£17.50
Christophe 49 / 496 Z toe clips (or pedal cages if you prefer), hailing from France and in production during the 1980s. Made from alloy and weighing in at 29 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been checked, cleaned and graded as OK condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£9.38 £13.00
Christophe 50 / 506 toe clips, hailing from France and in production from the 1980s to the 1990s. Made from steel and weighing in at 72 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Type - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£13.50 £15.00
Christophe 50 / 506 toe clips (or pedal cages if you prefer), hailing from France and in production from the 1980s to the 1990s. Made from steel and weighing in at 71 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£13.50
Christophe 50 / 506 toe clips (or pedal cages if you prefer), hailing from France and in production from the 1980s to the 1990s. Made from steel and weighing in at 64 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been checked, cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£13.50 £15.00
Christophe 50 / 506 toe clips (or pedal cages if you prefer), hailing from France and in production from the 1920s to the 1970s. Made from steel and weighing in at 64 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£15.00
Christophe 50 / 506 toe clips (or pedal cages if you prefer), hailing from France and in production from the 1980s to the 1990s. Made from steel and weighing in at 63 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£8.63 £12.00
Christophe 50 / 506 toe clips, hailing from France and in production from the 1980s to the 1990s. Made from steel and weighing in at 75 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been cleaned, checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Type - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£7.50 £10.00
Christophe 50 / 506 toe clips, hailing from France and in production from the 1980s to the 1990s. Made from steel and weighing in at 64 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been cleaned, checked by one of our mechanics and graded as OK condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Type - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£29.75 £35.00
Christophe 50 / 506 toe clips, hailing from France and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from steel and weighing in at 58 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Type - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£15.75 £18.00
Christophe 50 / 506 toe clips (or pedal cages if you prefer), hailing from France and in production from the 1980s to the 1990s. Made from steel and weighing in at 64 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
The toe clips have been checked, cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£30.00 £40.00
Christophe 50 GC / 506 GC toe clips, hailing from France and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from steel and weighing in at 63 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe clips!
OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Type - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£20.00
Christophe 516 B toe straps (or pedal straps if you prefer), hailing from France and in production during the 1980s. The straps are blue in colour and made from leather/steel, the perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too of course!
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong toe straps!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£8.50
Christophe 516 N toe straps (or pedal straps if you prefer), hailing from France and in production during the 1990s. The straps are black in colour and made from leather/steel, the perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too of course!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£20.00
Christophe 516 T toe straps (or pedal straps if you prefer), hailing from France and in production during the 1990s. The straps are tan in colour and made from leather/steel, the perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too of course!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£17.50
Christophe 516 T toe straps (or pedal straps if you prefer), hailing from France and in production during the 1990s. The straps are tan in colour and made from leather/steel, the perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too of course!
The straps have been checked over, cleaned (as much as you can clean toe straps!) and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Toe Strap Type - standard toe clips are designed to accept single toe straps, but there are some that allow double toe straps to be fitted.
Strap Width - measured across one of the straps at its widest point.
Toe Strap Length - the total length including the buckle, measured to the nearest 0.5 cm.
£40.00
Cicli Debruyne - Assubel - Lokaal Edelweiss Klerken cycling jersey, hailing from Belgium and likely made in the 1980s/1990s given the style. An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
The jersey’s been thoroughly checked over and graded as good condition. If there are any issues worth noting we’ll do so in the overview section below, but please take a good look at the photos so you can see the condition yourself before you buy.OVERVIEW
DETAIL & MEASUREMENTS
Pit to Pit - this measurement is taken from the centre of one armpit to the other, across the chest with the jersey laid flat.
Top to Bottom - this will always be from the very top of the collar to the very bottom hem, we provide measurements for both the front and back, always taken with the jersey laid flat.
Shoulder Seam to Sleeve End - this measurement is taken from the shoulder seam down to the very end of the sleeve on the outside.
Across Neck - for consistency on all neck shapes we gather the front and back together and lay them flat, then measure across the stitching (as shown in the supporting photos).
