ITM) NOS Classic 120 mm 1 1/8" Quill Stem

✓ Original part - in production from the 1990s to the 2000s✓ New old stock! Still unused after all these years✓ Worldwide shipping

Jaftex NOS Nylon Vintage Black Pedal / Toe Clip Straps

✓ Original toe straps - in production from the 1970s to the 1980s✓ New old stock! Still unused after all these years✓ Suitable for historic cycling events such as L'Eroica✓ Worldwide shipping

Jelly Belly NOS Classic Cycling Cotton Cap

✓ Original classic cap - 2000s style!✓ New old stock! Still unused after all these years✓ Great alternative to buying new✓ Worldwide shipping

JFM Blue & White Squiggles Small Vintage Sleeveless Cycling Jersey

✓ Original vintage jersey - 1980s style!✓ Suitable for historic cycling events such as L'Eroica✓ Thoroughly checked & honestly graded✓ Great alternative to buying new✓ Worldwide shipping

Kalin Black NOS Classic 45 mm 1" Quill Stem

✓ Original part - produced in the 1990s✓ New old stock! Still unused after all these years✓ Lightweight for the era - just 278 grams✓ Worldwide shipping

Kalin Bullet Nose NOS Classic 25.4 mm Seatpost

✓ Original part - produced in the 1990s✓ New old stock! Still unused after all these years✓ Super lightweight for the era - only 153 grams!✓ Worldwide shipping

Kalin High Rise NOS Classic 110 mm 1" Quill Stem

✓ Original part - produced in the 1990s✓ New old stock! Still unused after all these years✓ Worldwide shipping

Kalloy Classic 30.2 mm Seatpost

✓ Original part - produced in the 1990s✓ Professionally checked & cleaned✓ Worldwide shipping

Kalloy Fluted Bullet Nose NOS Classic 26.4 mm Seatpost

✓ Original part - produced in the 1990s✓ New old stock! Still unused after all these years✓ Super lightweight for the era - only 91 grams!✓ Worldwide shipping

Kalloy Fluted NOS Vintage 26.8 mm Bullet Nose Seatpost

✓ Original part - in production from the 1980s to the 1990s✓ New old stock! Still unused after all these years✓ Worldwide shipping

Kalloy KL100 Silver Classic 100 mm 1" Quill Stem

✓ Original part - in production from the 1990s to the 2000s✓ Checked & cleaned✓ Worldwide shipping

Kalloy KL80 Silver NOS Classic 80 mm 1" Quill Stem

✓ Original part - produced in the 1990s✓ New old stock! Still unused after all these years✓ Worldwide shipping

Kalloy Red NOS Classic 110 mm 1 1/8" A-Head Stem

✓ Original part - produced in the 1990s✓ New old stock! Still unused after all these years✓ Worldwide shipping

Kalloy Red Vintage 95 mm 1" Quill Stem

✓ Original part - produced in the 1980s✓ Checked & cleaned✓ Worldwide shipping

Kalloy Uno NOS Classic 31.6 mm Seatpost

✓ Original part - produced in the 1990s✓ New old stock! Still unused after all these years✓ Lightweight for the era - just 286 grams✓ Worldwide shipping

Kalloy Uno Silver NOS Classic 130 mm 1 1/8" Quill Stem

✓ Original part - produced in the 1990s✓ New old stock! Still unused after all these years✓ Super lightweight for the era - only 237 grams!✓ Worldwide shipping

Kalloy Uno Silver NOS Classic 130 mm 1 1/8" Quill Stem

✓ Original part - produced in the 1990s✓ New old stock! Still unused after all these years✓ Super lightweight for the era - only 237 grams!✓ Worldwide shipping

Kas Cycling Cap

Kinlin T10 Retro 36h 27" Clincher Rim

✓ Professionally checked & cleaned✓ Timeless design - for original or retro styled bikes✓ Worldwide shipping

Kroon-Hypro Vintage Dutch Cotton Cycling Cap

✓ Original vintage cap - 1980s style!✓ Suitable for historic cycling events such as L'Eroica✓ Thoroughly checked & honestly graded✓ Great alternative to buying new✓ Worldwide shipping

KS Vintage Short Sleeve Cycling Jersey

Lampre - Fondital NOS Classic Cycling Cotton Cap

✓ Original classic cap - 2000s style!✓ New old stock! Still unused after all these years✓ Great alternative to buying new✓ Worldwide shipping

✓ Original toe straps - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

✓ Original bar tape - in production from the 1960s to the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

✓ Original pump - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

✓ Original pump - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

✓ Original pump - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

✓ Original pump - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & tested
✓ Worldwide shipping

✓ Original pump - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & tested
✓ Worldwide shipping

✓ Original part - produced in the 2000s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

✓ Original pedals - produced in the 1980s
✓ Professionally checked & cleaned
✓ Worldwide shipping

✓ Original bar tape - produced in the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

✓ Original saddle - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

✓ Original bar tape - produced in the 1980s
✓ New old stock & still in the original packaging!
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

✓ Original part - in production from the 1990s to the 2000s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

✓ Original toe straps - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

✓ Original classic cap - 2000s style!
✓ New old stock! Still unused after all these years
✓ Great alternative to buying new
✓ Worldwide shipping

✓ Original vintage jersey - 1980s style!
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & honestly graded
✓ Great alternative to buying new
✓ Worldwide shipping

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 278 grams
✓ Worldwide shipping

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 153 grams!
✓ Worldwide shipping

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

✓ Original part - produced in the 1990s
✓ Professionally checked & cleaned
✓ Worldwide shipping

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 91 grams!
✓ Worldwide shipping

✓ Original part - in production from the 1980s to the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

✓ Original part - in production from the 1990s to the 2000s
✓ Checked & cleaned
✓ Worldwide shipping

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

✓ Original part - produced in the 1980s
✓ Checked & cleaned
✓ Worldwide shipping

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 286 grams
✓ Worldwide shipping

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 237 grams!
✓ Worldwide shipping

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 237 grams!
✓ Worldwide shipping

✓ Professionally checked & cleaned
✓ Timeless design - for original or retro styled bikes
✓ Worldwide shipping

✓ Original vintage cap - 1980s style!
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & honestly graded
✓ Great alternative to buying new
✓ Worldwide shipping

✓ Original classic cap - 2000s style!
✓ New old stock! Still unused after all these years
✓ Great alternative to buying new
✓ Worldwide shipping

✓ Original classic cap - 2000s style!
✓ New old stock! Still unused after all these years
✓ Great alternative to buying new
✓ Worldwide shipping

✓ Original toe clips - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

✓ Original toe clips - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

✓ Original toe straps - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

✓ Original hub - produced in the 1970s
✓ Super lightweight for the era - only 169 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked, cleaned & serviced
✓ Worldwide shipping

✓ Original skewer - produced in the 1990s
✓ Checked & cleaned
✓ Worldwide shipping

✓ Original pedals - in production from the 1980s to the 1990s
✓ Professionally checked & cleaned
✓ Worldwide shipping

✓ Original classic cap - 1990s style!
✓ New old stock! Still unused after all these years
✓ Great alternative to buying new
✓ Worldwide shipping

✓ Original classic cap - 2000s style!
✓ New old stock! Still unused after all these years
✓ Great alternative to buying new
✓ Worldwide shipping