Across Sleeve End - measured across the sleeve end, laid flat.





£38.25 £45.00
Cicli Guadrini chainring, hailing from Italy and in production during the 1980s. Made from aluminium and weighing in at 87 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica, Anjou Velo, Velo Retro or another similar vintage cycling event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong chainring!
The chainring's been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£21.25 £25.00
Ciclolinea headband (or sweat band if you prefer), likely made in the 1980s given the style (yet still new & unused after all this time!). An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headband!
OVERVIEW
DETAIL & MEASUREMENTS
£23.38 £27.50
Ciclolinea headband (or sweat band if you prefer), likely made in the 1980s given the style (yet still new & unused after all this time!). An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headband!
OVERVIEW
DETAIL & MEASUREMENTS
£7.50 £10.00
Ciclolinea bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£27.00 £30.00
Ciclolinea headband (or sweat band if you prefer), likely made in the 1980s given the style (yet still new & unused after all this time!). An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headband!
OVERVIEW
DETAIL & MEASUREMENTS
£21.25 £25.00
Ciclolinea headband (or sweat band if you prefer), likely made in the 1980s given the style (yet still new & unused after all this time!). An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headband!
OVERVIEW
DETAIL & MEASUREMENTS
£24.75 £27.50
Ciclolinea headband (or sweat band if you prefer), likely made in the 1980s given the style (yet still new & unused after all this time!). An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headband!
OVERVIEW
DETAIL & MEASUREMENTS
£21.25 £25.00
Ciclolinea headband (or sweat band if you prefer), likely made in the 1980s given the style (yet still new & unused after all this time!). An excellent choice for wearing on your vintage bike (or any occasion you fancy of course), and also a great alternative to buying brand new cycling kit!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong headband!
OVERVIEW
DETAIL & MEASUREMENTS
£18.75 £25.00
Ciclolinea Pelten Graphic bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£22.50 £30.00
Ciclolinea Pelten Shade bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Supplied as shown in the photos, enough tape to cover a set of drop bars. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or a similar vintage event, this is of the correct era, so rest assured the pre-1987 police won't lock you up for having the wrong handlebar grip!
OVERVIEW
TECHNICAL INFO
£25.00
Cinelli toe clips (or pedal cages if you prefer), hailing from Italy and in production from the 1990s to the 2000s. Made from steel and weighing in at 75 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
The toe clips have been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the shape & condition before you buy.OVERVIEW
**This is a guide based on traditional toe clip sizing for cycling shoes of the time, if you ride with chunkier shoes then we'd recommend going for a larger size. Please use this as a guide only and if possible use the length measurement provided to compare with toe clips you know fit well.
TECHNICAL INFO
Pedal Fixing - 'standard' toe clips fix to the front of the pedals, most will be of this type and work with both quill & platform pedals providing they have mounting holes in the correct place. There are also 'aero' ones that attach to the top, and side fixing versions too. 'Wide platform' fixings are similar to standard ones but the fixing holes are almost 3 inches apart.
Toe Strap Fit - most toe clips are designed to accept a single toe strap, but there are some less common ones that allow two toe straps to be fitted.
Length - this is measured from the fixing end to the toe end at the most extreme points, the same way the manufacturers measure and we use this to recommend the fit if there's no size stamped on them. All length measurements are rounded to the nearest 0.5 cm.
Distance Between Fixing Bolts - we measure this distance from the centre of one hole to the next (ctc), this usually only needs to be close, not exact, providing the holes on the toe clips are oblong shaped to allow a decent amount of wiggle room (most toe clips are made this way).
£114.75 £135.00
Cinelli 101 stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 282 grams - pretty lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.
OVERVIEW
TECHNICAL INFO
£90.00 £120.00
Cinelli 101 stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 290 grams - pretty lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.
Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".
Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.
Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.
Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
£56.25 £75.00
Cinelli 1A stem, hailing from Italy and in production during the 1970s. Made from aluminium and weighing in at 283 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!
The stem's been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.
Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".
Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.
Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.
Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
£101.25 £135.00
Cinelli 1A stem, hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from aluminium and weighing in at 272 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!
OVERVIEW
TECHNICAL INFO
£114.75 £135.00
Cinelli 1A stem, hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from aluminium and weighing in at 324 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!
OVERVIEW
TECHNICAL INFO
£150.00
Cinelli Alter ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 305 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.
Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.
Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).
Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.
£55.25 £65.00
Cinelli Campione Del Mondo drop handlebars, hailing from Italy and in production from the 1980s to the 1990s. Made from aluminium and weighing in at 320 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bars!
The bars have been checked, handlebar tape residue removed and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Width (ctc)* - measured at the ends of the drops, from the centre of one side to the other (ctc), to the nearest cm. In some cases the bars may display a different width as some brands measure outside to outside rather than ctc, but we always use this measurement for consistency.
Shape - Classic' drops have a smooth curve, 'anatomic' have multiple angles for different hand positions, 'compact' are short reach with a shallow drop and randonneur bars are usually classic in shape but flare out at the drops.
Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.
Drop (ctc) - from the top flat section to the bottom of the drops, measured from the centre of one to the other with the flat part at the end of the drops parrallel to the ground.
Reach (ctc) - measured from the centre of the top section to the centre of the 'curve' at its furthest point, giving you the maximum reach. We measure this with the flat part at the end of of the drops parrallel to the ground.
Cable Groove - these allow you to run your cables neatly underneath the handlebar tape, if your setup requires this.
£65.00
Cinelli Campione Del Mondo drop handlebars, hailing from Italy and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 330 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Width (ctc)* - measured at the ends of the drops, from the centre of one side to the other (ctc), to the nearest cm. In some cases the bars may display a different width as some brands measure outside to outside rather than ctc, but we always use this measurement for consistency.
Shape - Classic' drops have a smooth curve, 'anatomic' have multiple angles for different hand positions, 'compact' are short reach with a shallow drop and randonneur bars are usually classic in shape but flare out at the drops.
Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.
Drop (ctc) - from the top flat section to the bottom of the drops, measured from the centre of one to the other with the flat part at the end of the drops parrallel to the ground.
Reach (ctc) - measured from the centre of the top section to the centre of the 'curve' at its furthest point, giving you the maximum reach. We measure this with the flat part at the end of of the drops parrallel to the ground.
Cable Groove - these allow you to run your cables neatly underneath the handlebar tape, if your setup requires this.
£40.00
Cinelli Campus drop handlebars, hailing from Italy and in production from the 1980s to the 1990s. Made from aluminium and weighing in at 325 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The bars have been checked, handlebar tape residue removed and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Width (ctc)* - measured at the bottom of the drops, from the centre of one side to the other (ctc), to the nearest cm. In some cases the bars may display a different width as some brands measure outside to outside rather than ctc, but we always use this measurement for consistency.
Shape - Classic' drops have a smooth curve, 'anatomic' have multiple angles for different hand positions, 'compact' are short reach with a shallow drop and randonneur bars are usually classic in shape but rise up then flare out at the drops.
Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.
Drop (ctc) - from the top flat section to the bottom of the drops, measured from the centre of one to the other with the flat part at the end of the drops parrallel to the ground.
Reach (ctc) - measured from the centre of the top section to the centre of the 'curve' at its furthest point, giving you the maximum reach. We measure this with the flat part at the end of of the drops parrallel to the ground.
Cable Groove - these allow you to run your cables neatly underneath the handlebar tape, if your setup requires this.
£93.75 £125.00
Cinelli Criterium drop handlebars, hailing from Italy and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 315 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Width (ctc)* - measured at the ends of the drops, from the centre of one side to the other (ctc), to the nearest cm. In some cases the bars may display a different width as some brands measure outside to outside rather than ctc, but we always use this measurement for consistency.
Shape - Classic' drops have a smooth curve, 'anatomic' have multiple angles for different hand positions, 'compact' are short reach with a shallow drop and randonneur bars are usually classic in shape but flare out at the drops.
Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.
Drop (ctc) - from the top flat section to the bottom of the drops, measured from the centre of one to the other with the flat part at the end of the drops parrallel to the ground.
Reach (ctc) - measured from the centre of the top section to the centre of the 'curve' at its furthest point, giving you the maximum reach. We measure this with the flat part at the end of of the drops parrallel to the ground.
Cable Groove - these allow you to run your cables neatly underneath the handlebar tape, if your setup requires this.
£33.25 £35.00
Cinelli Criterium drop handlebars, hailing from Italy and in production from the 1980s to the 1990s. Made from aluminium and weighing in at 325 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The bars have been checked, handlebar tape residue removed and graded as OK condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Width (ctc)* - measured at the ends of the drops, from the centre of one side to the other (ctc), to the nearest cm. In some cases the bars may display a different width as some brands measure outside to outside rather than ctc, but we always use this measurement for consistency.
Shape - Classic' drops have a smooth curve, 'anatomic' have multiple angles for different hand positions, 'compact' are short reach with a shallow drop and randonneur bars are usually classic in shape but rise up then flare out at the drops.
Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.
Drop (ctc) - from the top flat section to the bottom of the drops, measured from the centre of one to the other with the flat part at the end of the drops parrallel to the ground.
Reach (ctc) - measured from the centre of the top section to the centre of the 'curve' at its furthest point, giving you the maximum reach. We measure this with the flat part at the end of of the drops parrallel to the ground.
Cable Groove - these allow you to run your cables neatly underneath the handlebar tape, if your setup requires this.
£56.25 £75.00
Cinelli Diet Eubios drop handlebars, hailing from Italy and in production from the 1990s to the 2000s (yet still new & unused after all this time!). Made from aluminium and weighing in at 275 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Width (ctc)* - measured at the ends of the drops, from the centre of one side to the other (ctc), to the nearest cm. In some cases the bars may display a different width as some brands measure outside to outside rather than ctc, but we always use this measurement for consistency.
Shape - Classic' drops have a smooth curve, 'anatomic' have multiple angles for different hand positions, 'compact' are short reach with a shallow drop and randonneur bars are usually classic in shape but flare out at the drops.
Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.
Drop (ctc) - from the top flat section to the bottom of the drops, measured from the centre of one to the other with the flat part at the end of the drops parrallel to the ground.
Reach (ctc) - measured from the centre of the top section to the centre of the 'curve' at its furthest point, giving you the maximum reach. We measure this with the flat part at the end of of the drops parrallel to the ground.
Cable Groove - these allow you to run your cables neatly underneath the handlebar tape, if your setup requires this.
£48.75 £65.00
Cinelli Giro D'Italia drop handlebars, hailing from Italy and in production during the 1990s. Made from aluminium and weighing in at 309 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.
The bars have been checked by one of our mechanics, handlebar tape residue removed and graded as excellent condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£95.00
Cinelli Giro D'Italia drop handlebars, hailing from Italy and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 320 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
OVERVIEW
TECHNICAL INFO
Width (ctc)* - measured at the ends of the drops, from the centre of one side to the other (ctc), to the nearest cm. In some cases the bars may display a different width as some brands measure outside to outside rather than ctc, but we always use this measurement for consistency.
Shape - Classic' drops have a smooth curve, 'anatomic' have multiple angles for different hand positions, 'compact' are short reach with a shallow drop and randonneur bars are usually classic in shape but rise up then flare out at the drops.
Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.
Drop (ctc) - from the top flat section to the bottom of the drops, measured from the centre of one to the other with the flat part at the end of the drops parrallel to the ground.
Reach (ctc) - measured from the centre of the top section to the centre of the 'curve' at its furthest point, giving you the maximum reach. We measure this with the flat part at the end of of the drops parrallel to the ground.
Cable Groove - these allow you to run your cables neatly underneath the handlebar tape, if your setup requires this.
£42.50 £50.00
Cinelli Giro D'Italia drop handlebars, hailing from Italy and in production from the 1980s to the 1990s. Made from aluminium and weighing in at 318 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The bars have been checked, handlebar tape residue removed and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Width (ctc)* - measured at the ends of the drops, from the centre of one side to the other (ctc), to the nearest cm. In some cases the bars may display a different width as some brands measure outside to outside rather than ctc, but we always use this measurement for consistency.
Shape - Classic' drops have a smooth curve, 'anatomic' have multiple angles for different hand positions, 'compact' are short reach with a shallow drop and randonneur bars are usually classic in shape but rise up then flare out at the drops.
Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.
Drop (ctc) - from the top flat section to the bottom of the drops, measured from the centre of one to the other with the flat part at the end of the drops parrallel to the ground.
Reach (ctc) - measured from the centre of the top section to the centre of the 'curve' at its furthest point, giving you the maximum reach. We measure this with the flat part at the end of of the drops parrallel to the ground.
Cable Groove - these allow you to run your cables neatly underneath the handlebar tape, if your setup requires this.
£41.25 £55.00
Cinelli Giro D'Italia drop handlebars, hailing from Italy and in production from the 1970s to the 1980s. Made from aluminium and weighing in at 317 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong bars!
The bars have been checked by one of our mechanics, handlebar tape residue removed and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
£20.00
Cinelli bar end caps (or plugs, or stoppers if you prefer), hailing from Italy and in production from the 1960s to the 1970s. Made from plastic and weighing in at 7 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong handlebar caps!
The caps have been checked, cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Inner Diameter - most end caps will fit most classic drop bars and they do flex a little to give you some wiggle room. However, it's worth double checking this measurement to ensure the caps will fit your handlebars with bar tape fitted.
End Diameter - the diameter at the closed end stop, at its widest part.
£17.50
Cinelli bar end caps (or plugs, or stoppers if you prefer), hailing from Italy and in production from the 1960s to the 1970s. Made from plastic and weighing in at 7 grams (for the pair). A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong handlebar caps!
The caps have been checked, cleaned and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Inner Diameter - most end caps will fit most classic drop bars and they do flex a little to give you some wiggle room. However, it's worth double checking this measurement to ensure the caps will fit your handlebars with bar tape fitted.
End Diameter - the diameter at the closed end stop, at its widest part.
£75.00
Cinelli Model 1A handlebar stem (or gooseneck if you prefer), hailing from Italy and in production during the 1970s. Made from aluminium/steel and weighing in at 310 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!
The stem's been carefully cleaned, thoroughly checked and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through the middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.
Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".
Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.
Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.
Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
£71.25 £75.00
Cinelli Model 1A handlebar stem (or gooseneck if you prefer), hailing from Italy and in production during the 1970s. Made from aluminium/steel and weighing in at 275 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!
The stem's been carefully cleaned, thoroughly checked and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.
Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".
Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.
Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.
Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
£51.00 £60.00
Cinelli Model 1A stem, hailing from Italy and in production from the 1970s to the 1980s. Made from aluminium and weighing in at 292 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!
The stem's been carefully cleaned, thoroughly checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.
Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".
Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.
Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.
Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
£55.25 £65.00
Cinelli Model 1A stem, hailing from Italy and in production from the 1970s to the 1980s. Made from aluminium/steel and weighing in at 292 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!
The stem's been carefully cleaned, thoroughly checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.
Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".
Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.
Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.
Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
£55.25 £65.00
Cinelli Model 1A stem, hailing from Italy and in production from the 1970s to the 1980s. Made from aluminium/steel and weighing in at 307 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!
The stem's been carefully cleaned, thoroughly checked and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
TECHNICAL INFO
Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.
Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".
Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.
Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.
Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
SUBSCRIBE TO GET THE FIRST SCOOP
Exclusive content, new products, subscriber only promotions. Delivered to your inbox by tiny cyclists, every few weeks.
Don't worry, you can unsubscribe at any time.
PEDAL PEDLAR
T: 02036758003 // E: info@pedalpedlar.co.uk
© 2026 Pedal Pedlar.
Ecommerce Software by Shopify